/******************************************************************************
*
* Copyright 1999-2012 Broadcom Corporation
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
#ifndef GATT_API_H
#define GATT_API_H
#include "bt_target.h"
#include "btm_ble_api.h"
#include "gattdefs.h"
/*****************************************************************************
* Constants
****************************************************************************/
/* Success code and error codes */
#define GATT_SUCCESS 0x00
#define GATT_INVALID_HANDLE 0x01
#define GATT_READ_NOT_PERMIT 0x02
#define GATT_WRITE_NOT_PERMIT 0x03
#define GATT_INVALID_PDU 0x04
#define GATT_INSUF_AUTHENTICATION 0x05
#define GATT_REQ_NOT_SUPPORTED 0x06
#define GATT_INVALID_OFFSET 0x07
#define GATT_INSUF_AUTHORIZATION 0x08
#define GATT_PREPARE_Q_FULL 0x09
#define GATT_NOT_FOUND 0x0a
#define GATT_NOT_LONG 0x0b
#define GATT_INSUF_KEY_SIZE 0x0c
#define GATT_INVALID_ATTR_LEN 0x0d
#define GATT_ERR_UNLIKELY 0x0e
#define GATT_INSUF_ENCRYPTION 0x0f
#define GATT_UNSUPPORT_GRP_TYPE 0x10
#define GATT_INSUF_RESOURCE 0x11
#define GATT_ILLEGAL_PARAMETER 0x87
#define GATT_NO_RESOURCES 0x80
#define GATT_INTERNAL_ERROR 0x81
#define GATT_WRONG_STATE 0x82
#define GATT_DB_FULL 0x83
#define GATT_BUSY 0x84
#define GATT_ERROR 0x85
#define GATT_CMD_STARTED 0x86
#define GATT_PENDING 0x88
#define GATT_AUTH_FAIL 0x89
#define GATT_MORE 0x8a
#define GATT_INVALID_CFG 0x8b
#define GATT_SERVICE_STARTED 0x8c
#define GATT_ENCRYPED_MITM GATT_SUCCESS
#define GATT_ENCRYPED_NO_MITM 0x8d
#define GATT_NOT_ENCRYPTED 0x8e
#define GATT_CONGESTED 0x8f
#define GATT_DUP_REG 0x90 /* 0x90 */
#define GATT_ALREADY_OPEN 0x91 /* 0x91 */
#define GATT_CANCEL 0x92 /* 0x92 */
/* 0xE0 ~ 0xFC reserved for future use */
/* Client Characteristic Configuration Descriptor Improperly Configured */
#define GATT_CCC_CFG_ERR 0xFD
/* Procedure Already in progress */
#define GATT_PRC_IN_PROGRESS 0xFE
/* Attribute value out of range */
#define GATT_OUT_OF_RANGE 0xFF
typedef uint8_t tGATT_STATUS;
#define GATT_RSP_ERROR 0x01
#define GATT_REQ_MTU 0x02
#define GATT_RSP_MTU 0x03
#define GATT_REQ_FIND_INFO 0x04
#define GATT_RSP_FIND_INFO 0x05
#define GATT_REQ_FIND_TYPE_VALUE 0x06
#define GATT_RSP_FIND_TYPE_VALUE 0x07
#define GATT_REQ_READ_BY_TYPE 0x08
#define GATT_RSP_READ_BY_TYPE 0x09
#define GATT_REQ_READ 0x0A
#define GATT_RSP_READ 0x0B
#define GATT_REQ_READ_BLOB 0x0C
#define GATT_RSP_READ_BLOB 0x0D
#define GATT_REQ_READ_MULTI 0x0E
#define GATT_RSP_READ_MULTI 0x0F
#define GATT_REQ_READ_BY_GRP_TYPE 0x10
#define GATT_RSP_READ_BY_GRP_TYPE 0x11
/* 0001-0010 (write)*/
#define GATT_REQ_WRITE 0x12
#define GATT_RSP_WRITE 0x13
/* changed in V4.0 01001-0010(write cmd)*/
#define GATT_CMD_WRITE 0x52
#define GATT_REQ_PREPARE_WRITE 0x16
#define GATT_RSP_PREPARE_WRITE 0x17
#define GATT_REQ_EXEC_WRITE 0x18
#define GATT_RSP_EXEC_WRITE 0x19
#define GATT_HANDLE_VALUE_NOTIF 0x1B
#define GATT_HANDLE_VALUE_IND 0x1D
#define GATT_HANDLE_VALUE_CONF 0x1E
/* changed in V4.0 1101-0010 (signed write) see write cmd above*/
#define GATT_SIGN_CMD_WRITE 0xD2
/* 0x1E = 30 + 1 = 31*/
#define GATT_OP_CODE_MAX (GATT_HANDLE_VALUE_CONF + 1)
#define GATT_HANDLE_IS_VALID(x) ((x) != 0)
#define GATT_CONN_UNKNOWN 0
/* general L2cap failure */
#define GATT_CONN_L2C_FAILURE 1
/* 0x08 connection timeout */
#define GATT_CONN_TIMEOUT HCI_ERR_CONNECTION_TOUT
/* 0x13 connection terminate by peer user */
#define GATT_CONN_TERMINATE_PEER_USER HCI_ERR_PEER_USER
/* 0x16 connectionterminated by local host */
#define GATT_CONN_TERMINATE_LOCAL_HOST HCI_ERR_CONN_CAUSE_LOCAL_HOST
/* 0x03E connection fail to establish */
#define GATT_CONN_FAIL_ESTABLISH HCI_ERR_CONN_FAILED_ESTABLISHMENT
/* 0x22 connection fail for LMP response tout */
#define GATT_CONN_LMP_TIMEOUT HCI_ERR_LMP_RESPONSE_TIMEOUT
/* 0x0100 L2CAP connection cancelled */
#define GATT_CONN_CANCEL L2CAP_CONN_CANCEL
typedef uint16_t tGATT_DISCONN_REASON;
/* MAX GATT MTU size
*/
#ifndef GATT_MAX_MTU_SIZE
#define GATT_MAX_MTU_SIZE 517
#endif
/* max legth of an attribute value
*/
#ifndef GATT_MAX_ATTR_LEN
#define GATT_MAX_ATTR_LEN 600
#endif
/* default GATT MTU size over LE link
*/
#define GATT_DEF_BLE_MTU_SIZE 23
/* invalid connection ID
*/
#define GATT_INVALID_CONN_ID 0xFFFF
#ifndef GATT_CL_MAX_LCB
#define GATT_CL_MAX_LCB 22
#endif
/* GATT notification caching timer, default to be three seconds
*/
#ifndef GATTC_NOTIF_TIMEOUT
#define GATTC_NOTIF_TIMEOUT 3
#endif
/*****************************************************************************
* GATT Structure Definition
****************************************************************************/
/* Attribute permissions
*/
#define GATT_PERM_READ (1 << 0) /* bit 0 */
#define GATT_PERM_READ_ENCRYPTED (1 << 1) /* bit 1 */
#define GATT_PERM_READ_ENC_MITM (1 << 2) /* bit 2 */
#define GATT_PERM_WRITE (1 << 4) /* bit 4 */
#define GATT_PERM_WRITE_ENCRYPTED (1 << 5) /* bit 5 */
#define GATT_PERM_WRITE_ENC_MITM (1 << 6) /* bit 6 */
#define GATT_PERM_WRITE_SIGNED (1 << 7) /* bit 7 */
#define GATT_PERM_WRITE_SIGNED_MITM (1 << 8) /* bit 8 */
typedef uint16_t tGATT_PERM;
/* the MS nibble of tGATT_PERM; key size 7=0; size 16=9 */
#define GATT_ENCRYPT_KEY_SIZE_MASK (0xF000)
#define GATT_READ_ALLOWED \
(GATT_PERM_READ | GATT_PERM_READ_ENCRYPTED | GATT_PERM_READ_ENC_MITM)
#define GATT_READ_AUTH_REQUIRED (GATT_PERM_READ_ENCRYPTED)
#define GATT_READ_MITM_REQUIRED (GATT_PERM_READ_ENC_MITM)
#define GATT_READ_ENCRYPTED_REQUIRED \
(GATT_PERM_READ_ENCRYPTED | GATT_PERM_READ_ENC_MITM)
#define GATT_WRITE_ALLOWED \
(GATT_PERM_WRITE | GATT_PERM_WRITE_ENCRYPTED | GATT_PERM_WRITE_ENC_MITM | \
GATT_PERM_WRITE_SIGNED | GATT_PERM_WRITE_SIGNED_MITM)
#define GATT_WRITE_AUTH_REQUIRED \
(GATT_PERM_WRITE_ENCRYPTED | GATT_PERM_WRITE_SIGNED)
#define GATT_WRITE_MITM_REQUIRED \
(GATT_PERM_WRITE_ENC_MITM | GATT_PERM_WRITE_SIGNED_MITM)
#define GATT_WRITE_ENCRYPTED_PERM \
(GATT_PERM_WRITE_ENCRYPTED | GATT_PERM_WRITE_ENC_MITM)
#define GATT_WRITE_SIGNED_PERM \
(GATT_PERM_WRITE_SIGNED | GATT_PERM_WRITE_SIGNED_MITM)
/* Characteristic properties
*/
#define GATT_CHAR_PROP_BIT_BROADCAST (1 << 0)
#define GATT_CHAR_PROP_BIT_READ (1 << 1)
#define GATT_CHAR_PROP_BIT_WRITE_NR (1 << 2)
#define GATT_CHAR_PROP_BIT_WRITE (1 << 3)
#define GATT_CHAR_PROP_BIT_NOTIFY (1 << 4)
#define GATT_CHAR_PROP_BIT_INDICATE (1 << 5)
#define GATT_CHAR_PROP_BIT_AUTH (1 << 6)
#define GATT_CHAR_PROP_BIT_EXT_PROP (1 << 7)
typedef uint8_t tGATT_CHAR_PROP;
/* Format of the value of a characteristic. enumeration type
*/
enum {
GATT_FORMAT_RES, /* rfu */
GATT_FORMAT_BOOL, /* 0x01 boolean */
GATT_FORMAT_2BITS, /* 0x02 2 bit */
GATT_FORMAT_NIBBLE, /* 0x03 nibble */
GATT_FORMAT_UINT8, /* 0x04 uint8 */
GATT_FORMAT_UINT12, /* 0x05 uint12 */
GATT_FORMAT_UINT16, /* 0x06 uint16 */
GATT_FORMAT_UINT24, /* 0x07 uint24 */
GATT_FORMAT_UINT32, /* 0x08 uint32 */
GATT_FORMAT_UINT48, /* 0x09 uint48 */
GATT_FORMAT_UINT64, /* 0x0a uint64 */
GATT_FORMAT_UINT128, /* 0x0B uint128 */
GATT_FORMAT_SINT8, /* 0x0C signed 8 bit integer */
GATT_FORMAT_SINT12, /* 0x0D signed 12 bit integer */
GATT_FORMAT_SINT16, /* 0x0E signed 16 bit integer */
GATT_FORMAT_SINT24, /* 0x0F signed 24 bit integer */
GATT_FORMAT_SINT32, /* 0x10 signed 32 bit integer */
GATT_FORMAT_SINT48, /* 0x11 signed 48 bit integer */
GATT_FORMAT_SINT64, /* 0x12 signed 64 bit integer */
GATT_FORMAT_SINT128, /* 0x13 signed 128 bit integer */
GATT_FORMAT_FLOAT32, /* 0x14 float 32 */
GATT_FORMAT_FLOAT64, /* 0x15 float 64*/
GATT_FORMAT_SFLOAT, /* 0x16 IEEE-11073 16 bit SFLOAT */
GATT_FORMAT_FLOAT, /* 0x17 IEEE-11073 32 bit SFLOAT */
GATT_FORMAT_DUINT16, /* 0x18 IEEE-20601 format */
GATT_FORMAT_UTF8S, /* 0x19 UTF-8 string */
GATT_FORMAT_UTF16S, /* 0x1a UTF-16 string */
GATT_FORMAT_STRUCT, /* 0x1b Opaque structure*/
GATT_FORMAT_MAX /* 0x1c or above reserved */
};
typedef uint8_t tGATT_FORMAT;
/* Characteristic Presentation Format Descriptor value
*/
typedef struct {
uint16_t unit; /* as UUIUD defined by SIG */
uint16_t descr; /* as UUID as defined by SIG */
tGATT_FORMAT format;
int8_t exp;
uint8_t name_spc; /* The name space of the description */
} tGATT_CHAR_PRES;
/* Characteristic Report reference Descriptor format
*/
typedef struct {
uint8_t rpt_id; /* report ID */
uint8_t rpt_type; /* report type */
} tGATT_CHAR_RPT_REF;
#define GATT_VALID_RANGE_MAX_SIZE 16
typedef struct {
uint8_t format;
uint16_t len;
uint8_t lower_range[GATT_VALID_RANGE_MAX_SIZE]; /* in little endian format */
uint8_t upper_range[GATT_VALID_RANGE_MAX_SIZE];
} tGATT_VALID_RANGE;
/* Characteristic Aggregate Format attribute value
*/
#define GATT_AGGR_HANDLE_NUM_MAX 10
typedef struct {
uint8_t num_handle;
uint16_t handle_list[GATT_AGGR_HANDLE_NUM_MAX];
} tGATT_CHAR_AGGRE;
/* Characteristic descriptor: Extended Properties value
*/
/* permits reliable writes of the Characteristic Value */
#define GATT_CHAR_BIT_REL_WRITE 0x0001
/* permits writes to the characteristic descriptor */
#define GATT_CHAR_BIT_WRITE_AUX 0x0002
/* characteristic descriptor: client configuration value
*/
#define GATT_CLT_CONFIG_NONE 0x0000
#define GATT_CLT_CONFIG_NOTIFICATION 0x0001
#define GATT_CLT_CONFIG_INDICATION 0x0002
/* characteristic descriptor: server configuration value
*/
#define GATT_SVR_CONFIG_NONE 0x0000
#define GATT_SVR_CONFIG_BROADCAST 0x0001
typedef uint16_t tGATT_SVR_CHAR_CONFIG;
/* Characteristic descriptor: Extended Properties value
*/
/* permits reliable writes of the Characteristic Value */
#define GATT_CHAR_BIT_REL_WRITE 0x0001
/* permits writes to the characteristic descriptor */
#define GATT_CHAR_BIT_WRITE_AUX 0x0002
/* authentication requirement
*/
#define GATT_AUTH_REQ_NONE 0
#define GATT_AUTH_REQ_NO_MITM 1 /* unauthenticated encryption */
#define GATT_AUTH_REQ_MITM 2 /* authenticated encryption */
#define GATT_AUTH_REQ_SIGNED_NO_MITM 3
#define GATT_AUTH_REQ_SIGNED_MITM 4
typedef uint8_t tGATT_AUTH_REQ;
/* Attribute Value structure
*/
typedef struct {
uint16_t conn_id;
uint16_t handle; /* attribute handle */
uint16_t offset; /* attribute value offset, if no offfset is needed for the
command, ignore it */
uint16_t len; /* length of attribute value */
tGATT_AUTH_REQ auth_req; /* authentication request */
uint8_t value[GATT_MAX_ATTR_LEN]; /* the actual attribute value */
} tGATT_VALUE;
/* Union of the event data which is used in the server respond API to carry the
* server response information
*/
typedef union {
/* data type member event */
tGATT_VALUE attr_value; /* READ, HANDLE_VALUE_IND, PREPARE_WRITE */
/* READ_BLOB, READ_BY_TYPE */
uint16_t handle; /* WRITE, WRITE_BLOB */
} tGATTS_RSP;
/* Transports for the primary service */
#define GATT_TRANSPORT_LE BT_TRANSPORT_LE
#define GATT_TRANSPORT_BR_EDR BT_TRANSPORT_BR_EDR
#define GATT_TRANSPORT_LE_BR_EDR (BT_TRANSPORT_LE | BT_TRANSPORT_BR_EDR)
typedef uint8_t tGATT_TRANSPORT;
#define GATT_PREP_WRITE_CANCEL 0x00
#define GATT_PREP_WRITE_EXEC 0x01
typedef uint8_t tGATT_EXEC_FLAG;
/* read request always based on UUID */
typedef struct {
uint16_t handle;
uint16_t offset;
bool is_long;
bt_gatt_db_attribute_type_t
gatt_type; /* are we writing characteristic or descriptor */
} tGATT_READ_REQ;
/* write request data */
typedef struct {
uint16_t handle; /* attribute handle */
uint16_t offset; /* attribute value offset, if no offfset is needed for the
command, ignore it */
uint16_t len; /* length of attribute value */
uint8_t value[GATT_MAX_ATTR_LEN]; /* the actual attribute value */
bool need_rsp; /* need write response */
bool is_prep; /* is prepare write */
bt_gatt_db_attribute_type_t
gatt_type; /* are we writing characteristic or descriptor */
} tGATT_WRITE_REQ;
/* callback data for server access request from client */
typedef union {
tGATT_READ_REQ read_req; /* read request, read by Type, read blob */
tGATT_WRITE_REQ write_req; /* write */
/* prepare write */
/* write blob */
uint16_t handle; /* handle value confirmation */
uint16_t mtu; /* MTU exchange request */
tGATT_EXEC_FLAG exec_write; /* execute write */
} tGATTS_DATA;
typedef uint8_t tGATT_SERV_IF; /* GATT Service Interface */
enum {
GATTS_REQ_TYPE_READ_CHARACTERISTIC = 1, /* Char read request */
GATTS_REQ_TYPE_READ_DESCRIPTOR, /* Desc read request */
GATTS_REQ_TYPE_WRITE_CHARACTERISTIC, /* Char write request */
GATTS_REQ_TYPE_WRITE_DESCRIPTOR, /* Desc write request */
GATTS_REQ_TYPE_WRITE_EXEC, /* Execute write */
GATTS_REQ_TYPE_MTU, /* MTU exchange information */
GATTS_REQ_TYPE_CONF /* handle value confirmation */
};
typedef uint8_t tGATTS_REQ_TYPE;
/* Client Used Data Structure
*/
/* definition of different discovery types */
enum {
GATT_DISC_SRVC_ALL = 1, /* discover all services */
GATT_DISC_SRVC_BY_UUID, /* discover service of a special type */
GATT_DISC_INC_SRVC, /* discover the included service within a service */
GATT_DISC_CHAR, /* discover characteristics of a service with/without type
requirement */
GATT_DISC_CHAR_DSCPT, /* discover characteristic descriptors of a character */
GATT_DISC_MAX /* maximnun discover type */
};
typedef uint8_t tGATT_DISC_TYPE;
/* GATT read type enumeration
*/
enum {
GATT_READ_BY_TYPE = 1,
GATT_READ_BY_HANDLE,
GATT_READ_MULTIPLE,
GATT_READ_CHAR_VALUE,
GATT_READ_PARTIAL,
GATT_READ_MAX
};
typedef uint8_t tGATT_READ_TYPE;
/* Read By Type Request (GATT_READ_BY_TYPE) Data
*/
typedef struct {
tGATT_AUTH_REQ auth_req;
uint16_t s_handle;
uint16_t e_handle;
bluetooth::Uuid uuid;
} tGATT_READ_BY_TYPE;
/* GATT_READ_MULTIPLE request data
*/
#define GATT_MAX_READ_MULTI_HANDLES \
10 /* Max attributes to read in one request */
typedef struct {
tGATT_AUTH_REQ auth_req;
uint16_t num_handles; /* number of handles to read */
uint16_t handles[GATT_MAX_READ_MULTI_HANDLES]; /* handles list to be read */
} tGATT_READ_MULTI;
/* Read By Handle Request (GATT_READ_BY_HANDLE) data */
typedef struct {
tGATT_AUTH_REQ auth_req;
uint16_t handle;
} tGATT_READ_BY_HANDLE;
/* READ_BT_HANDLE_Request data */
typedef struct {
tGATT_AUTH_REQ auth_req;
uint16_t handle;
uint16_t offset;
} tGATT_READ_PARTIAL;
/* Read Request Data
*/
typedef union {
tGATT_READ_BY_TYPE service;
tGATT_READ_BY_TYPE char_type; /* characterisitc type */
tGATT_READ_MULTI read_multiple;
tGATT_READ_BY_HANDLE by_handle;
tGATT_READ_PARTIAL partial;
} tGATT_READ_PARAM;
/* GATT write type enumeration */
enum { GATT_WRITE_NO_RSP = 1, GATT_WRITE, GATT_WRITE_PREPARE };
typedef uint8_t tGATT_WRITE_TYPE;
/* Client Operation Complete Callback Data
*/
typedef union {
tGATT_VALUE att_value;
uint16_t mtu;
uint16_t handle;
} tGATT_CL_COMPLETE;
/* GATT client operation type, used in client callback function
*/
#define GATTC_OPTYPE_NONE 0
#define GATTC_OPTYPE_DISCOVERY 1
#define GATTC_OPTYPE_READ 2
#define GATTC_OPTYPE_WRITE 3
#define GATTC_OPTYPE_EXE_WRITE 4
#define GATTC_OPTYPE_CONFIG 5
#define GATTC_OPTYPE_NOTIFICATION 6
#define GATTC_OPTYPE_INDICATION 7
typedef uint8_t tGATTC_OPTYPE;
/* characteristic declaration
*/
typedef struct {
tGATT_CHAR_PROP char_prop; /* characterisitc properties */
uint16_t val_handle; /* characteristic value attribute handle */
bluetooth::Uuid char_uuid; /* characteristic UUID type */
} tGATT_CHAR_DCLR_VAL;
/* primary service group data
*/
typedef struct {
uint16_t e_handle; /* ending handle of the group */
bluetooth::Uuid service_type; /* group type */
} tGATT_GROUP_VALUE;
/* included service attribute value
*/
typedef struct {
bluetooth::Uuid service_type; /* included service UUID */
uint16_t s_handle; /* starting handle */
uint16_t e_handle; /* ending handle */
} tGATT_INCL_SRVC;
typedef union {
tGATT_INCL_SRVC incl_service; /* include service value */
tGATT_GROUP_VALUE group_value; /* Service UUID type.
This field is used with GATT_DISC_SRVC_ALL
or GATT_DISC_SRVC_BY_UUID
type of discovery result callback. */
uint16_t handle; /* When used with GATT_DISC_INC_SRVC type discovery result,
it is the included service starting handle.*/
tGATT_CHAR_DCLR_VAL
dclr_value; /* Characteristic declaration value.
This field is used with GATT_DISC_CHAR type discovery.*/
} tGATT_DISC_VALUE;
/* discover result record
*/
typedef struct {
bluetooth::Uuid type;
uint16_t handle;
tGATT_DISC_VALUE value;
} tGATT_DISC_RES;
#define GATT_LINK_IDLE_TIMEOUT_WHEN_NO_APP \
1 /* start a idle timer for this duration \
when no application need to use the link */
#define GATT_LINK_NO_IDLE_TIMEOUT 0xFFFF
#define GATT_INVALID_ACL_HANDLE 0xFFFF
/* discover result callback function */
typedef void(tGATT_DISC_RES_CB)(uint16_t conn_id, tGATT_DISC_TYPE disc_type,
tGATT_DISC_RES* p_data);
/* discover complete callback function */
typedef void(tGATT_DISC_CMPL_CB)(uint16_t conn_id, tGATT_DISC_TYPE disc_type,
tGATT_STATUS status);
/* Define a callback function for when read/write/disc/config operation is
* completed. */
typedef void(tGATT_CMPL_CBACK)(uint16_t conn_id, tGATTC_OPTYPE op,
tGATT_STATUS status, tGATT_CL_COMPLETE* p_data);
/* Define a callback function when an initialized connection is established. */
typedef void(tGATT_CONN_CBACK)(tGATT_IF gatt_if, const RawAddress& bda,
uint16_t conn_id, bool connected,
tGATT_DISCONN_REASON reason,
tBT_TRANSPORT transport);
/* attribute request callback for ATT server */
typedef void(tGATT_REQ_CBACK)(uint16_t conn_id, uint32_t trans_id,
tGATTS_REQ_TYPE type, tGATTS_DATA* p_data);
/* channel congestion/uncongestion callback */
typedef void(tGATT_CONGESTION_CBACK)(uint16_t conn_id, bool congested);
/* Define a callback function when encryption is established. */
typedef void(tGATT_ENC_CMPL_CB)(tGATT_IF gatt_if, const RawAddress& bda);
/* Define a callback function when phy is updated. */
typedef void(tGATT_PHY_UPDATE_CB)(tGATT_IF gatt_if, uint16_t conn_id,
uint8_t tx_phy, uint8_t rx_phy,
uint8_t status);
/* Define a callback function when connection parameters are updated */
typedef void(tGATT_CONN_UPDATE_CB)(tGATT_IF gatt_if, uint16_t conn_id,
uint16_t interval, uint16_t latency,
uint16_t timeout, uint8_t status);
/* Define the structure that applications use to register with
* GATT. This structure includes callback functions. All functions
* MUST be provided.
*/
typedef struct {
tGATT_CONN_CBACK* p_conn_cb;
tGATT_CMPL_CBACK* p_cmpl_cb;
tGATT_DISC_RES_CB* p_disc_res_cb;
tGATT_DISC_CMPL_CB* p_disc_cmpl_cb;
tGATT_REQ_CBACK* p_req_cb;
tGATT_ENC_CMPL_CB* p_enc_cmpl_cb;
tGATT_CONGESTION_CBACK* p_congestion_cb;
tGATT_PHY_UPDATE_CB* p_phy_update_cb;
tGATT_CONN_UPDATE_CB* p_conn_update_cb;
} tGATT_CBACK;
/***************** Start Handle Management Definitions *********************/
typedef struct {
bluetooth::Uuid app_uuid128;
bluetooth::Uuid svc_uuid;
uint16_t s_handle;
uint16_t e_handle;
bool is_primary; /* primary service or secondary */
} tGATTS_HNDL_RANGE;
#define GATTS_SRV_CHG_CMD_ADD_CLIENT 1
#define GATTS_SRV_CHG_CMD_UPDATE_CLIENT 2
#define GATTS_SRV_CHG_CMD_REMOVE_CLIENT 3
#define GATTS_SRV_CHG_CMD_READ_NUM_CLENTS 4
#define GATTS_SRV_CHG_CMD_READ_CLENT 5
typedef uint8_t tGATTS_SRV_CHG_CMD;
typedef struct {
RawAddress bda;
bool srv_changed;
} tGATTS_SRV_CHG;
typedef union {
tGATTS_SRV_CHG srv_chg;
uint8_t client_read_index; /* only used for sequential reading client srv chg
info */
} tGATTS_SRV_CHG_REQ;
typedef union {
tGATTS_SRV_CHG srv_chg;
uint8_t num_clients;
} tGATTS_SRV_CHG_RSP;
/* Attibute server handle ranges NV storage callback functions
*/
typedef void(tGATTS_NV_SAVE_CBACK)(bool is_saved,
tGATTS_HNDL_RANGE* p_hndl_range);
typedef bool(tGATTS_NV_SRV_CHG_CBACK)(tGATTS_SRV_CHG_CMD cmd,
tGATTS_SRV_CHG_REQ* p_req,
tGATTS_SRV_CHG_RSP* p_rsp);
typedef struct {
tGATTS_NV_SAVE_CBACK* p_nv_save_callback;
tGATTS_NV_SRV_CHG_CBACK* p_srv_chg_callback;
} tGATT_APPL_INFO;
/******************** End Handle Management Definitions ********************/
/*******************************************************************************
* External Function Declarations
******************************************************************************/
/******************************************************************************/
/* GATT Profile API Functions */
/******************************************************************************/
/* GATT Profile Server Functions */
/******************************************************************************/
/*******************************************************************************
*
* Function GATTS_AddHandleRange
*
* Description This function add the allocated handles range for the
* specified application UUID, service UUID and service
* instance
*
* Parameter p_hndl_range: pointer to allocated handles information
******************************************************************************/
extern void GATTS_AddHandleRange(tGATTS_HNDL_RANGE* p_hndl_range);
/*******************************************************************************
*
* Function GATTS_NVRegister
*
* Description Application manager calls this function to register for
* NV save callback function. There can be one and only one
* NV save callback function.
*
* Parameter p_cb_info : callback informaiton
*
* Returns true if registered OK, else false
*
******************************************************************************/
extern bool GATTS_NVRegister(tGATT_APPL_INFO* p_cb_info);
/*******************************************************************************
*
* Function BTA_GATTS_AddService
*
* Description Add a service. When service is ready, a callback
* event BTA_GATTS_ADD_SRVC_EVT is called to report status
* and handles to the profile.
*
* Parameters server_if: server interface.
* service: pointer array describing service.
* count: number of elements in service array.
*
* Returns on success GATT_SERVICE_STARTED is returned, and
* attribute_handle field inside service elements are filled.
* on error error status is returned.
*
******************************************************************************/
extern uint16_t GATTS_AddService(tGATT_IF gatt_if, btgatt_db_element_t* service,
int count);
/*******************************************************************************
*
* Function GATTS_DeleteService
*
* Description This function is called to delete a service.
*
* Parameter gatt_if : application interface
* p_svc_uuid : service UUID
* svc_inst : instance of the service inside the
* application
*
* Returns true if operation succeed, else false
*
******************************************************************************/
extern bool GATTS_DeleteService(tGATT_IF gatt_if, bluetooth::Uuid* p_svc_uuid,
uint16_t svc_inst);
/*******************************************************************************
*
* Function GATTS_StopService
*
* Description This function is called to stop a service
*
* Parameter service_handle : this is the start handle of a service
*
* Returns None.
*
******************************************************************************/
extern void GATTS_StopService(uint16_t service_handle);
/*******************************************************************************
*
* Function GATTs_HandleValueIndication
*
* Description This function sends a handle value indication to a client.
*
* Parameter conn_id: connection identifier.
* attr_handle: Attribute handle of this handle value
* indication.
* val_len: Length of the indicated attribute value.
* p_val: Pointer to the indicated attribute value data.
*
* Returns GATT_SUCCESS if sucessfully sent or queued; otherwise error
* code.
*
******************************************************************************/
extern tGATT_STATUS GATTS_HandleValueIndication(uint16_t conn_id,
uint16_t attr_handle,
uint16_t val_len,
uint8_t* p_val);
/*******************************************************************************
*
* Function GATTS_HandleValueNotification
*
* Description This function sends a handle value notification to a client.
*
* Parameter conn_id: connection identifier.
* attr_handle: Attribute handle of this handle value
* indication.
* val_len: Length of the indicated attribute value.
* p_val: Pointer to the indicated attribute value data.
*
* Returns GATT_SUCCESS if sucessfully sent; otherwise error code.
*
******************************************************************************/
extern tGATT_STATUS GATTS_HandleValueNotification(uint16_t conn_id,
uint16_t attr_handle,
uint16_t val_len,
uint8_t* p_val);
/*******************************************************************************
*
* Function GATTS_SendRsp
*
* Description This function sends the server response to client.
*
* Parameter conn_id: connection identifier.
* trans_id: transaction id
* status: response status
* p_msg: pointer to message parameters structure.
*
* Returns GATT_SUCCESS if sucessfully sent; otherwise error code.
*
******************************************************************************/
extern tGATT_STATUS GATTS_SendRsp(uint16_t conn_id, uint32_t trans_id,
tGATT_STATUS status, tGATTS_RSP* p_msg);
/******************************************************************************/
/* GATT Profile Client Functions */
/******************************************************************************/
/*******************************************************************************
*
* Function GATTC_ConfigureMTU
*
* Description This function is called to configure the ATT MTU size for
* a connection on an LE transport.
*
* Parameters conn_id: connection identifier.
* mtu - attribute MTU size..
*
* Returns GATT_SUCCESS if command started successfully.
*
******************************************************************************/
extern tGATT_STATUS GATTC_ConfigureMTU(uint16_t conn_id, uint16_t mtu);
/*******************************************************************************
*
* Function GATTC_Discover
*
* Description This function is called to do a discovery procedure on ATT
* server.
*
* Parameters conn_id: connection identifier.
* disc_type:discovery type.
* start_handle and end_handle: range of handles for discovery
* uuid: uuid to discovery. set to Uuid::kEmpty for requests
* that don't need it
*
* Returns GATT_SUCCESS if command received/sent successfully.
*
******************************************************************************/
extern tGATT_STATUS GATTC_Discover(uint16_t conn_id, tGATT_DISC_TYPE disc_type,
uint16_t start_handle, uint16_t end_handle,
const bluetooth::Uuid& uuid);
extern tGATT_STATUS GATTC_Discover(uint16_t conn_id, tGATT_DISC_TYPE disc_type,
uint16_t start_handle, uint16_t end_handle);
/*******************************************************************************
*
* Function GATTC_Read
*
* Description This function is called to read the value of an attribute
* from the server.
*
* Parameters conn_id: connection identifier.
* type - attribute read type.
* p_read - read operation parameters.
*
* Returns GATT_SUCCESS if command started successfully.
*
******************************************************************************/
extern tGATT_STATUS GATTC_Read(uint16_t conn_id, tGATT_READ_TYPE type,
tGATT_READ_PARAM* p_read);
/*******************************************************************************
*
* Function GATTC_Write
*
* Description This function is called to read the value of an attribute
* from the server.
*
* Parameters conn_id: connection identifier.
* type - attribute write type.
* p_write - write operation parameters.
*
* Returns GATT_SUCCESS if command started successfully.
*
******************************************************************************/
extern tGATT_STATUS GATTC_Write(uint16_t conn_id, tGATT_WRITE_TYPE type,
tGATT_VALUE* p_write);
/*******************************************************************************
*
* Function GATTC_ExecuteWrite
*
* Description This function is called to send an Execute write request to
* the server.
*
* Parameters conn_id: connection identifier.
* is_execute - to execute or cancel the prepare write
* request(s)
*
* Returns GATT_SUCCESS if command started successfully.
*
******************************************************************************/
extern tGATT_STATUS GATTC_ExecuteWrite(uint16_t conn_id, bool is_execute);
/*******************************************************************************
*
* Function GATTC_SendHandleValueConfirm
*
* Description This function is called to send a handle value confirmation
* as response to a handle value notification from server.
*
* Parameters conn_id: connection identifier.
* handle: the handle of the attribute confirmation.
*
* Returns GATT_SUCCESS if command started successfully.
*
******************************************************************************/
extern tGATT_STATUS GATTC_SendHandleValueConfirm(uint16_t conn_id,
uint16_t handle);
/*******************************************************************************
*
* Function GATT_SetIdleTimeout
*
* Description This function (common to both client and server) sets the
* idle timeout for a tansport connection
*
* Parameter bd_addr: target device bd address.
* idle_tout: timeout value in seconds.
* transport: trasnport option.
*
* Returns void
*
******************************************************************************/
extern void GATT_SetIdleTimeout(const RawAddress& bd_addr, uint16_t idle_tout,
tGATT_TRANSPORT transport);
/*******************************************************************************
*
* Function GATT_Register
*
* Description This function is called to register an application
* with GATT
*
* Parameter p_app_uuid128: Application UUID
* p_cb_info: callback functions.
*
* Returns 0 for error, otherwise the index of the client registered
* with GATT
*
******************************************************************************/
extern tGATT_IF GATT_Register(const bluetooth::Uuid& p_app_uuid128,
tGATT_CBACK* p_cb_info);
/*******************************************************************************
*
* Function GATT_Deregister
*
* Description This function deregistered the application from GATT.
*
* Parameters gatt_if: applicaiton interface.
*
* Returns None.
*
******************************************************************************/
extern void GATT_Deregister(tGATT_IF gatt_if);
/*******************************************************************************
*
* Function GATT_StartIf
*
* Description This function is called after registration to start
* receiving callbacks for registered interface. Function may
* call back with connection status and queued notifications
*
* Parameter gatt_if: applicaiton interface.
*
* Returns None
*
******************************************************************************/
extern void GATT_StartIf(tGATT_IF gatt_if);
/*******************************************************************************
*
* Function GATT_Connect
*
* Description This function initiate a connecttion to a remote device on
* GATT channel.
*
* Parameters gatt_if: applicaiton interface
* bd_addr: peer device address.
* is_direct: is a direct connection or a background auto
* connection
* transport : Physical transport for GATT connection
* (BR/EDR or LE)
* opportunistic: will not keep device connected if other apps
* disconnect, will not update connected apps counter, when
* disconnected won't cause physical disconnection.
*
* Returns true if connection started; else false
*
******************************************************************************/
extern bool GATT_Connect(tGATT_IF gatt_if, const RawAddress& bd_addr,
bool is_direct, tBT_TRANSPORT transport,
bool opportunistic);
extern bool GATT_Connect(tGATT_IF gatt_if, const RawAddress& bd_addr,
bool is_direct, tBT_TRANSPORT transport,
bool opportunistic, uint8_t initiating_phys);
/*******************************************************************************
*
* Function GATT_CancelConnect
*
* Description Terminate the connection initiation to a remote device on a
* GATT channel.
*
* Parameters gatt_if: client interface. If 0 used as unconditionally
* disconnect, typically used for direct connection
* cancellation.
* bd_addr: peer device address.
* is_direct: is a direct conenection or a background auto
* connection
*
* Returns true if connection started; else false
*
******************************************************************************/
extern bool GATT_CancelConnect(tGATT_IF gatt_if, const RawAddress& bd_addr,
bool is_direct);
/*******************************************************************************
*
* Function GATT_Disconnect
*
* Description Disconnect the GATT channel for this registered application.
*
* Parameters conn_id: connection identifier.
*
* Returns GATT_SUCCESS if disconnected.
*
******************************************************************************/
extern tGATT_STATUS GATT_Disconnect(uint16_t conn_id);
/*******************************************************************************
*
* Function GATT_GetConnectionInfor
*
* Description Use conn_id to find its associated BD address and
* application interface
*
* Parameters conn_id: connection id (input)
* p_gatt_if: applicaiton interface (output)
* bd_addr: peer device address. (output)
* transport : physical transport of the GATT connection
* (BR/EDR or LE)
*
* Returns true the ligical link information is found for conn_id
*
******************************************************************************/
extern bool GATT_GetConnectionInfor(uint16_t conn_id, tGATT_IF* p_gatt_if,
RawAddress& bd_addr,
tBT_TRANSPORT* p_transport);
/*******************************************************************************
*
* Function GATT_GetConnIdIfConnected
*
* Description Find the conn_id if the logical link for a BD address
* and application interface is connected
*
* Parameters gatt_if: applicaiton interface (input)
* bd_addr: peer device address. (input)
* p_conn_id: connection id (output)
* transport : physical transport of the GATT connection
* (BR/EDR or LE)
*
* Returns true the ligical link is connected
*
******************************************************************************/
extern bool GATT_GetConnIdIfConnected(tGATT_IF gatt_if,
const RawAddress& bd_addr,
uint16_t* p_conn_id,
tBT_TRANSPORT transport);
/*******************************************************************************
*
* Function GATT_ConfigServiceChangeCCC
*
* Description Configure service change indication on remote device
*
* Returns None.
*
******************************************************************************/
extern void GATT_ConfigServiceChangeCCC(const RawAddress& remote_bda,
bool enable, tBT_TRANSPORT transport);
// Enables the GATT profile on the device.
// It clears out the control blocks, and registers with L2CAP.
extern void gatt_init(void);
// Frees resources used by the GATT profile.
extern void gatt_free(void);
// Link encryption complete notification for all encryption process
// initiated outside GATT.
extern void gatt_notify_enc_cmpl(const RawAddress& bd_addr);
/** Reset bg device list. If called after controller reset, set |after_reset| to
* true, as there is no need to wipe controller white list in this case. */
extern void gatt_reset_bgdev_list(bool after_reset);
#endif /* GATT_API_H */