Demonstrations of tcptop, the Linux eBPF/bcc version.
tcptop summarizes throughput by host and port. Eg:
# tcptop
Tracing... Output every 1 secs. Hit Ctrl-C to end
<screen clears>
19:46:24 loadavg: 1.86 2.67 2.91 3/362 16681
PID COMM LADDR RADDR RX_KB TX_KB
16648 16648 100.66.3.172:22 100.127.69.165:6684 1 0
16647 sshd 100.66.3.172:22 100.127.69.165:6684 0 2149
14374 sshd 100.66.3.172:22 100.127.69.165:25219 0 0
14458 sshd 100.66.3.172:22 100.127.69.165:7165 0 0
PID COMM LADDR6 RADDR6 RX_KB TX_KB
16681 sshd fe80::8a3:9dff:fed5:6b19:22 fe80::8a3:9dff:fed5:6b19:16606 1 1
16679 ssh fe80::8a3:9dff:fed5:6b19:16606 fe80::8a3:9dff:fed5:6b19:22 1 1
16680 sshd fe80::8a3:9dff:fed5:6b19:22 fe80::8a3:9dff:fed5:6b19:16606 0 0
This example output shows two listings of TCP connections, for IPv4 and IPv6.
If there is only traffic for one of these, then only one group is shown.
The output in each listing is sorted by total throughput (send then receive),
and when printed it is rounded (floor) to the nearest Kbyte. The example output
shows PID 16647, sshd, transmitted 2149 Kbytes during the tracing interval.
The other IPv4 sessions had such low throughput they rounded to zero.
All TCP sessions, including over loopback, are included.
The session with the process name (COMM) of 16648 is really a short-lived
process with PID 16648 where we didn't catch the process name when printing
the output. If this behavior is a serious issue for you, you can modify the
tool's code to include bpf_get_current_comm() in the key structs, so that it's
fetched during the event and will always be seen. I did it this way to start
with, but it was measurably increasing the overhead of this tool, so I switched
to the asynchronous model.
The overhead is relative to TCP event rate (the rate of tcp_sendmsg() and
tcp_recvmsg() or tcp_cleanup_rbuf()). Due to buffering, this should be lower
than the packet rate. You can measure the rate of these using funccount.
Some sample production servers tested found total rates of 4k to 15k per
second. The CPU overhead at these rates ranged from 0.5% to 2.0% of one CPU.
Maybe your workloads have higher rates and therefore higher overhead, or,
lower rates.
I much prefer not clearing the screen, so that historic output is in the
scroll-back buffer, and patterns or intermittent issues can be better seen.
You can do this with -C:
# tcptop -C
Tracing... Output every 1 secs. Hit Ctrl-C to end
20:27:12 loadavg: 0.08 0.02 0.17 2/367 17342
PID COMM LADDR RADDR RX_KB TX_KB
17287 17287 100.66.3.172:22 100.127.69.165:57585 3 1
17286 sshd 100.66.3.172:22 100.127.69.165:57585 0 1
14374 sshd 100.66.3.172:22 100.127.69.165:25219 0 0
20:27:13 loadavg: 0.08 0.02 0.17 1/367 17342
PID COMM LADDR RADDR RX_KB TX_KB
17286 sshd 100.66.3.172:22 100.127.69.165:57585 1 7761
14374 sshd 100.66.3.172:22 100.127.69.165:25219 0 0
20:27:14 loadavg: 0.08 0.02 0.17 2/365 17347
PID COMM LADDR RADDR RX_KB TX_KB
17286 17286 100.66.3.172:22 100.127.69.165:57585 1 2501
14374 sshd 100.66.3.172:22 100.127.69.165:25219 0 0
20:27:15 loadavg: 0.07 0.02 0.17 2/367 17403
PID COMM LADDR RADDR RX_KB TX_KB
17349 17349 100.66.3.172:22 100.127.69.165:10161 3 1
17348 sshd 100.66.3.172:22 100.127.69.165:10161 0 1
14374 sshd 100.66.3.172:22 100.127.69.165:25219 0 0
20:27:16 loadavg: 0.07 0.02 0.17 1/367 17403
PID COMM LADDR RADDR RX_KB TX_KB
17348 sshd 100.66.3.172:22 100.127.69.165:10161 3333 0
14374 sshd 100.66.3.172:22 100.127.69.165:25219 0 0
20:27:17 loadavg: 0.07 0.02 0.17 2/366 17409
PID COMM LADDR RADDR RX_KB TX_KB
17348 17348 100.66.3.172:22 100.127.69.165:10161 6909 2
You can disable the loadavg summary line with -S if needed.
USAGE:
# tcptop -h
usage: tcptop.py [-h] [-C] [-S] [-p PID] [interval] [count]
Summarize TCP send/recv throughput by host
positional arguments:
interval output interval, in seconds (default 1)
count number of outputs
optional arguments:
-h, --help show this help message and exit
-C, --noclear don't clear the screen
-S, --nosummary skip system summary line
-p PID, --pid PID trace this PID only
examples:
./tcptop # trace TCP send/recv by host
./tcptop -C # don't clear the screen
./tcptop -p 181 # only trace PID 181