/* SPDX-License-Identifier: GPL-2.0+ */ /* * (C) Copyright 2004-2010 * Texas Instruments, <www.ti.com> */ #ifndef _OMAP2PLUS_I2C_H_ #define _OMAP2PLUS_I2C_H_ /* I2C masks */ /* I2C Interrupt Enable Register (I2C_IE): */ #define I2C_IE_GC_IE (1 << 5) #define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */ #define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */ #define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */ #define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */ #define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */ /* I2C Status Register (I2C_STAT): */ #define I2C_STAT_SBD (1 << 15) /* Single byte data */ #define I2C_STAT_BB (1 << 12) /* Bus busy */ #define I2C_STAT_ROVR (1 << 11) /* Receive overrun */ #define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ #define I2C_STAT_AAS (1 << 9) /* Address as slave */ #define I2C_STAT_GC (1 << 5) #define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ #define I2C_STAT_RRDY (1 << 3) /* Receive data ready */ #define I2C_STAT_ARDY (1 << 2) /* Register access ready */ #define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */ #define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */ /* I2C Interrupt Code Register (I2C_INTCODE): */ #define I2C_INTCODE_MASK 7 #define I2C_INTCODE_NONE 0 #define I2C_INTCODE_AL 1 /* Arbitration lost */ #define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */ #define I2C_INTCODE_ARDY 3 /* Register access ready */ #define I2C_INTCODE_RRDY 4 /* Rcv data ready */ #define I2C_INTCODE_XRDY 5 /* Xmit data ready */ /* I2C Buffer Configuration Register (I2C_BUF): */ #define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */ #define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */ /* I2C Configuration Register (I2C_CON): */ #define I2C_CON_EN (1 << 15) /* I2C module enable */ #define I2C_CON_BE (1 << 14) /* Big endian mode */ #define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */ #define I2C_CON_MST (1 << 10) /* Master/slave mode */ #define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode */ /* (master mode only) */ #define I2C_CON_XA (1 << 8) /* Expand address */ #define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */ #define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */ /* I2C System Test Register (I2C_SYSTEST): */ #define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ #define I2C_SYSTEST_FREE (1 << 14) /* Free running mode, on brkpoint) */ #define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ #define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ #define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */ #define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */ #define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */ #define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */ /* I2C System Status Register (I2C_SYSS): */ #define I2C_SYSS_RDONE (1 << 0) /* Internel reset monitoring */ #define I2C_SCLL_SCLL 0 #define I2C_SCLL_SCLL_M 0xFF #define I2C_SCLL_HSSCLL 8 #define I2C_SCLH_HSSCLL_M 0xFF #define I2C_SCLH_SCLH 0 #define I2C_SCLH_SCLH_M 0xFF #define I2C_SCLH_HSSCLH 8 #define I2C_SCLH_HSSCLH_M 0xFF #define OMAP_I2C_STANDARD 100000 #define OMAP_I2C_FAST_MODE 400000 #define OMAP_I2C_HIGH_SPEED 3400000 #define SYSTEM_CLOCK_12 12000000 #define SYSTEM_CLOCK_13 13000000 #define SYSTEM_CLOCK_192 19200000 #define SYSTEM_CLOCK_96 96000000 /* Use the reference value of 96MHz if not explicitly set by the board */ #ifndef I2C_IP_CLK #define I2C_IP_CLK SYSTEM_CLOCK_96 #endif /* * The reference minimum clock for high speed is 19.2MHz. * The linux 2.6.30 kernel uses this value. * The reference minimum clock for fast mode is 9.6MHz * The reference minimum clock for standard mode is 4MHz * In TRM, the value of 12MHz is used. */ #ifndef I2C_INTERNAL_SAMPLING_CLK #define I2C_INTERNAL_SAMPLING_CLK 19200000 #endif /* * The equation for the low and high time is * tlow = scll + scll_trim = (sampling clock * tlow_duty) / speed * thigh = sclh + sclh_trim = (sampling clock * (1 - tlow_duty)) / speed * * If the duty cycle is 50% * * tlow = scll + scll_trim = sampling clock / (2 * speed) * thigh = sclh + sclh_trim = sampling clock / (2 * speed) * * In TRM * scll_trim = 7 * sclh_trim = 5 * * The linux 4.9 kernel uses * scll_trim = 7 * sclh_trim = 5 * * These are the trim values for standard and fast speed */ #ifndef I2C_FASTSPEED_SCLL_TRIM #define I2C_FASTSPEED_SCLL_TRIM 7 #endif #ifndef I2C_FASTSPEED_SCLH_TRIM #define I2C_FASTSPEED_SCLH_TRIM 5 #endif /* These are the trim values for high speed */ #ifndef I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM #define I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM #endif #ifndef I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM #define I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM #endif #ifndef I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM #define I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM #endif #ifndef I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM #define I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM #endif #define I2C_PSC_MAX 0x0f #define I2C_PSC_MIN 0x00 #endif /* _OMAP24XX_I2C_H_ */