C++程序
|
4674行
|
157.33 KB
/*
* TWDriver.h
*
* Copyright(c) 1998 - 2009 Texas Instruments. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name Texas Instruments nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/** \file TWDriver.h
* \brief TWDriver APIs
*
* \see
*/
/** @defgroup Control Control group
* \brief The Control group includes the list of functions which perform TWD Control
*/
/** @defgroup Measurement Measurement group
* \brief The Measurement group includes the list of functions which gets measurements from FW / TWD
*/
/** @defgroup Data_Path Data Path group
* \brief The Data Path group includes the list of functions which perform the TWD Data Path
*/
/** @defgroup Power_Management Power Management group
* \brief The Power Management group includes the list of functions which set the power management mode
*/
/** @defgroup QoS Quality Of Service group
* \brief The Quality of Service group includes the list of functions which perform the TWD QoS
*/
/** @defgroup Radio Radio (PHY) group
* \brief The Radio group includes the list of functions which handle the Radio
*/
/** @defgroup BSS BSS group
* \brief The BSS group includes the list of functions which handle the Basic Service Set
*/
/** @defgroup Misc Miscellaneous group
* \brief The Miscellaneous group includes the list of functions which handle miscellaneous issues
*/
#ifdef TI_DBG
/** @defgroup Test Debug Test group
* \brief The Debug Test group includes the list of functions which Test the TWD and FW
*/
#endif
#ifndef TWDRIVER_H
#define TWDRIVER_H
#define MAX_NUM_OF_802_1d_TAGS 8
#include "802_11Defs.h"
#include "TWDriverMsr.h"
#include "TWDriverScan.h"
#include "TWDriverRate.h"
#include "fwDebug_api.h"
#include "TwIf.h"
/*
* original firmware h-files
*/
#include "public_commands.h"
#include "public_event_mbox.h"
#include "public_infoele.h"
#include "public_host_int.h"
#include "public_descriptors.h"
#include "public_radio.h"
/*
* Firmware types defintions
*/
#ifndef uint8
#define uint8 TI_UINT8
#endif
#ifndef uint16
#define uint16 TI_UINT16
#endif
#ifndef uint32
#define uint32 TI_UINT32
#endif
#ifndef int8
#define int8 TI_INT8
#endif
#ifndef int16
#define int16 TI_INT16
#endif
#ifndef int32
#define int32 TI_INT32
#endif
/*
* --------------------------------------------------------------
* Definitions
* --------------------------------------------------------------
*/
/* PALAU Group Address Default Values */
#define NUM_GROUP_ADDRESS_VALUE_DEF 4
#define NUM_GROUP_ADDRESS_VALUE_MIN 0
#define NUM_GROUP_ADDRESS_VALUE_MAX 8
/* Early Wakeup Default Values */
#define EARLY_WAKEUP_ENABLE_MIN (TI_FALSE)
#define EARLY_WAKEUP_ENABLE_MAX (TI_TRUE)
#define EARLY_WAKEUP_ENABLE_DEF (TI_TRUE)
/* ARP IP Filter Default Values */
#define MIN_FILTER_ENABLE_VALUE 0
#define MAX_FILTER_ENABLE_VALUE 2
#define DEF_FILTER_ENABLE_VALUE 0
#define FILTER_ENABLE_FLAG_LEN 1
/* Beacon filter Deafult Values */
#define DEF_BEACON_FILTER_ENABLE_VALUE 1
#define DEF_BEACON_FILTER_IE_TABLE_NUM 16
#define MIN_BEACON_FILTER_ENABLE_VALUE 0
#define MAX_BEACON_FILTER_ENABLE_VALUE 1
#define BEACON_FILTER_IE_TABLE_DEF_SIZE 37
#define BEACON_FILTER_IE_TABLE_MAX_SIZE 100
#define BEACON_FILTER_IE_TABLE_MIN_SIZE 0
#define BEACON_FILTER_IE_TABLE_MAX_NUM (6+32)
#define BEACON_FILTER_IE_TABLE_MIN_NUM 0
/* CoexActivity Table Deafult Values */
#define COEX_ACTIVITY_TABLE_DEF_NUM 0
#define COEX_ACTIVITY_TABLE_MIN_NUM 0
#define COEX_ACTIVITY_TABLE_MAX_NUM 24*2
#define COEX_ACTIVITY_TABLE_SIZE ((2+1)+(2+1)+(2+1)+(2+1)+(4+1)+(4+1)) /* includes spaces between bytes */
#define DEF_NUM_STORED_FILTERS 1
#define MIN_NUM_STORED_FILTERS 1
#define MAX_NUM_STORED_FILTERS 8
#define TWD_HW_ACCESS_METHOD_MIN 0
#define TWD_HW_ACCESS_METHOD_MAX 2
#define TWD_HW_ACCESS_METHOD_DEF 1
#define TWD_SITE_FRAG_COLLECT_MIN 2
#define TWD_SITE_FRAG_COLLECT_MAX 10
#define TWD_SITE_FRAG_COLLECT_DEF 3
#define TWD_RX_MEM_BLKS_NUM 64 /* The number of Rx memory blocks configured to FW */
#define TWD_TX_MIN_MEM_BLKS_NUM 64 /* The MINIMUM number of Tx memory blocks configured to FW */
#define TWD_RX_BLOCKS_RATIO_MIN 0
#define TWD_RX_BLOCKS_RATIO_MAX 100
#define TWD_RX_BLOCKS_RATIO_DEF 50
#define TWD_TX_FLASH_ENABLE_MIN TI_FALSE
#define TWD_TX_FLASH_ENABLE_MAX TI_TRUE
#define TWD_TX_FLASH_ENABLE_DEF TI_TRUE
#define TWD_USE_INTR_TRHESHOLD_MIN 0
#define TWD_USE_INTR_TRHESHOLD_MAX 1
#define TWD_USE_INTR_TRHESHOLD_DEF 0
#define TWD_USE_TX_DATA_INTR_MIN 0
#define TWD_USE_TX_DATA_INTR_MAX 1
#define NUM_OF_CHANNELS_24 14
#define NUM_OF_CHANNELS_5 180
#define TWD_CALIBRATION_CHANNEL_2_4_MIN 1
#define TWD_CALIBRATION_CHANNEL_2_4_MAX NUM_OF_CHANNELS_24
#define TWD_CALIBRATION_CHANNEL_2_4_DEF 1
#define A_5G_BAND_MIN_CHANNEL 36
#define A_5G_BAND_MAX_CHANNEL 180
#define A_5G_BAND_NUM_CHANNELS (A_5G_BAND_MAX_CHANNEL-A_5G_BAND_MIN_CHANNEL+1)
#define TWD_CALIBRATION_CHANNEL_5_0_MIN 34
#define TWD_CALIBRATION_CHANNEL_5_0_MAX A_5G_BAND_MAX_CHANNEL
#define TWD_CALIBRATION_CHANNEL_5_0_DEF 36
#define TWD_CALIBRATION_CHANNEL_4_9_MIN 8
#define TWD_CALIBRATION_CHANNEL_4_9_MAX 16
#define TWD_CALIBRATION_CHANNEL_4_9_DEF 12
#define TWD_RTS_THRESHOLD_MIN 0
#define TWD_RTS_THRESHOLD_MAX 4096
#define TWD_RTS_THRESHOLD_DEF 4096
#define TWD_BCN_RX_TIME_OUT_MIN 10 /* ms */
#define TWD_BCN_RX_TIME_OUT_MAX 1000 /* ms */
#define TWD_BCN_RX_TIME_OUT_DEF 10 /* ms */
#define TWD_RX_DISABLE_BROADCAST_MIN TI_FALSE
#define TWD_RX_DISABLE_BROADCAST_MAX TI_TRUE
#define TWD_RX_DISABLE_BROADCAST_DEF TI_FALSE
/* Indicate if the recovery process is active or not */
#define TWD_RECOVERY_ENABLE_MIN TI_FALSE
#define TWD_RECOVERY_ENABLE_MAX TI_TRUE
#define TWD_RECOVERY_ENABLE_DEF TI_TRUE
/* Indicate if working with Burst Mode or not */
#define BURST_MODE_ENABLE_MIN TI_FALSE
#define BURST_MODE_ENABLE_MAX TI_TRUE
#define BURST_MODE_ENABLE_DEF TI_FALSE
#define SMART_REFLEX_STATE_MIN TI_FALSE
#define SMART_REFLEX_STATE_MAX TI_TRUE
#define SMART_REFLEX_STATE_DEF TI_TRUE
#define SMART_REFLEX_DEBUG_MIN 0
#define SMART_REFLEX_DEBUG_MAX 0xFFFF
#define SMART_REFLEX_DEBUG_DEF 0
#define SMART_REFLEX_CONFIG_PARAMS_DEF_TABLE "0,0,0,0,0,0,0,0,0,0,0,0,0,0"
#define TWD_FRAG_THRESHOLD_MIN 256
#define TWD_FRAG_THRESHOLD_MAX 4096
#define TWD_FRAG_THRESHOLD_DEF 4096
#define TWD_MAX_TX_MSDU_LIFETIME_MIN 0
#define TWD_MAX_TX_MSDU_LIFETIME_MAX 3000
#define TWD_MAX_TX_MSDU_LIFETIME_DEF 512
#define TWD_MAX_RX_MSDU_LIFETIME_MIN 0
#define TWD_MAX_RX_MSDU_LIFETIME_MAX 0xFFFFFFFF
#define TWD_MAX_RX_MSDU_LIFETIME_DEF 512000
#define TWD_LISTEN_INTERVAL_MIN 1
#define TWD_LISTEN_INTERVAL_MAX 10
#define TWD_LISTEN_INTERVAL_DEF 3
/* This field indicates the number of transmit retries to attempt at
the rate specified in the TNETW Tx descriptor before
falling back to the next lowest rate.
If this field is set to 0xff, then rate fallback is disabled.
If this field is 0, then there will be 0 retries before starting fallback.*/
#define TWD_RATE_FB_RETRY_LIMIT_MIN 0 /* => No retries before starting RateFallBack */
#define TWD_RATE_FB_RETRY_LIMIT_MAX 255 /* =>0xff for disabling Rate fallback */
#define TWD_RATE_FB_RETRY_LIMIT_DEF 0
#define TWD_TX_ANTENNA_MIN TX_ANTENNA_2
#define TWD_TX_ANTENNA_MAX TX_ANTENNA_1
#define TWD_TX_ANTENNA_DEF TX_ANTENNA_1
#define TWD_RX_ANTENNA_MIN RX_ANTENNA_1
#define TWD_RX_ANTENNA_MAX RX_ANTENNA_PARTIAL
#define TWD_RX_ANTENNA_DEF RX_ANTENNA_FULL
/*
* Tx and Rx interrupts pacing (threshold in packets, timeouts in milliseconds)
*/
#define TWD_TX_CMPLT_THRESHOLD_DEF 4 /* 0 means no pacing so send interrupt on every event */
#define TWD_TX_CMPLT_THRESHOLD_MIN 0
#define TWD_TX_CMPLT_THRESHOLD_MAX 30
#define TWD_TX_CMPLT_TIMEOUT_DEF 5
#define TWD_TX_CMPLT_TIMEOUT_MIN 1
#define TWD_TX_CMPLT_TIMEOUT_MAX 100
#define TWD_RX_INTR_THRESHOLD_DEF 0 /* 0 means no pacing so send interrupt on every event */
#define TWD_RX_INTR_THRESHOLD_MIN 0
#define TWD_RX_INTR_THRESHOLD_MAX 30
#define TWD_RX_INTR_THRESHOLD_DEF_WIFI_MODE 0 /* No Rx interrupt pacing so send interrupt on every event */
#define TWD_RX_INTR_TIMEOUT_DEF 1
#define TWD_RX_INTR_TIMEOUT_MIN 1
#define TWD_RX_INTR_TIMEOUT_MAX 100
/* Rx aggregation packets number limit (max packets in one aggregation) */
#define TWD_RX_AGGREG_PKTS_LIMIT_DEF 4
#define TWD_RX_AGGREG_PKTS_LIMIT_MIN 1
#define TWD_RX_AGGREG_PKTS_LIMIT_MAX 4
/*
* Tx power level
*/
#define DBM_TO_TX_POWER_FACTOR 10
/* TX_POWER is in Dbm/10 units */
#define MAX_TX_POWER 250
#define MIN_TX_POWER 0
#define DEF_TX_POWER 205
#define MIN_DEFAULT_KEY_ID 0
#define MAX_DEFAULT_KEY_ID 3
#define KEY_RSC_LEN 8
#define MIN_KEY_LEN 5
#define MAX_KEY_LEN 32
#define TWD_RSSI_BEACON_WEIGHT_MIN 0
#define TWD_RSSI_BEACON_WEIGHT_MAX 100
#define TWD_RSSI_BEACON_WEIGHT_DEF 20
#define TWD_RSSI_PACKET_WEIGHT_MIN 0
#define TWD_RSSI_PACKET_WEIGHT_MAX 100
#define TWD_RSSI_PACKET_WEIGHT_DEF 10
#define TWD_SNR_BEACON_WEIGHT_MIN 0
#define TWD_SNR_BEACON_WEIGHT_MAX 100
#define TWD_SNR_BEACON_WEIGHT_DEF 20
#define TWD_SNR_PACKET_WEIGHT_MIN 0
#define TWD_SNR_PACKET_WEIGHT_MAX 100
#define TWD_SNR_PACKET_WEIGHT_DEF 10
#define MAX_NUM_OF_AC 4
/************************************/
/* Rates values */
/************************************/
/* The next definitions are used to decide which encryption is used by the Rx flags */
#define RX_FLAGS_NO_SECURITY 0
#define RX_FLAGS_WEP 1
#define RX_FLAGS_TKIP 2
#define RX_FLAGS_AES 3
#define RX_DESC_FLAGS_ENCRYPTION 8
#define RX_PACKET_FLAGS_ENCRYPTION_SHIFT 16
#define RX_PACKET_FLAGS_ENCRYPTION_SHIFT_FROM_DESC (RX_PACKET_FLAGS_ENCRYPTION_SHIFT - RX_DESC_FLAGS_ENCRYPTION)
/* Tx packet Control-Block flags bit-mask. */
#define TX_CTRL_FLAG_XFER_DONE_ISSUED 0x0001 /* Xfer-Done already issued to upper driver - for WHA. */
#define TX_CTRL_FLAG_TX_COMPLETE_ISSUED 0x0002 /* Tx-Complete already issued to upper driver - for WHA. */
#define TX_CTRL_FLAG_LINK_TEST 0x0004 /* XCC link test packet */
#define TX_CTRL_FLAG_SENT_TO_FW 0x0008 /* Set after the packet is allowed to be sent to FW (by TxHwQueue) */
#define TX_CTRL_FLAG_PKT_IN_RAW_BUF 0x0010 /* The input packet is in a raw buffer (as opposed to OS packet) */
#define TX_CTRL_FLAG_MULTICAST 0x0020 /* A multicast ethernet packet */
#define TX_CTRL_FLAG_BROADCAST 0x0040 /* A broadcast ethernet packet */
#define TX_PKT_TYPE_MGMT 1 /* Management Packet */
#define TX_PKT_TYPE_EAPOL 2 /* EAPOL packet (Ethernet) */
#define TX_PKT_TYPE_ETHER 3 /* Data packet from the Network interface */
#define TX_PKT_TYPE_WLAN_DATA 4 /* Driver generated WLAN Data Packet (currently used for IAPP packet) */
#define ALIGN_4BYTE_MASK 0x3 /* Masked LS bits for 4-bytes aligned addresses or lengths. */
#define SHIFT_BETWEEN_TU_AND_USEC 10 /* Shift factor to convert between TU (1024 uSec) and uSec. */
/* Packet header + extensions structure ranges between 24 and 48 bytes as follows:
* ------------------------------------------------------------------------------
* Alignment Padding: 0/2 bytes, added for 4 bytes alignment of this structure.
* Mac-Header: 24 bytes, 802.11 basic header.
* Qos header: 0/2 bytes, for QoS-data or QoS-Null the two QoS bytes are added.
* Security Pad: 0/0/4/8 bytes, for None/WEP/TKIP/AES.
* LLC/SNAP: 0/8 bytes, added only for data packets.
* HT control: 0/4 added only for packte support QoS and HT
*/
#define MAX_HEADER_SIZE 48
/* Data body max length */
#define MAX_DATA_BODY_LENGTH 4096
/* The weight in % of the new packet relative to the previous average value of RSSI */
#define RSSI_DEFAULT_WEIGHT 20
#define RSSI_DEFAULT_THRESHOLD -80
#define SNR_DEFAULT_THRESHOLD 0
/*
* 'No beacon' roaming trigger configuration
* Number of consecutive beacons (or DTIM periods) missed before
* 'Out of Sync' event is raised
*/
#define OUT_OF_SYNC_DEFAULT_THRESHOLD 10
/*
* IBSS - Number of consecutive beacons (or DTIM periods) missed before
* 'Out of Sync' event is raised
*/
#define OUT_OF_SYNC_IBSS_THRESHOLD 200
/* Period of time between 'Out of sync' and 'No beacon' events */
#define NO_BEACON_DEFAULT_TIMEOUT 100 /* in tu-s*/
/* Consecutive NACK roaming trigger configuration */
#define NO_ACK_DEFAULT_THRESHOLD 20
/* Low Rx rate roaming trigger configuration */
#define LOW_RATE_DEFAULT_THRESHOLD 2
#define MEASUREMENT_NOISE_HISTOGRAM_NUM_OF_RANGES 8
#define MAX_CHANNELS_IN_REG_DOMAIN 40
#define CTS_TO_SELF_DISABLE 0
#define CTS_TO_SELF_ENABLE 1
#define MAX_TEMPLATE_SIZE 256
/* Scan constants */
#define MAX_NUMBER_OF_CHANNELS_PER_SCAN 16
#define SCAN_MAX_NUM_OF_NORMAL_CHANNELS_PER_COMMAND MAX_NUMBER_OF_CHANNELS_PER_SCAN
#define SCAN_MAX_NUM_OF_SPS_CHANNELS_PER_COMMAND 16
#define SCAN_DEFAULT_MIN_CHANNEL_DWELL_TIME 30000
#define SCAN_DEFAULT_MAX_CHANNEL_DWELL_TIME 60000
#define SCAN_DEFAULT_EARLY_TERMINATION_EVENT SCAN_ET_COND_DISABLE
#define SCAN_DEFAULT_EARLY_TERMINATION_NUM_OF_FRAMES 0
#define NUM_OF_NOISE_HISTOGRAM_COUNTERS 8
#define TX_DESCRIPTOR_SIZE sizeof(TxIfDescriptor_t)
#define CTRL_BLK_ENTRIES_NUM 128
#define HT_CAP_AMPDU_PARAMETERS_FIELD_OFFSET 2
#define HT_CAP_HT_EXTENDED_FIELD_OFFSET 19
#define HT_CAP_AMPDU_MAX_RX_FACTOR_BITMASK 0x3
#define HT_CAP_AMPDU_MIN_START_SPACING_BITMASK 0x7
#define HT_CAP_GREENFIELD_FRAME_FORMAT_BITMASK 0x0010
#define HT_CAP_SHORT_GI_FOR_20MHZ_BITMASK 0x0020
#define HT_CAP_LSIG_TXOP_PROTECTION_BITMASK 0x8000
#define HT_EXT_HT_CONTROL_FIELDS_BITMASK 0x0400
#define HT_EXT_RD_INITIATION_BITMASK 0x0800
#define HT_INF_RIFS_MOD_BITMASK 0x08
#define HT_INF_OPERATION_MOD_BITMASK 0x03
#define HT_INF_NON_GF_PRES_BITMASK 0x04
#define HT_INF_TX_BURST_LIMIT_BITMASK 0x08
#define HT_INF_DUAL_BEACON_BITMASK 0x40
/*
* TWD HT capabilities, physical capabilities of the STA.
* The structure is defined like that in order to simplify the interface with WHA layer.
*/
#define RX_TX_MCS_BITMASK_SIZE 10
#define DSSS_CCK_MODE 1
#define MCS_HIGHEST_SUPPORTED_RECEPTION_DATA_RATE_IN_MBIT_S 0x48
#define IMPLICIT_TXBF_REC_CAPABLE 1
#define TRANSMIT_STAGGERED_SOUNDING_CAPABLE 1
/* Firmware version name length */
#define FW_VERSION_LEN 20
/*the max table sized is : ( number of 221 * 8 bytes ) + ( non-221 * 2 bytes )
Must be synchronized with the size of ACX defined in public_infoele.h interface
with the FW
*/
#define MIB_MAX_SIZE_OF_IE_TABLE 112
#define MIB_TEMPLATE_DATA_MAX_LEN 256
#define MIB_MAX_MULTICAST_GROUP_ADDRS 8
#define MAX_MULTICAST_GROUP_ADDRS 8
/* Max numver of policies */
#define MAX_NUM_OF_TX_RATE_CLASS_POLICIES 8
#define NUM_POWER_LEVELS 4
#define MAX_POWER_LEVEL 1
#define MIN_POWER_LEVEL NUM_POWER_LEVELS
/*
* --------------------------------------------------------------
* Enumerations
* --------------------------------------------------------------
*/
/** \enum EFileType
* \brief TWD input/output files
*
* \par Description
* Indicates which File (or part of file) to read or write
*
* \sa TFileInfo
*/
typedef enum
{
FILE_TYPE_INI = 0, /**< */
FILE_TYPE_NVS, /**< */
FILE_TYPE_FW, /**< */
FILE_TYPE_FW_NEXT /**< */
} EFileType;
/** \enum EKeepAliveTriggerType
* \brief Keep Alive Trigger Types
*
* \par Description
* Indicates when to trigger Keep Alive
*
* \sa TKeepAliveParams
*
*/
typedef enum
{
KEEP_ALIVE_TRIG_TYPE_NO_TX = 0, /**< */
KEEP_ALIVE_TRIG_TYPE_PERIOD_ONLY /**< */
} EKeepAliveTriggerType;
/** \enum ESlotTime
* \brief Radio (PHY) Slot Time Type
*
* \par Description
* Used for configuring PHY Slot Time for FW
*
* \sa TWD_CfgPreamble
*/
typedef enum
{
PHY_SLOT_TIME_LONG = 0, /**< Long PHY Slot Time */
PHY_SLOT_TIME_SHORT = 1 /**< Short PHY Slot Time */
} ESlotTime;
/** \enum EMib
* \brief MIB Element Type
*
* \par Description
* Used for R/W MIB to FW
*
* \sa TMib
*/
typedef enum
{
/* 0x00 */ MIB_dot11MaxReceiveLifetime = 0, /**< */
/* 0x01 */ MIB_dot11SlotTime, /**< */
/* 0x02 */ MIB_dot11GroupAddressesTable, /**< */
/* 0x03 */ MIB_dot11WepDefaultKeyId, /**< */
/* 0x04 */ MIB_dot11CurrentTxPowerLevel, /**< */
/* 0x05 */ MIB_dot11RTSThreshold, /**< */
/* 0x06 */ MIB_ctsToSelf, /**< */
/* 0x07 */ MIB_arpIpAddressesTable, /**< */
/* 0x08 */ MIB_templateFrame, /**< */
/* 0x09 */ MIB_rxFilter, /**< */
/* 0x0A */ MIB_beaconFilterIETable, /**< */
/* 0x0B */ MIB_beaconFilterEnable, /**< */
/* 0x0C */ MIB_sleepMode, /**< */
/* 0x0D */ MIB_wlanWakeUpInterval, /**< */
/* 0x0E */ MIB_beaconLostCount, /**< */
/* 0x0F */ MIB_rcpiThreshold, /**< */
/* 0x10 */ MIB_statisticsTable, /**< */
/* 0x11 */ MIB_ibssPsConfig, /**< */
/* 0x12 */ MIB_txRatePolicy, /**< */
/* 0x13 */ MIB_countersTable, /**< */
/* 0x14 */ MIB_btCoexsitenceMode, /**< */
/* 0x15 */ MIB_btCoexistenceParameters, /**< */
/* must be last!!! */
MIB_lastElem = 0xFFFF /**< */
} EMib;
/** \enum ETwdParam
* \brief TWD Control parameter ID
*
* \par Description
* FW Parmaeter Information Identifier
*
* \sa TWD_SetParam, TWD_GetParam
*/
typedef enum
{
/* 0x01 */ TWD_RTS_THRESHOLD_PARAM_ID = 0x01, /**< */
/* 0x02 */ TWD_FRAG_THRESHOLD_PARAM_ID, /**< */
/* 0x03 */ TWD_COUNTERS_PARAM_ID, /**< */
/* 0x04 */ TWD_LISTEN_INTERVAL_PARAM_ID, /**< */
/* 0x05 */ TWD_BEACON_INTERVAL_PARAM_ID, /**< */
/* 0x06 */ TWD_TX_POWER_PARAM_ID, /**< */
/* 0x07 */ TWD_CLK_RUN_ENABLE_PARAM_ID, /**< */
/* 0x08 */ TWD_QUEUES_PARAM_ID, /**< */
/* 0x09 */ TWD_TX_RATE_CLASS_PARAM_ID, /**< */
/* 0x0A */ TWD_MAX_TX_MSDU_LIFE_TIME_PARAM_ID, /**< */
/* 0x0B */ TWD_MAX_RX_MSDU_LIFE_TIME_PARAM_ID, /**< */
/* 0x0C */ TWD_CTS_TO_SELF_PARAM_ID, /**< */
/* 0x0D */ TWD_RX_TIME_OUT_PARAM_ID, /**< */
/* 0x0E */ TWD_BCN_BRC_OPTIONS_PARAM_ID, /**< */
/* 0x0F */ TWD_AID_PARAM_ID, /**< */
/* 0x10 */ TWD_RSN_HW_ENC_DEC_ENABLE_PARAM_ID, /**< */
/* 0x11 */ TWD_RSN_KEY_ADD_PARAM_ID, /**< */
/* 0x12 */ TWD_RSN_KEY_REMOVE_PARAM_ID, /**< */
/* 0x13 */ TWD_RSN_DEFAULT_KEY_ID_PARAM_ID, /**< */
/* 0x14 */ TWD_RSN_SECURITY_MODE_PARAM_ID, /**< */
/* 0x15 */ TWD_RSN_SECURITY_ALARM_CB_SET_PARAM_ID, /**< */
/* 0x16 */ TWD_ACX_STATISTICS_PARAM_ID, /**< */
/* 0x17 */ TWD_MEDIUM_OCCUPANCY_PARAM_ID, /**< */
/* 0x18 */ TWD_DISABLE_POWER_MANAGEMENT_AUTO_CONFIG_PARAM_ID, /**< */
/* 0x19 */ TWD_ENABLE_POWER_MANAGEMENT_AUTO_CONFIG_PARAM_ID, /**< */
/* 0x1A */ TWD_SG_ENABLE_PARAM_ID, /**< */
/* 0x1B */ TWD_SG_CONFIG_PARAM_ID, /**< */
#ifdef XCC_MODULE_INCLUDED
/* 0x1C */ TWD_RSN_XCC_SW_ENC_ENABLE_PARAM_ID, /**< */
/* 0x1D */ TWD_RSN_XCC_MIC_FIELD_ENABLE_PARAM_ID, /**< */
#endif /* XCC_MODULE_INCLUDED*/
/* 0x1E */ TWD_TX_OP_LIMIT_PARAM_ID, /**< */
/* 0x1F */ TWD_NOISE_HISTOGRAM_PARAM_ID, /**< */
/* 0x20 */ TWD_TSF_DTIM_MIB_PARAM_ID, /**< */
/* 0x21 */ TWD_REVISION_PARAM_ID, /**< */
/* 0x22 */ TWD_CURRENT_CHANNEL_PARAM_ID, /**< */
/* 0x23 */ TWD_RADIO_TEST_PARAM_ID, /**< */
/* 0x24 */ TWD_RSSI_LEVEL_PARAM_ID, /**< */
/* 0x25 */ TWD_SNR_RATIO_PARAM_ID, /**< */
/* 0x26 */ TWD_COEX_ACTIVITY_PARAM_ID, /**< */
/* 0x27 */ TWD_FM_COEX_PARAM_ID, /**< */
/* must be last!!! */
/* 0x28 */ TWD_LAST_PARAM_ID /**< */
} ETwdParam;
/** \enum ETwdCallbackOwner
* \brief TWD Callback Module owner ID
*
* \par Description
* The Owner ID defines a specific TWD Module
*
* \sa ETwdEventId, TWD_RegisterCb
*/
typedef enum
{
TWD_OWNER_DRIVER_TX_XFER = 0x0100, /**< TX Xfer Owner ID */
TWD_OWNER_RX_XFER = 0x0200, /**< RX Xfer Owner ID */
TWD_OWNER_SELF = 0x0300, /**< Self Owner ID */
TWD_OWNER_MAC_SERVICES = 0x0400, /**< MAC Services Owner ID */
TWD_OWNER_TX_RESULT = 0x0500, /**< TX Result Owner ID */
TWD_OWNER_SELF_CONFIG = 0x0600, /**< Self configuration of Owner ID */
TWD_OWNER_RX_QUEUE = 0x0700, /**< RX Queue Owner ID */
TWD_OWNER_TX_HW_QUEUE = 0x0800 /**< TX HW Queue Owner ID */
} ETwdCallbackOwner;
/** \enum ETwdIntCallbackId
* \brief TWD Internal Callbacks ID
*
* \par Description
* The Owner ID defines a specific TWD Internal CB
*
* \sa ETwdEventId
*/
typedef enum
{
TWD_INT_SEND_PACKET_TRANSFER = 0x00 , /**< Tx Data Path Send Callback */
TWD_INT_SEND_PACKET_COMPLETE , /**< Tx Data Path Complete Callback */
TWD_INT_UPDATE_BUSY_MAP , /**< Tx Data Path Update-Busy-Map Callback */
/* Rx Data Path Callbacks */
TWD_INT_RECEIVE_PACKET = 0x10 , /**< Rx Data Path Receive Packet Callback */
TWD_INT_REQUEST_FOR_BUFFER , /**< Rx Data Path Request for buffer Callback */
/* TWD Callbacks */
TWD_INT_COMMAND_COMPLETE = 0x20 , /**< TWD internal Command Complete Callback */
TWD_INT_EVENT_FAILURE /**< TWD internal Event Failure handle Callback */
} ETwdIntCallbackId;
/** \enum ETwdOwnEventId
* \brief Event Mail Box ID
*
* \par Description
* Clients That expects an event should register for it,
* and Mask/UnMask Events with this ID
*
* \sa
*/
/* Note: changes here should be reflected also in eventTable in eventMbox.c !!! */
typedef enum
{
/*Regular events*/
/* 0 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_0 = 0, /**< */
/* 1 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_1, /**< */
/* 2 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_2, /**< */
/* 3 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_3, /**< */
/* 4 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_4, /**< */
/* 5 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_5, /**< */
/* 6 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_6, /**< */
/* 7 */ TWD_OWN_EVENT_RSSI_SNR_TRIGGER_7, /**< */
/* 8 */ TWD_OWN_EVENT_MEASUREMENT_START, /**< */
/* 9 */ TWD_OWN_EVENT_MEASUREMENT_COMPLETE, /**< */
/* 10 */ TWD_OWN_EVENT_SCAN_CMPLT, /**< */
/* 11 */ TWD_OWN_EVENT_SPS_SCAN_CMPLT, /**< */
/* 12 */ TWD_OWN_EVENT_AP_DISCOVERY_COMPLETE, /**< */
/* 13 */ TWD_OWN_EVENT_PS_REPORT, /**< */
/* 14 */ TWD_OWN_EVENT_PSPOLL_DELIVERY_FAILURE, /**< */
/* 15 */ TWD_OWN_EVENT_DISCONNECT_COMPLETE, /**< */
/* 16 */ TWD_OWN_EVENT_JOIN_CMPLT, /**< */
/* 17 */ TWD_OWN_EVENT_SWITCH_CHANNEL_CMPLT, /**< */
/* 18 */ TWD_OWN_EVENT_BSS_LOSE, /**< */
/* 19 */ TWD_OWN_EVENT_BSS_REGAIN, /**< */
/* 20 */ TWD_OWN_EVENT_MAX_TX_RETRY, /**< */
/* 21 */ RESERVED21, /**< */
/* 22 */ TWD_OWN_EVENT_SOFT_GEMINI_SENSE, /**< */
/* 23 */ TWD_OWN_EVENT_SOFT_GEMINI_PREDIC, /**< */
/* 24 */ TWD_OWN_EVENT_SOFT_GEMINI_AVALANCHE, /**< */
/* 25 */ TWD_OWN_EVENT_PLT_RX_CALIBRATION_COMPLETE, /**< */
/* 26 */ TWD_DBG_EVENT, /**< */
/* 27 */ TWD_HEALTH_CHECK_REPLY_EVENT, /**< */
/* 28 */ TWD_OWN_EVENT_PERIODIC_SCAN_COMPLETE, /**< */
/* 29 */ TWD_OWN_EVENT_PERIODIC_SCAN_REPORT, /**< */
/* 30 */ TWD_BA_SESSION_TEAR_DOWN_EVENT, /**< */
/* 31 */ TWD_OWN_EVENT_ALL, /**< */
/* 32 */ TWD_OWN_EVENT_MAX /**< */
} ETwdOwnEventId;
/** \enum ETwdEventId
* \brief TNETW Driver Event ID
*
* \par Description
* The TWD Event ID is used by user for registering a TWD Internal CB
* which will handle a TWD Event.
* Each field in this enum is an ID of TWD Event, and is combined of two IDs:
* TWD CB Owner (Module) ID and TWD Internal CB ID. Therefore, the CB is registered accordeing to
* Module (Owner) and Internal CB Id.
*
* \sa TWD_RegisterCb, ETwdCallbackOwner, ETwdIntCallbackId
*/
typedef enum
{
/* Internal Failure Event Callbacks */
TWD_EVENT_FAILURE = TWD_OWNER_SELF | TWD_INT_EVENT_FAILURE, /**< Failure Internal Event ID */
TWD_EVENT_COMMAND_COMPLETE = TWD_OWNER_SELF | TWD_INT_COMMAND_COMPLETE, /**< Command Complete Internal Event ID */
/* Tx Data Path Callbacks */
TWD_EVENT_TX_XFER_SEND_PKT_TRANSFER = TWD_OWNER_DRIVER_TX_XFER | TWD_INT_SEND_PACKET_TRANSFER, /**< TX Data Path Send Packet Event ID */
TWD_EVENT_TX_RESULT_SEND_PKT_COMPLETE = TWD_OWNER_TX_RESULT | TWD_INT_SEND_PACKET_COMPLETE, /**< TX Data Path Send Packet Complete Event ID */
TWD_EVENT_TX_HW_QUEUE_UPDATE_BUSY_MAP = TWD_OWNER_TX_HW_QUEUE | TWD_INT_UPDATE_BUSY_MAP, /**< TX Data Path Update-Busy-Map Event ID */
/* Rx Data Path Callbacks */
TWD_EVENT_RX_REQUEST_FOR_BUFFER = TWD_OWNER_RX_XFER | TWD_INT_REQUEST_FOR_BUFFER, /**< RX Data Path Request for Buffer Internal Event ID */
TWD_EVENT_RX_RECEIVE_PACKET = TWD_OWNER_RX_QUEUE | TWD_INT_RECEIVE_PACKET /**< RX Data Path Receive Packet Internal Event ID */
} ETwdEventId;
#ifdef TI_DBG
/** \enum ETwdPrintInfoType
* \brief TWD print functions codes
*
* \par Description
* Used for Debug - determines which Tx Info to print
*
* \sa TWD_PrintTxInfo
*/
typedef enum
{
/* 0 */ TWD_PRINT_TX_CTRL_BLK_TBL = 0, /**< Print TX Control Block Information */
/* 1 */ TWD_PRINT_TX_HW_QUEUE_INFO, /**< Print TX HW Queue Information */
/* 2 */ TWD_PRINT_TX_XFER_INFO, /**< Print TX XFER Information */
/* 3 */ TWD_PRINT_TX_RESULT_INFO, /**< Print TX Result Information */
/* 4 */ TWD_CLEAR_TX_RESULT_INFO /**< Clear TX Result Information */
} ETwdPrintInfoType;
#endif
/** \enum EIpVer
* \brief IP Version
*
* \par Description
*
* \sa TWD_PrintTxInfo
*/
typedef enum
{
/* 0 */ IP_VER_4 = 0, /**< */
/* 1 */ IP_VER_6 /**< */
} EIpVer;
/** \enum EKeyType
* \brief Key Type
*
* \par Description
* Security Key Type
*
* \sa TSecurityKeys
*/
typedef enum
{
/* 0 */ KEY_NULL = 0, /**< */
/* 1 */ KEY_WEP, /**< */
/* 2 */ KEY_TKIP, /**< */
/* 3 */ KEY_AES, /**< */
/* 4 */ KEY_XCC, /**< */
#ifdef GEM_SUPPORTED
/* 5 */ KEY_GEM
#endif
} EKeyType;
/** \enum ERegistryTxRate
* \brief TX Rate Type
*
* \par Description
*
* \sa
*/
/* Make it same as "rate_e" */
typedef enum
{
/* This value is reserved if this enum is used for MgmtCtrlTxRate - the auto mode is only valid for data packets */
/* 0 */ REG_RATE_AUTO_BIT = 0, /**< */
/* 1 */ REG_RATE_1M_BIT, /**< */
/* 2 */ REG_RATE_2M_BIT, /**< */
/* 3 */ REG_RATE_5_5M_CCK_BIT, /**< */
/* 4 */ REG_RATE_11M_CCK_BIT, /**< */
/* 5 */ REG_RATE_22M_PBCC_BIT, /**< */
/* 6 */ REG_RATE_6M_OFDM_BIT, /**< */
/* 7 */ REG_RATE_9M_OFDM_BIT, /**< */
/* 8 */ REG_RATE_12M_OFDM_BIT, /**< */
/* 9 */ REG_RATE_18M_OFDM_BIT, /**< */
/* 10 */ REG_RATE_24M_OFDM_BIT, /**< */
/* 11 */ REG_RATE_36M_OFDM_BIT, /**< */
/* 12 */ REG_RATE_48M_OFDM_BIT, /**< */
/* 13 */ REG_RATE_54M_OFDM_BIT, /**< */
/* 14 */ REG_RATE_MCS0_OFDM_BIT, /**< */
/* 15 */ REG_RATE_MCS1_OFDM_BIT, /**< */
/* 16 */ REG_RATE_MCS2_OFDM_BIT, /**< */
/* 17 */ REG_RATE_MCS3_OFDM_BIT, /**< */
/* 18 */ REG_RATE_MCS4_OFDM_BIT, /**< */
/* 19 */ REG_RATE_MCS5_OFDM_BIT, /**< */
/* 20 */ REG_RATE_MCS6_OFDM_BIT, /**< */
/* 21 */ REG_RATE_MCS7_OFDM_BIT /**< */
} ERegistryTxRate;
/** \enum EFailureEvent
* \brief Failure Event
*
* \par Description
* Used as a parameter for Failure Event CB -
* Inicates Failure Event ID, according which the Failure
* Event's data is driven
*
* \sa TWD_RegisterOwnCb, TFailureEventCb
*/
typedef enum
{
/* -1 */ NO_FAILURE = -1, /**< No Failure Event */
/* 0 */ NO_SCAN_COMPLETE_FAILURE = 0, /**< No Scan Complete Failure Event */
/* 1 */ MBOX_FAILURE, /**< Mail Box Failure Event */
/* 2 */ HW_AWAKE_FAILURE, /**< HW Awake Failure Event */
/* 3 */ TX_STUCK, /**< TX STUCK Failure Event */
/* 4 */ DISCONNECT_TIMEOUT, /**< Disconnect Timeout Failure Event */
/* 5 */ POWER_SAVE_FAILURE, /**< Power Save Failure Event */
/* 6 */ MEASUREMENT_FAILURE, /**< Measurement Failure Event */
/* 7 */ BUS_FAILURE, /**< Bus Failure Event */
/* 8 */ HW_WD_EXPIRE, /**< HW Watchdog Expire Event */
/* 9 */ RX_XFER_FAILURE, /**< Rx pkt xfer failure */
/* must be last!!! */
/* 10 */ MAX_FAILURE_EVENTS /**< Maximum number of Failure Events */
} EFailureEvent;
/** \enum ETemplateType
* \brief Template Type
*
* \par Description
* Used for setting/Getting a Template to/from FW
*
* \sa TWD_CmdTemplate, TWD_WriteMibTemplateFrame, TSetTemplate TWD_GetTemplate
*/
typedef enum
{
/* 0 */ NULL_DATA_TEMPLATE = 0, /**< NULL Data Template */
/* 1 */ BEACON_TEMPLATE, /**< Beacon Template */
/* 2 */ PROBE_REQUEST_TEMPLATE, /**< PROBE Request Template */
/* 3 */ PROBE_RESPONSE_TEMPLATE, /**< PROBE Response Template */
/* 4 */ QOS_NULL_DATA_TEMPLATE, /**< Quality Of Service NULL Data Template */
/* 5 */ PS_POLL_TEMPLATE, /**< Power Save Poll Template */
/* 6 */ KEEP_ALIVE_TEMPLATE, /**< Keep Alive Template */
/* 7 */ DISCONN_TEMPLATE /**< Disconn (Deauth/Disassoc) Template */
} ETemplateType;
typedef enum
{
KEY_WEP_DEFAULT = 0,
KEY_WEP_ADDR = 1,
KEY_AES_GROUP = 4,
KEY_AES_PAIRWISE = 5,
KEY_WEP_GROUP = 6,
KEY_TKIP_MIC_GROUP = 10,
KEY_TKIP_MIC_PAIRWISE = 11
} KeyType_enum;
/** \enum ECipherSuite
* \brief CHIPHER Suite
*
* \par Description
* Available cipher suites for admission control
*
* \sa
*/
typedef enum
{
/* 0 */ TWD_CIPHER_NONE = 0, /**< no cipher suite */
/* 1 */ TWD_CIPHER_WEP, /**< WEP-40 cipher suite */
/* 2 */ TWD_CIPHER_TKIP, /**< TKIP cipher suite */
/* 3 */ TWD_CIPHER_AES_WRAP, /**< AES WRAP cipher suite */
/* 4 */ TWD_CIPHER_AES_CCMP, /**< AES CCMP cipher suite */
/* 5 */ TWD_CIPHER_WEP104, /**< WEP-104 cipher suite */
/* 6 */ TWD_CIPHER_CKIP, /**< CKIP cipher suite */
#ifdef GEM_SUPPORTED
/* 7 */ TWD_CIPHER_GEM, /**< GEM cipher suite */
#endif
TWD_CIPHER_MAX,
TWD_CIPHER_UNKNOWN = 255 /**< UNKNOWN chpiher suite */
} ECipherSuite;
/** \enum E80211PsMode
* \brief 802.11 Power Save Mode
*
* \par Description
*
* \sa TWD_Scan, TWD_SetPsMode
*/
typedef enum
{
/* 0 */ POWER_SAVE_OFF = 0, /**< power save 802.11 OFF */
/* 1 */ POWER_SAVE_ON, /**< power save 802.11 ON */
/* 2 */ POWER_SAVE_KEEP_CURRENT /**< power save 802.11 don't change */
} E80211PsMode;
/** \enum E80211PsStatus
* \brief Set Power Save mode status
*
* \par Description
*
* \sa
*/
typedef enum
{
/* 1 */ POWER_SAVE_802_11_SUCCESS = 1, /**< power save mode Success */
/* 2 */ POWER_SAVE_802_11_FAIL, /**< power save mode Fail */
/* 3 */ POWER_SAVE_802_11_NOT_ALLOWED, /**< power save mode Not Allowed */
/* 4 */ POWER_SAVE_802_11_PENDING, /**< power save mode Pending */
/* 5 */ POWER_SAVE_802_11_IS_CURRENT /**< power save mode Is Current */
} E80211PsStatus;
/** \enum EElpCtrlMode
* \brief ELP Control Mode
*
* \par Description
*
* \sa
*/
typedef enum
{
/* 0 */ ELPCTRL_MODE_NORMAL = 0, /**< ALP Control mode Normal */
/* 1 */ ELPCTRL_MODE_KEEP_AWAKE /**< ALP Control mode Keep Awake */
} EElpCtrlMode;
/** \enum EPreamble
* \brief Preamble Type
*
* \par Description
*
* \sa TWD_CfgPreamble
*/
typedef enum
{
PREAMBLE_LONG = 0, /**< Preamble type Long */
PREAMBLE_SHORT = 1, /**< Preamble type Short */
PREAMBLE_UNSPECIFIED = 0xFF /**< Preamble type Not Specified */
} EPreamble;
/** \enum ENoiseHistogramCmd
* \brief Noise Histogram Type
*
* \par Description
*
* \sa TNoiseHistogram, TWD_CmdNoiseHistogram
*/
typedef enum
{
STOP_NOISE_HIST = 0, /**< Stop Noise Histogram */
START_NOISE_HIST = 1 /**< Start Noise Histogram */
} ENoiseHistogramCmd;
/** \enum ETnetWakeOn
* \brief ACX Wake Up Condition
*
* \par Description
*
* \sa TPowerMgmtConfig, TWD_CfgWakeUpCondition
*/
typedef enum
{
/* 0 */ TNET_WAKE_ON_BEACON = 0, /**< Indicate the wake on event of the HW - beacon.
* In this event the HW configure to be awake on every beacon.
*/
/* 1 */ TNET_WAKE_ON_DTIM, /**< Indicate the wake on event of the HW - DTIM. In this event
* the HW configure to be awake on every DITM (configure by the AP).
*/
/* 2 */ TNET_WAKE_ON_N_BEACON, /**< Indicate the wake on event of the HW - listen interval.
* In this event the HW configure to be awake on every
* configured number of beacons.
*/
/* 3 */ TNET_WAKE_ON_N_DTIM, /**< Indicate the wake on event of the HW - listen interval.
* In this event the HW configure to be awake on every
* configured number of beacons.
*/
/* 4 */ TNET_WAKE_ON_HOST /**< Indicate the wake on event of the HW - Host access only
*/
} ETnetWakeOn;
/** \enum ETxAntenna
* \brief TX Antenna Types
*
* \par Description
*
* \sa TGeneralInitParams, TTwdParamContents
*/
typedef enum
{
TX_ANTENNA_2 = 0, /**< */
TX_ANTENNA_1 = 1 /**< */
} ETxAntenna;
/** \enum ERxAntenna
* \brief RX Antenna Types
*
* \par Description
*
* \sa TGeneralInitParams, TTwdParamContents
*/
typedef enum
{
/* 0 */ RX_ANTENNA_1 = 0, /**< */
/* 1 */ RX_ANTENNA_2, /**< */
/* 2 */ RX_ANTENNA_FULL, /**< */
/* 3 */ RX_ANTENNA_PARTIAL /**< */
} ERxAntenna;
/** \enum EPowerPolicy
* \brief Save Power Level Policy
*
* \par Description
*
* \sa TWD_CfgSleepAuth
*/
typedef enum
{
/* 0 */ POWERAUTHO_POLICY_ELP = 0, /**< */
/* 1 */ POWERAUTHO_POLICY_PD, /**< */
/* 2 */ POWERAUTHO_POLICY_AWAKE, /**< */
/* 3 */ POWERAUTHO_POLICY_NUM /**< */
} EPowerPolicy;
/** \enum ESoftGeminiEnableModes
* \brief Soft-Gemini Enable Modes
*
* \par Description
*
* \sa
*/
typedef enum
{
/* 0 */ SG_DISABLE = 0, /**< */
/* 1 */ SG_PROTECTIVE, /**< */
/* 2 */ SG_OPPORTUNISTIC, /**< */
} ESoftGeminiEnableModes;
/** \enum ESoftGeminiEnableProfile
* \brief Soft-Gemini Profile Modes for S60 configuration
*
* \par Description
*
* \sa
*/
typedef enum
{
BtCoexProfData = 0,
BtCoexProfDataLowLatency,
BtCoexProfA2DP
}ESoftGeminiEnableProfile;
/** \enum EMibTemplateType
* \brief MIB Template type
*
* \par Description
*
* \sa
*/
typedef enum
{
/* 0 */ TEMPLATE_TYPE_BEACON = 0, /**< BEACON template */
/* 1 */ TEMPLATE_TYPE_PROBE_REQUEST, /**< PROB template */
/* 2 */ TEMPLATE_TYPE_NULL_FRAME, /**< NULL FRAM template */
/* 3 */ TEMPLATE_TYPE_PROBE_RESPONSE, /**< PROB Response template */
/* 4 */ TEMPLATE_TYPE_QOS_NULL_FRAME, /**< QOS Null Frame template */
/* 5 */ TEMPLATE_TYPE_PS_POLL /**< Power Save Poll template */
} EMibTemplateType;
/** \enum ERxFailure
* \brief RX Failure/Error
*
* \par Description
*
* \sa
*/
typedef enum
{
/* 0 */ RX_FAILURE_NONE = 0, /**< No Failure */
/* 1 */ RX_FAILURE_DECRYPT, /**< DeCrypt Failure */
/* 2 */ RX_FAILURE_MIC_ERROR, /**< MIC Error */
} ERxFailure;
/** \enum ETwdChannelWidth
* \brief TWD Channel Width
*
* \par Description
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 0 */ CHANNEL_WIDTH_20MHZ = 0, /**< 20MHZ Channel Width */
/* 1 */ CHANNEL_WIDTH_40MHZ_20MHZ /**< 40-20MHZ Channel Width */
} ETwdChannelWidth;
/** \enum ETwdRxSTBC
* \brief RX STBC Spatial Stream Supported
*
* \par Description
* Indicates how many RX STBC Spatial Stream are Supported
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 0 */ RXSTBC_NOT_SUPPORTED = 0, /**< No Spatial Stream Supported */
/* 1 */ RXSTBC_SUPPORTED_ONE_SPATIAL_STREAM, /**< One Spatial Stream Supported */
/* 2 */ RXSTBC_SUPPORTED_ONE_AND_TWO_SPATIAL_STREAMS, /**< One and Two Spatial Stream Supported */
/* 3 */ RXSTBC_SUPPORTED_ONE_TWO_AND_THREE_SPATIAL_STREAMS /**< One, Two and Three Spatial Stream Supported */
} ETwdRxSTBC;
/** \enum ETwdMaxAMSDU
* \brief Maximum MSDU Octets
*
* \par Description
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 0 */ MAX_MSDU_3839_OCTETS = 0, /**< Maximum MSDU Octets Number: 3839 */
/* 1 */ MAX_MSDU_7935_OCTETS /**< Maximum MSDU Octets Number: 7935 */
} ETwdMaxAMSDU;
/** \enum ETwdMaxAMPDU
* \brief Maximum MPDU Octets
*
* \par Description
* Indicates What is the Maximum MPDU Octets Number
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 0 */ MAX_MPDU_8191_OCTETS = 0, /**< Maximum MPDU Octets Number: 8191 */
/* 1 */ MAX_MPDU_16383_OCTETS, /**< Maximum MPDU Octets Number: 16383 */
/* 2 */ MAX_MPDU_32767_OCTETS, /**< Maximum MPDU Octets Number: 32767 */
/* 3 */ MAX_MPDU_65535_OCTETS /**< Maximum MPDU Octets Number: 65535 */
} ETwdMaxAMPDU;
/** \enum ETwdAMPDUSpacing
* \brief TWD AMPDU Spacing
*
* \par Description
* Indicates What is the Time Spacing of AMPDU
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 0 */ AMPDU_SPC_NO_RESTRCITION = 0, /**< No Restriction on AMPDU Time Spacing */
/* 1 */ AMPDU_SPC_1_4_MICROSECONDS, /**< 1/4 Microsecond AMPDU Time Spacing */
/* 2 */ AMPDU_SPC_1_2_MICROSECONDS, /**< 1/2 Microsecond AMPDU Time Spacing */
/* 3 */ AMPDU_SPC_1_MICROSECOND, /**< 1 Microsecond AMPDU Time Spacing */
/* 4 */ AMPDU_SPC_2_MICROSECONDS, /**< 2 Microsecond AMPDU Time Spacing */
/* 5 */ AMPDU_SPC_4_MICROSECONDS, /**< 4 Microsecond AMPDU Time Spacing */
/* 6 */ AMPDU_SPC_8_MICROSECONDS, /**< 8 Microsecond AMPDU Time Spacing */
/* 7 */ AMPDU_SPC_16_MICROSECONDS /**< 16 Microsecond AMPDU Time Spacing */
} ETwdAMPDUSpacing;
/** \enum ETwdMcsSupport
* \brief TWD MCS Support
*
* \par Description
* BIT Mapp which Indicates What is the Tx/rx MCS Support Enabled
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 1 */ MCS_SUPPORT_MCS_0 = BIT_0, /**< BIT 0 */
/* 2 */ MCS_SUPPORT_MCS_1 = BIT_1, /**< BIT 1 */
/* 3 */ MCS_SUPPORT_MCS_2 = BIT_2, /**< BIT 2 */
/* 4 */ MCS_SUPPORT_MCS_3 = BIT_3, /**< BIT 3 */
/* 5 */ MCS_SUPPORT_MCS_4 = BIT_4, /**< BIT 4 */
/* 6 */ MCS_SUPPORT_MCS_5 = BIT_5, /**< BIT 5 */
/* 7 */ MCS_SUPPORT_MCS_6 = BIT_6, /**< BIT 6 */
/* 8 */ MCS_SUPPORT_MCS_7 = BIT_7 /**< BIT 7 */
} ETwdMcsSupport;
/** \enum ETwdPCOTransTime
* \brief TWD PCO Transition Time
*
* \par Description
* Indicates What is the PCO Transition Time
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 0 */ PCO_TRANS_TIME_NO_TRANSITION = 0, /**< No PCO Transition Time */
/* 1 */ PCO_TRANS_TIME_400_MICROSECONDS, /**< PCO Transition Time: 400 Microsecond */
/* 2 */ PCO_TRANS_TIME_1_5_MILLISECONDS, /**< PCO Transition Time: 1.5 Millisecond */
/* 3 */ PCO_TRANS_TIME_5_MILLISECONDS /**< PCO Transition Time: 5 Millisecond */
} ETwdPCOTransTime;
/** \enum ETwdHTCapabilitiesBitMask
* \brief TWD HT Capabilities Bit Mask Mapping
*
* \par Description
* Mapps the Bit Mask which are used for Making (Enabling/Disabling)
* HT Capabilities
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 1 */ CAP_BIT_MASK_GREENFIELD_FRAME_FORMAT = BIT_0, /**< BIT 0 */
/* 2 */ CAP_BIT_MASK_SHORT_GI_FOR_20MHZ_PACKETS = BIT_1, /**< BIT 1 */
/* 3 */ CAP_BIT_MASK_SHORT_GI_FOR_40MHZ_PACKETS = BIT_2, /**< BIT 2 */
/* 4 */ CAP_BIT_MASK_SUPPORT_FOR_STBC_IN_TRANSMISSION = BIT_3, /**< BIT 3 */
/* 5 */ CAP_BIT_MASK_DELAYED_BLOCK_ACK = BIT_4, /**< BIT 4 */
/* 6 */ CAP_BIT_MASK_DSSS_CCK_IN_40_MHZ = BIT_5, /**< BIT 5 */
/* 7 */ CAP_BIT_MASK_LSIG_TXOP_PROTECTION = BIT_6, /**< BIT 6 */
/* 8 */ CAP_BIT_MASK_PCO = BIT_7, /**< BIT 7 */
/* 9 */ CAP_BIT_MASK_LDPC_CODING = BIT_8 /**< BIT 8 */
} ETwdHTCapabilitiesBitMask;
/** \enum ETwdMCSFeedback
* \brief TWD MCS FeedBack
*
* \par Description
* Indicates what is the MCS FeedBack Policy
* Used for Configure HT Capabilities Settings
*
* \sa TWD_SetDefaults, TTwdHtCapabilities
*/
typedef enum
{
/* 0 */ MCS_FEEDBACK_NO = 0, /**< */
/* 1 */ MCS_FEEDBACK_RESERVED, /**< */
/* 2 */ MCS_FEEDBACK_UNSOLICTED_ONLY, /**< */
/* 3 */ MCS_FEEDBACK_BOTH_SOLICTED_AND_UNSOLICTED /**< */
} ETwdMCSFeedback;
/** \enum ETwdTxMcsSet
* \brief TWD TX MCS Set
*
* \par Description
* Indicates Whether to set Tx MCS
*
* \sa
*/
typedef enum
{
TX_MCS_SET_NO = 0, /**< Don't Set Tx MCS */
TX_MCS_SET_YES = 1 /**< Set Tx MCS */
} ETwdTxMcsSet;
/** \enum ETwdTxRxNotEqual
* \brief TWD TX RX Not Equal
*
* \par Description
* Indicates Whether the TX and RX channels are equal
*
* \sa
*/
typedef enum
{
TX_RX_NOT_EQUAL_NO = 0, /**< TX and RX Channels are not equal */
TX_RX_NOT_EQUAL_YES = 1 /**< TX and RX Channels are equal */
} ETwdTxRxNotEqual;
/** \enum ETwdHtcSupport
* \brief TWD HTc Support
*
* \par Description
* Indicates Whether the HT Capability is Supported
*
* \sa
*/
typedef enum
{
HTC_SUPPORT_NO = 0, /**< HT Capability is not Supported */
HTC_SUPPORT_YES = 1 /**< HT Capability is Supported */
} ETwdHtcSupport;
/** \enum ESendCompleteStatus
* \brief Send complete status
*
* \par Description
* Indicates the current Success/Failure Status of Completion of Send Operation
*
* \sa
*/
typedef enum
{
/* 0 */ SEND_COMPLETE_SUCCESS = 0, /**< Send Complete Success: Completion of Send Operation is OK
*/
/* 1 */ SEND_COMPLETE_RETRY_EXCEEDED, /**< Send Complete Retry Exceeded:
* Completion of Send Operation filed because it Exceeded Allowed retries Number
*/
/* 2 */ SEND_COMPLETE_LIFETIME_EXCEEDED, /**< Send Complete Lifetiem Exceeded:
* Completion of Send Operation failed because it Exceeded Allowed Lifetime
*/
/* 3 */ SEND_COMPLETE_NO_LINK, /**< Send Complete No Link:
* Completion of Send Operation failed because No Link was found
*/
/* 4 */ SEND_COMPLETE_MAC_CRASHED /**< Send Complete MAC Crashed:
* Completion of Send Operation failed because MAC Crashed
*/
} ESendCompleteStatus;
/** \enum EPacketType
* \brief Packet type
*
* \par Description
*
* \sa
*/
typedef enum
{
/* 0 */ PACKET_DATA = 0, /**< */
/* 1 */ PACKET_CTRL, /**< */
/* 2 */ PACKET_MGMT /**< */
} EPacketType;
/** \enum ETxHwQueStatus
* \brief Status returned by txHwQueue_AllocResources
*
* \par Description
*
* \sa
*/
typedef enum
{
TX_HW_QUE_STATUS_SUCCESS, /* Resources available on current queue */
TX_HW_QUE_STATUS_STOP_CURRENT, /* No resources, stop current queue and requeue the packet */
TX_HW_QUE_STATUS_STOP_NEXT /* Resources available for this packet but not for another one,
so just stop the current queue */
} ETxHwQueStatus;
/** \enum ERxBufferStatus
* \brief Status returned by TRequestForBufferCb
*
* \par Description
*
* \sa
*/
typedef enum
{
RX_BUF_ALLOC_PENDING,
RX_BUF_ALLOC_COMPLETE,
RX_BUF_ALLOC_OUT_OF_MEM
}ERxBufferStatus;
/*
* --------------------------------------------------------------
* Structures
* --------------------------------------------------------------
*/
/**
* \brief Get File Callback
*
* \param hCbHndl - Handle to CB Object
* \return void
*
* \par Description
* The callback function type for GetFile users
*
* \sa TFileInfo
*/
typedef void (*TGetFileCbFunc)(TI_HANDLE hCbHndl);
/** \struct TFileInfo
* \brief File Information
*
* \par Description
* Contains all needed information and structures for Getting file
*
* \sa TWD_InitFw
*/
typedef struct
{
EFileType eFileType; /**< Requested file type */
TI_UINT8 *pBuffer; /**< Pointer to Buffer into the file (or file portion) is copied from user space */
TI_UINT32 uLength; /**< Length of data currently held in pBuffer */
TI_UINT32 uOffset; /**< Offset in File of data currently held in pBuffer */
TI_UINT32 uAddress; /**< Offset in File of data currently held in pBuffer */
TI_BOOL bLast; /**< TRUE indicates that we reached end of file */
void *hOsFileDesc; /**< OAL file-descriptor handle for repeated access to same file (FW) */
TGetFileCbFunc fCbFunc; /**< CB function to call if file read is finished in a later context (future option) */
TI_HANDLE hCbHndl; /**< Handle to provide when calling fCbFunc */
TI_UINT32 uChunksLeft; /**< Chunks Left to read from File (used if file is read in chunks) */
TI_UINT32 uChunkBytesLeft; /**< Number of bytes of Last read chunk, which were not yet handled */
TI_UINT32 uCrcCalc; /**< Current Calculated CRC */
} TFileInfo;
/** \struct T80211Header
* \brief 802.11 MAC header
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT16 fc; /**< */
TI_UINT16 dur; /**< */
TMacAddr address1; /**< */
TMacAddr address2; /**< */
TMacAddr address3; /**< */
TI_UINT16 seq; /**< */
TI_UINT16 qos; /**< */
} T80211Header;
/** \struct TKeepAliveParams
* \brief Keep Alive Parameters
*
* \par Description
*
* \sa TWD_CfgKeepAlive
*/
typedef struct
{
TI_UINT8 index; /**< */
TI_UINT8 enaDisFlag; /**< */
TI_UINT32 interval; /**< */
EKeepAliveTriggerType trigType; /**< */
} TKeepAliveParams;
/** \struct TPsRxStreaming
* \brief Power Save RX Streaming
*
* \par Description
* The configuration of Rx streaming delivery in PS mode per TID
*
* \sa TWD_CfgKeepAlive
*/
typedef struct
{
TI_UINT32 uTid; /**< The configured TID (0-7) */
TI_UINT32 uStreamPeriod; /**< The expected period between two packets of the delivered stream */
TI_UINT32 uTxTimeout; /**< Start sending triggers if no Tx traffic triggers arrive for this priod */
TI_BOOL bEnabled; /**< If TRUE enable this TID streaming, if FALSE disable it. */
} TPsRxStreaming;
/** \struct TDmaParams
* \brief DMA Parameters
*
* \par Description
* Struct which holds DMA Rx/Tx Queues and Bufffers params
*
* \sa
*/
typedef struct
{
TI_UINT32 NumRxBlocks; /**< Allocated RX memory blocks number */
TI_UINT32 NumTxBlocks; /**< Allocated TX memory blocks number */
TI_UINT8 NumStations; /**< Number of Stations */
void *fwTxResultInterface; /**< RX minimum Memory block number */
TI_UINT8 *fwRxCBufPtr; /**< Pointer to FW RX Control Buffer */
TI_UINT8 *fwTxCBufPtr; /**< Pointer to FW TX Control Buffer */
void *fwRxControlPtr; /**< Pointer to FW TX Control */
void *fwTxControlPtr; /**< Pointer to FW RX Control */
TI_UINT32 PacketMemoryPoolStart; /**< RX Memory block offset */
} TDmaParams;
/** \struct TSecurityKeys
* \brief Security Key
*
* \par Description
* Struct which holds Security Key Parameters
* Used for handling DMA
*
* \sa
*/
typedef struct
{
EKeyType keyType; /**< Security Key Type (WEP, TKIP etc.) */
TI_UINT32 encLen; /**< Security Key length in bytes */
TI_UINT8 encKey[MAX_KEY_LEN]; /**< Security Key Encoding */
TI_UINT8 micRxKey[MAX_KEY_LEN]; /**< MIC RX Security Key */
TI_UINT8 micTxKey[MAX_KEY_LEN]; /**< MIC TX Security Key */
TI_UINT32 keyIndex; /**< Security Key Index (id=0 is broadcast key) */
TMacAddr macAddress; /**< Security Key MAC Address */
TI_UINT8 keyRsc[KEY_RSC_LEN]; /**< Security Key RSC */
} TSecurityKeys;
/** \struct TxPktParams_t
* \brief TX Packet Parameters
*
* \par Description
* Tx Control-Block Packet parameters that are not included in the Tx-descriptor
*
* \sa
*/
typedef struct
{
void * pInputPkt; /**< The input packet to the Tx path, either OS packet or raw buffer (see RAW_BUF_PKT flag) */
TI_UINT32 uInputPktLen; /**< The input packet length in bytes (for freeing it in case of raw buffer) */
TI_UINT32 uDriverDelay; /**< The time in uSec the pkt was delayed in the driver until Xfer */
TI_UINT8 uPktType; /**< See TX_PKT_TYPE_xxxx above */
TI_UINT8 uHeadroomSize; /**< Only for WHA - headroom in bytes before the payload in the packet buffer */
TI_UINT16 uFlags; /**< See TX_CTRL_FLAG__xxxx above */
} TTxPktParams;
/** \struct TTxCtrlBlk
* \brief TX Control Block Entry
*
* \par Description
* Contains the Tx packet parameters required for the Tx process, including
* the Tx descriptor and the attributes required for HW-queue calculations.
* TX Control Block Entry is allocated for each packet sent from the upper
* driver and freed upon Tx-complete.
* The entry index is the descriptor-ID. It is written in the descriptor and
* copied back into the tx-complete results
*
* \sa SendPacketTranferCB_t, SendPacketDebugCB_t, TWD_txCtrlBlk_alloc, TWD_txCtrlBlk_free, TWD_txCtrlBlk_GetPointer, TWD_txXfer_sendPacket
*/
typedef struct _TTxCtrlBlk
{
TTxnStruct tTxnStruct; /**< The transaction structure for packet queueing and transaction via the bus driver */
TxIfDescriptor_t tTxDescriptor; /**< The packet descriptor copied to the FW */
TI_UINT8 aPktHdr[MAX_HEADER_SIZE]; /**< The packet header + extensions (see description of MAX_HEADER_SIZE above) */
TTxPktParams tTxPktParams; /**< Per packet parameters not included in the descriptor */
struct _TTxCtrlBlk *pNextFreeEntry; /**< Pointer to the next free entry */
} TTxCtrlBlk;
/** \struct TTemplateParams
* \brief Template Parameters
*
* \par Description
*
* \sa TWD_GetTemplate
*/
typedef struct
{
TI_UINT32 Size; /**< Template size */
TI_UINT32 uRateMask; /**< The rates bitmap for the frame */
TI_UINT8 Buffer[MAX_TEMPLATE_SIZE]; /**< Buffer which holds Template */
} TTemplateParams;
/** \struct TFwInfo
* \brief FW Information
*
* \par Description
*
* \sa TWD_GetFWInfo
*/
typedef struct
{
TI_UINT8 fwVer[FW_VERSION_LEN]; /**< Firmware version - null terminated string */
TMacAddr macAddress; /**< MAC Address */
TI_UINT8 txPowerTable[NUMBER_OF_SUB_BANDS_E][NUM_OF_POWER_LEVEL]; /**< Maximun Dbm in Dbm/10 units */
TI_UINT32 uHardWareVersion; /**< HW Version */
} TFwInfo;
/** \struct TJoinBss
* \brief Join BSS Parameters
*
* \par Description
*
* \sa TWD_CmdJoinBss
*/
typedef struct
{
ScanBssType_e bssType; /**< */
TI_UINT16 beaconInterval; /**< */
TI_UINT16 dtimInterval; /**< */
TI_UINT8 channel; /**< */
TI_UINT8* pBSSID; /**< */
TI_UINT8* pSSID; /**< */
TI_UINT8 ssidLength; /**< */
TI_UINT32 basicRateSet; /**< */
ERadioBand radioBand; /**< */
/* Current Tx-Session index as configured to FW in last Join command */
TI_UINT16 txSessionCount; /**< */
} TJoinBss;
/** \struct TSetTemplate
* \brief Set Template Parameters
*
* \par Description
*
* \sa TWD_CmdTemplate, TWD_WriteMibTemplateFrame
*/
typedef struct
{
ETemplateType type; /**< Template Type */
TI_UINT8 index; /**< only valid for keep-alive templates */
TI_UINT8* ptr; /**< Pointer to Template Data */
TI_UINT32 len; /**< Pointer to Template Length */
ERadioBand eBand; /**< only valid for probe request templates */
TI_UINT32 uRateMask;/**< The rate mask to use for this frame */
} TSetTemplate;
/** \struct TNoiseHistogram
* \brief Noise Histogram Parameters
*
* \par Description
*
* \sa TWD_CmdNoiseHistogram
*/
typedef struct
{
ENoiseHistogramCmd cmd; /**< Noise Histogram Command (Start/Atop) */
TI_UINT16 sampleInterval; /**< Sample Interval (in microsec) */
TI_UINT8 ranges [MEASUREMENT_NOISE_HISTOGRAM_NUM_OF_RANGES]; /**< Noise Histogram Ranges */
} TNoiseHistogram;
/** \struct TInterogateCmdHdr
* \brief Interrogate Command Header
*
* \par Description
*
* \sa TNoiseHistogramResults, TMediumOccupancy, TTsfDtim
*/
typedef struct
{
TI_UINT16 id; /**< */
TI_UINT16 len; /**< */
} TInterogateCmdHdr;
/** \struct TNoiseHistogramResults
* \brief Noise Histogram Results
*
* \par Description
* Used for Getting Noise Histogram Parameters from FW
*
* \sa
*/
typedef struct
{
TInterogateCmdHdr noiseHistResCmdHdr; /**< Results Header */
TI_UINT32 counters[NUM_OF_NOISE_HISTOGRAM_COUNTERS]; /**< Counters */
TI_UINT32 numOfLostCycles; /**< Number of Lost Cycles */
TI_UINT32 numOfTxHwGenLostCycles; /**< Number of Tx Hw Gen Lost Cycles */
TI_UINT32 numOfRxLostCycles; /**< Number of RX Hw Gen Lost Cycles */
} TNoiseHistogramResults;
/** \struct TMediumOccupancy
* \brief Medium Occupancy Parameters
*
* \par Description
* Used for Getting Medium Occupancy (Channal Load) from FW
* or print Medium Occupancy (Channal Load) Debug Information
*
* \sa
*/
typedef struct
{
TInterogateCmdHdr mediumOccupCmdHdr; /**< Command Header */
TI_UINT32 MediumUsage; /**< Medium Occupancy Usage Time */
TI_UINT32 Period; /**< Medium Occupancy Period Time */
} TMediumOccupancy;
/** \struct TTsfDtim
* \brief Beacon TSF and DTIM count
*
* \par Description
* Used for Getting updated current TSF and last Beacon TSF and DTIM Count from FW
* for Scan Purposes
*
* \sa
*/
typedef struct
{
TInterogateCmdHdr tsf_dtim_mibCmdHdr; /**< Command Header */
TI_UINT32 CurrentTSFHigh; /**< Current TSF High (of INT64) Value */
TI_UINT32 CurrentTSFLow; /**< Current TSF Low (of INT64) Value */
TI_UINT32 lastTBTTHigh; /**< Last TBTT High (of INT64) Value */
TI_UINT32 lastTBTTLow; /**< Last TBTT Low (of INT64) Value */
TI_UINT8 LastDTIMCount; /**< Last DTIM Count */
TI_UINT8 Reserved[3]; /**< Reserved */
} TTsfDtim;
/** \struct TBcnBrcOptions
* \brief Beacon broadcast options
*
* \par Description
* Used for Getting/Configuring updated Beacon broadcast options from/to FW
*
* \sa TWD_SetDefaults
*/
typedef struct
{
TI_UINT16 BeaconRxTimeout; /**< Beacon RX Timeout */
TI_UINT16 BroadcastRxTimeout; /**< Broadcast RX Timeout */
TI_UINT8 RxBroadcastInPs; /**< RX Broadcast In Power Save */
} TBcnBrcOptions;
/** \struct TBeaconFilterIeTable
* \brief Beacon Filter Information Elements Table
*
* \par Description
* Used for Getting/Configuring Beacon Filter IE Table From/To FW
*
* \sa TWD_SetDefaults
*/
typedef struct
{
TI_UINT8 numberOfIEs; /**< Number of IE Tables */
TI_UINT8 IETable[BEACON_FILTER_TABLE_MAX_SIZE]; /**< The IE table */
TI_UINT8 IETableSize; /**< number of elements in IE table */
} TBeaconFilterIeTable;
/** \struct TBeaconFilterInitParams
* \brief Beacon Filter Init Parameters
*
* \par Description
* Used for Init Beacon Filter IE Table in FW
*
* \sa
*/
typedef struct
{
TI_UINT8 desiredState; /**< Desigred state (required/not required) */
TI_UINT8 numOfStored; /**< Number of desigred Beacon Filters stored in FW */
TI_UINT8 numOfElements; /**< Number of Beacon Filter Elements stored in FW */
TI_UINT8 IETableSize; /**< The IE Table size */
TI_UINT8 reserve[3]; /**< Reserved */
TI_UINT8 IETable[BEACON_FILTER_IE_TABLE_MAX_SIZE]; /**< The IE table */
} TBeaconFilterInitParams;
/** \struct TPowerMgmtConfig
* \brief Power Management Configuration Parameters
*
* \par Description
* Used for Configuring Wake-Up Conditions or Beacon Broadcast Options to FW
*
* \sa TWD_CfgWakeUpCondition, TWD_CfgBcnBrcOptions
*/
typedef struct
{
/* power management options */
TI_UINT8 beaconListenInterval; /**< Beacon Listen Interavl:
* specify how often the TNET wakes up to listen to beacon frames.
* the value is expressed in units of "beacon interval"
*/
TI_UINT8 beaconFiltering; /**< Beacon Filtering Desigred state (required/not required) */
TI_UINT8 DTIMListenInterval; /**< DTIM Listen Interavl:
* specify how often the TNET wakes up to listen to DTIM frames. the value
* is expressed in units of "dtim interval"
*/
TI_UINT8 NConsecutiveBeaconMiss; /**< Consecutive Beacon Miss */
TI_UINT8 hangoverPeriod; /**< Hang Over Period */
TI_UINT8 HwPsPollResponseTimeout; /**< Power-Save Polling Response Time Out */
TI_UINT32 BaseBandWakeUpTime; /**< Base Band Wakeup Time */
TI_UINT32 beaconReceiveTime; /**< Beacon Receive Time */
TI_BOOL beaconMissInterruptEnable; /**< Enable/Disable Beacon Miss Interrupt */
TI_BOOL rxBroadcast; /**< Enable/Disable receive of broadcast packets in Power-Save mode */
TI_BOOL hwPsPoll; /**< Enable/Disable Power-Save Polling */
/* Power Management Configuration IE */
TI_BOOL ps802_11Enable; /**< Enable/Disable 802.11 Power-Save */
TI_UINT8 needToSendNullData; /**< Indicates if need to send NULL data */
TI_UINT8 numNullPktRetries; /**< Number of NULL Packets allowed retries */
TI_UINT8 hangOverPeriod; /**< HangOver period:
* Indicates what is the time in TUs during which the WiLink remains awake
* after sending an MPDU with the Power Save bit set (indicating that the
* station is to go into Power Save mode). Setting bit 0 does not affect
* the hangover period
*/
TI_UINT16 NullPktRateModulation; /**< Null Packet Rate Modulation */
/* PMConfigStruct */
TI_BOOL ELPEnable; /**< Enable/Disable ELP */
TI_UINT32 BBWakeUpTime; /**< Base Band Wakeup Time */
TI_UINT32 PLLlockTime; /**< PLL Lock Time */
/* AcxBcnBrcOptions */
TBcnBrcOptions BcnBrcOptions; /**< Beacon broadcast options */
/* ACXWakeUpCondition */
ETnetWakeOn tnetWakeupOn; /**< ACX Wake Up Condition */
TI_UINT8 listenInterval; /**< ACX Listen Interval */
/* No answer after Ps-Poll work-around */
TI_UINT8 ConsecutivePsPollDeliveryFailureThreshold; /**< Power-Save Polling Delivery Failure Threshold */
} TPowerMgmtConfig;
/** \struct TPowerSaveParams
* \brief Power Save Parameters
*
* \par Description
*
* \sa
*/
typedef struct
{
/* powerMgmtConfig IE */
TI_BOOL ps802_11Enable; /**< Enable/Disable 802.11 Power-Save */
TI_UINT8 needToSendNullData; /**< Indicates if need to send NULL data */
TI_UINT8 numNullPktRetries; /**< Number of NULL Packets allowed retries */
TI_UINT8 hangOverPeriod; /**< HangOver period:
* Indicates what is the time in TUs during which the WiLink remains awake
* after sending an MPDU with the Power Save bit set (indicating that the
* station is to go into Power Save mode). Setting bit 0 does not affect
* the hangover period
*/
EHwRateBitFiled NullPktRateModulation; /**< Null Packet Rate Modulation */
} TPowerSaveParams;
/** \struct TAcQosParams
* \brief AC QoS Parameters
*
* \par Description
* Used for Configuring AC Parameters (For Quality Of Service) to FW
*
* \sa TWD_CfgAcParams
*/
typedef struct
{
TI_UINT8 ac; /**< Access Category - The TX queue's access category */
TI_UINT8 cwMin; /**< The contention window minimum size (in slots) */
TI_UINT16 cwMax; /**< The contention window maximum size (in slots) */
TI_UINT8 aifsn; /**< The AIF value (in slots) */
TI_UINT16 txopLimit; /**< The TX Op Limit (in microseconds) */
} TAcQosParams;
/** \struct TMeasurementParams
* \brief AC Queues Parameters
*
* \par Description
* Used When Send Start Measurment Command to FW
*
* \sa TWD_CmdMeasurement
*/
typedef struct
{
TI_UINT32 ConfigOptions; /**< RX Filter Configuration Options */
TI_UINT32 FilterOptions; /**< RX Filter Options */
TI_UINT32 duration; /**< Specifies the measurement process duration in microseconds. The value of 0 means
* infinite duration in which only a STOP_MEASUREMENT command can stop the measurement
* process
*/
Channel_e channel; /**< Channel number on which the measurement is performed */
RadioBand_e band; /**< Specifies the band to which the channel belongs */
EScanResultTag eTag; /**< Scan Result Tag */
} TMeasurementParams;
/** \struct TApDiscoveryParams
* \brief AP Discovery Parameters
*
* \par Description
* Used When Performing AP Discovery
*
* \sa TWD_CmdApDiscovery
*/
typedef struct
{
TI_UINT32 ConfigOptions; /**< RX Configuration Options for measurement */
TI_UINT32 FilterOptions; /**< RX Filter Configuration Options for measurement */
TI_UINT32 scanDuration; /**< This field specifies the amount of time, in time units (TUs), to perform the AP discovery */
TI_UINT16 scanOptions; /**< This field specifies whether the AP discovery is performed by an active scan or a passive scan
* 0 - ACTIVE, 1 - PASSIVE
*/
TI_UINT8 numOfProbRqst; /**< This field indicates the number of probe requests to send per channel, when active scan is specified
* Note: for XCC measurement this value should be set to 1
*/
TI_UINT8 txPowerDbm; /**< TX power level to be used for sending probe requests when active scan is specified.
* If 0, leave normal TX power level for this channel
*/
EHwRateBitFiled txdRateSet; /**< This EHwBitRate format field specifies the rate and modulation to transmit the probe request when
* an active scan is specifie
*/
ERadioBand eBand; /**< Specifies the band to which the channel belongs */
} TApDiscoveryParams;
/** \struct TRroamingTriggerParams
* \brief Roaming Trigger Parameters
*
* \par Description
*
* \sa TWD_CfgMaxTxRetry, TWD_CfgConnMonitParams
*/
typedef struct
{
/* ACXConsNackTriggerParameters */
TI_UINT8 maxTxRetry; /**< The number of frames transmission failures before issuing the "Max Tx Retry" event */
/* ACXBssLossTsfSynchronize */
TI_UINT16 TsfMissThreshold; /**< The number of consecutive beacons that can be lost before the WiLink raises the
* SYNCHRONIZATION_TIMEOUT event
*/
TI_UINT16 BssLossTimeout; /**< The delay (in time units) between the time at which the device issues the SYNCHRONIZATION_TIMEOUT
* event until, if no probe response or beacon is received a BSS_LOSS event is issued
*/
} TRroamingTriggerParams;
/** \struct TSwitchChannelParams
* \brief Switch Channel Parameters
*
* \par Description
* Used for Switch channel Command
*
* \sa TWD_CmdSwitchChannel
*/
typedef struct
{
TI_UINT8 channelNumber; /**< The new serving channel */
TI_UINT8 switchTime; /**< Relative time of the serving channel switch in TBTT units */
TI_UINT8 txFlag; /**< 1: Suspend TX till switch time; 0: Do not suspend TX */
TI_UINT8 flush; /**< 1: Flush TX at switch time; 0: Do not flush */
} TSwitchChannelParams;
/** \struct TRxCounters
* \brief RX Counters
*
* \par Description
* Used for Getting RX Counters from FW
*
* \sa
*/
typedef struct
{
TI_UINT32 RecvError; /**< Number of frames that a NIC receives but does not indicate to the protocols due to errors */
TI_UINT32 RecvNoBuffer; /**< Number of frames that the NIC cannot receive due to lack of NIC receive buffer space */
TI_UINT32 FragmentsRecv; /**< Number of Fragments Received */
TI_UINT32 FrameDuplicates; /**< Number of Farme Duplicates */
TI_UINT32 FcsErrors; /**< Number of frames that a NIC receives but does not indicate to the protocols due to errors */
} TRxCounters;
/** \struct TApPowerConstraint
* \brief AP Power Constraint
*
* \par Description
*
* \sa
*/
typedef struct
{
INFO_ELE_HDR /**< Information Element Header */
int8 powerConstraintOnBss; /**< The attenuation from the regulatory power constraint as declared by the AP
* Units: dBm ; Range: -20 - 30
*/
} TApPowerConstraint;
/*
* TConfigCmdCbParams, TInterrogateCmdCbParams:
* Note that this structure is used by the GWSI
* both for setting (writing to the device) and
* for retreiving (Reading from the device),
* while being called with a completion CB
*/
/** \struct TConfigCmdCbParams
* \brief Config Command CB Parameters
*
* \par Description
* The CB Parameters (Completino CB, Handle to CB Parameters and buffer of Input/Output Parameters)
* are used for Setting Parameters
*
* \sa TWD_SetParam
*/
typedef struct
{
void* fCb; /**< Completion CB function */
TI_HANDLE hCb; /**< CB handle */
void* pCb; /**< CBuffer contains the content to be written or the retrieved content */
} TConfigCmdCbParams;
/** \struct TInterrogateCmdCbParams
* \brief Interrogate Command Parameters
*
* \par Description
* Interrogate Command Parameters are the same as configuration Command CB Parameters
*
* \sa TWD_SetParam
*/
typedef TConfigCmdCbParams TInterrogateCmdCbParams;
/** \struct TRxTimeOut
* \brief RX Time Out
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT16 psPoll; /**< The maximum time that the device will wait to receive traffic from the AP after transmission of PS-poll */
TI_UINT16 UPSD; /**< The maximum time that the device will wait to receive traffic from the AP after transmission from UPSD
* enabled queue
*/
} TRxTimeOut;
/** \struct TQueueTrafficParams
* \brief RX Time Out
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT8 queueID; /**< The TX queue ID number (0-7) */
TI_UINT8 channelType; /**< Channel access type for the queue Refer to ChannelType_enum */
TI_UINT8 tsid; /**< for EDCA - the AC Index (0-3, refer to AccessCategory_enum).
* For HCCA - HCCA Traffic Stream ID (TSID) of the queue (8-15)
*/
TI_UINT32 dot11EDCATableMSDULifeTime; /**< 802.11 EDCA Table MSDU Life Time */
TI_UINT8 psScheme; /**< The power save scheme of the specified queue. Refer to PSScheme_enum */
TI_UINT8 ackPolicy; /**< ACK policy per AC */
TI_UINT32 APSDConf[2]; /**< APSD Configuration */
} TQueueTrafficParams;
/** \struct TFmCoexParams
* \brief FM Coexistence Parameters
*
* \par Description
* Used for Setting/Printing FM Coexistence Parameters
*
* \sa
*/
typedef struct
{
TI_UINT8 uEnable; /* enable(1) / disable(0) the FM Coex feature */
TI_UINT8 uSwallowPeriod; /* Swallow period used in COEX PLL swallowing mechanism,
Range: 0-0xFF, 0xFF = use FW default
*/
TI_UINT8 uNDividerFrefSet1; /* The N divider used in COEX PLL swallowing mechanism for Fref of 38.4/19.2 Mhz.
Range: 0-0xFF, 0xFF = use FW default
*/
TI_UINT8 uNDividerFrefSet2; /* The N divider used in COEX PLL swallowing mechanism for Fref of 26/52 Mhz.
Range: 0-0xFF, 0xFF = use FW default
*/
TI_UINT16 uMDividerFrefSet1; /* The M divider used in COEX PLL swallowing mechanism for Fref of 38.4/19.2 Mhz.
Range: 0-0x1FF, 0xFFFF = use FW default
*/
TI_UINT16 uMDividerFrefSet2; /* The M divider used in COEX PLL swallowing mechanism for Fref of 26/52 Mhz.
Range: 0-0x1FF, 0xFFFF = use FW default
*/
TI_UINT32 uCoexPllStabilizationTime;/* The time duration in uSec required for COEX PLL to stabilize.
0xFFFFFFFF = use FW default
*/
TI_UINT16 uLdoStabilizationTime; /* The time duration in uSec required for LDO to stabilize.
0xFFFFFFFF = use FW default
*/
TI_UINT8 uFmDisturbedBandMargin; /* The disturbed frequency band margin around the disturbed
frequency center (single sided).
For example, if 2 is configured, the following channels
will be considered disturbed channel:
80 +- 0.1 MHz, 91 +- 0.1 MHz, 98 +- 0.1 MHz, 102 +- 0.1 MHz
0xFF = use FW default
*/
TI_UINT8 uSwallowClkDif; /* The swallow clock difference of the swallowing mechanism.
0xFF = use FW default
*/
} TFmCoexParams;
/** \struct TMibBeaconFilterIeTable
* \brief MIB Beacon Filter IE table
*
* \par Description
* Used for Read/Write the MIB/IE Beacon Filter
* NOTE: This struct is only meant to be used as a pointer reference to an actual buffer.
* Table size is not a constant and is derived from the buffer size given with the
* user command
*
* \sa TWD_WriteMibBeaconFilterIETable
*/
typedef struct
{
/* Number of information elements in table */
TI_UINT8 iNumberOfIEs; /**< Input Number of IE Tables */
TI_UINT8 iIETable[MIB_MAX_SIZE_OF_IE_TABLE]; /**< Input IE Table */
} TMibBeaconFilterIeTable;
/** \struct TMibCounterTable
* \brief MIB Counter Table
*
* \par Description
* Used for Getting Counters of MIB Table
*
* \sa
*/
typedef struct
{
TI_UINT32 PLCPErrorCount; /**< The number of PLCP errors since the last time this information element was interrogated.
* This field is automatically cleared when it is interrogated
*/
TI_UINT32 FCSErrorCount; /**< The number of FCS errors since the last time this information element was interrogated.
* This field is automatically cleared when it is interrogated
*/
TI_UINT32 SeqNumMissCount; /**< The number of missed sequence numbers in the squentially values of frames seq numbers */
} TMibCounterTable;
/** \struct TMibWlanWakeUpInterval
* \brief MIB WLAN Wake-Up Interval
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT32 WakeUpInterval; /**< Wake Up Interval */
TI_UINT8 ListenInterval; /**< Listen interval in unit of the beacon/DTIM */
} TMibWlanWakeUpInterval;
/** \struct TMibTemplateFrame
* \brief MIB Template Frame
*
* \par Description
* Used for Writing MIB Frame Template to FW
*
* \sa TWD_WriteMibTemplateFrame
*/
typedef struct
{
EMibTemplateType FrameType; /**< MIB Farme Template type */
TI_UINT32 Rate; /**< Frame Rate */
TI_UINT16 Length; /**< Frame Length */
TI_UINT8 Data [MIB_TEMPLATE_DATA_MAX_LEN]; /**< Frame Template Data */
} TMibTemplateFrame;
/** \struct TMibArpIpAddressesTable
* \brief MIB ARP Address Table
*
* \par Description
* Used for Writing MIB ARP Table Template to FW
*
* \sa TWD_WriteMib
*/
typedef struct
{
TI_UINT32 FilteringEnable; /**< Enable/Disable Filtering */
TIpAddr addr; /**< IP Address Table */
} TMibArpIpAddressesTable;
/** \struct TMibGroupAdressTable
* \brief MIB Group Address Table
*
* \par Description
* Used for Writing MIB Group Table Template to FW
*
* \sa TWD_WriteMib
*/
typedef struct
{
TMacAddr aGroupTable[MIB_MAX_MULTICAST_GROUP_ADDRS]; /**< Table of Multicast Group Addresses */
TI_UINT8 bFilteringEnable; /**< Enable/Disable Filtering */
TI_UINT8 nNumberOfAddresses; /**< Number of Multicast Addresses */
} TMibGroupAdressTable;
/** \struct TTxRateClass
* \brief TX Rate Class
*
* \par Description
* Used for Set/Get TX Rate Policy Class to/from FW
*
* \sa
*/
typedef struct
{
TI_UINT32 txEnabledRates; /**< A Bit Mask which indicates which Rates are enabled */
TI_UINT8 shortRetryLimit; /**< */
TI_UINT8 longRetryLimit; /**< */
TI_UINT8 flags; /**< */
TI_UINT8 reserved; /**< for alignment with the FW API */
} TTxRateClass;
/** \struct TTxRatePolicy
* \brief TX Rate Policy
*
* \par Description
* Used for Set/Get TX Rate Policy to/from FW
*
* \sa
*/
typedef struct
{
TI_UINT32 numOfRateClasses; /**< */
TTxRateClass rateClass[MAX_NUM_OF_TX_RATE_CLASS_POLICIES]; /**< */
} TTxRatePolicy;
/** \struct TCoexActivity
* \brief CoexActivity Parameters
*
* \par Description
*
* \sa
*/
typedef struct {
uint8 coexIp; /* 0-BT, 1-WLAN (according to CoexIp_e in FW) */
uint8 activityId; /* According to BT/WLAN activity numbering in FW */
uint8 defaultPriority; /* 0-255, activity default priority */
uint8 raisedPriority; /* 0-255, activity raised priority */
uint16 minService; /* 0-65535, The minimum service requested either in
requests or in milliseconds depending on activity ID */
uint16 maxService; /* 0-65535, The maximum service allowed either in
requests or in milliseconds depending on activity ID */
} TCoexActivity;
/** \struct THalCoexActivityTable
* \brief CoexActivity Table Initialization Parameters
*
* \par Description
*
* \sa
*/
typedef struct
{
uint32 numOfElements;
TCoexActivity entry[COEX_ACTIVITY_TABLE_MAX_NUM];
} THalCoexActivityTable;
/** \union TMibData
* \brief MIB Data
*
* \par Description
* Union which defines all MIB Data types
* Used for write MIB Configuration to FW
*
* \sa TWD_WriteMib
*/
typedef union
{
TMacAddr StationId; /**< Station ID MAC Address */
TI_UINT32 MaxReceiveLifeTime; /**< HAl Control Max Rx MSDU Life Time, in TUs Units */
TI_UINT32 SlotTime; /**< Radio (PHY) Slot Time Type */
TMibGroupAdressTable GroupAddressTable; /**< MIB Group Address Table */
TI_UINT8 WepDefaultKeyId; /**< WEP Defualt Security Key ID */
TI_UINT8 PowerLevel; /**< */
TI_UINT16 RTSThreshold; /**< */
TI_UINT32 CTSToSelfEnable; /**< Enable/Disable CTS to Self */
TMibArpIpAddressesTable ArpIpAddressesTable; /**< MIB ARP Address Table */
TMibTemplateFrame TemplateFrame; /**< MIB Template Frame */
TI_UINT8 RxFilter; /**< */
TMibWlanWakeUpInterval WlanWakeUpInterval; /**< MIB WLAN Wake-Up Interval */
TMibCounterTable CounterTable; /**< MIB Counter Table */
TMibBeaconFilterIeTable BeaconFilter; /**< MIB Beacon Filter IE table */
TTxRatePolicy txRatePolicy; /**< TX Rate Policy */
} TMibData;
/** \struct TMib
* \brief MIB Structure
*
* \par Description
* Used for writing MIB Configuration to FW
*
* \sa TWD_WriteMib, TWD_WriteMibTemplateFrame, TWD_WriteMibBeaconFilterIETable, TWD_WriteMibTxRatePolicy
*/
typedef struct
{
EMib aMib; /**< MIB Element Type */
TI_UINT16 Length; /**< MIB Data Length */
TMibData aData; /**< MIB Data */
} TMib;
/** \union TTwdParamContents
* \brief TWD Parameters Content
*
* \par Description
* All FW Parameters contents
*
* \sa TWD_SetParam
*/
typedef union
{
TI_UINT16 halCtrlRtsThreshold; /**< */
TI_UINT8 halCtrlCtsToSelf; /**< */
TRxTimeOut halCtrlRxTimeOut; /**< */
TI_UINT16 halCtrlFragThreshold; /**< */
TI_UINT16 halCtrlListenInterval; /**< */
TI_UINT16 halCtrlCurrentBeaconInterval; /**< */
TI_UINT8 halCtrlTxPowerDbm; /**< */
ETxAntenna halCtrlTxAntenna; /**< */
ERxAntenna halCtrlRxAntenna; /**< */
TI_UINT8 halCtrlAifs; /**< */
TI_BOOL halCtrlTxMemPoolQosAlgo; /**< */
TI_BOOL halCtrlClkRunEnable; /**< */
TRxCounters halCtrlCounters; /**< */
TMib* pMib; /**< */
TI_UINT8 halCtrlCurrentChannel; /**< */
/* AC Qos parameters */
TQueueTrafficParams *pQueueTrafficParams; /**< */
/* Security related parameters */
#ifdef XCC_MODULE_INCLUDED
TI_BOOL rsnXCCSwEncFlag; /**< */
TI_BOOL rsnXCCMicFieldFlag; /**< */
#endif
ECipherSuite rsnEncryptionStatus; /**< */
TI_UINT8 rsnHwEncDecrEnable; /**< 0- disable, 1- enable */
TSecurityKeys *pRsnKey; /**< */
TI_UINT8 rsnDefaultKeyID; /**< */
/* Measurements section */
TMediumOccupancy mediumOccupancy; /**< */
TI_BOOL halTxOpContinuation; /**< */
TTsfDtim fwTsfDtimInfo; /**< */
TInterrogateCmdCbParams interogateCmdCBParams; /**< */
TConfigCmdCbParams configureCmdCBParams; /**< */
TTxRatePolicy *pTxRatePlicy; /**< */
/* WARNING!!! This section is used to set/get internal params only. */
TI_UINT16 halCtrlAid; /**< */
ESoftGeminiEnableModes SoftGeminiEnable; /**< */
TSoftGeminiParams SoftGeminiParam; /**< */
TFmCoexParams tFmCoexParams; /**< */
TI_UINT32 halCtrlMaxRxMsduLifetime; /**< */
/* Beacon Broadcast options */
TBcnBrcOptions BcnBrcOptions; /**< */
/* PLT tests */
TI_STATUS PltRxCalibrationStatus; /**< */
/* CoexActivity */
TCoexActivity tTwdParamsCoexActivity; /**< */
} TTwdParamContents;
/** \struct TTwdParamInfo
* \brief TWD Parameters Information
*
* \par Description
*
* \sa TWD_SetParam
*/
typedef struct
{
TI_UINT32 paramType; /**< FW Parameter Information Identifier */
TI_UINT32 paramLength; /**< FW Parameter Length */
TTwdParamContents content; /**< FW Parameter content */
} TTwdParamInfo;
/** \struct TRxXferReserved
* \brief RX Xfer Reserved
*
* \par Description
*
* \sa
*/
typedef struct
{
ProcessIDTag_e packetType; /**< */
TI_UINT8 rxLevel; /**< */
TI_INT8 rssi; /**< */
TI_UINT8 SNR; /**< */
TI_UINT8 band; /**< */
TI_UINT32 TimeStamp; /**< */
EScanResultTag eScanTag; /**< */
} TRxXferReserved;
/** \struct TRxAttr
* \brief RX Attributes
*
* \par Description
*
* \sa
*/
typedef struct
{
PacketClassTag_enum ePacketType; /**< */
TI_STATUS status; /**< */
ERate Rate; /**< */
TI_UINT8 SNR; /**< */
TI_INT8 Rssi; /**< */
TI_UINT8 channel; /**< */
TI_UINT32 packetInfo; /**< */
ERadioBand band; /**< */
TI_UINT32 TimeStamp; /**< */
EScanResultTag eScanTag; /**< */
} TRxAttr;
/** \struct TGeneralInitParams
* \brief General Initialization Parameters
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT16 halCtrlListenInterval; /**< */
TI_UINT8 halCtrlCalibrationChannel2_4; /**< */
TI_UINT8 halCtrlCalibrationChannel5_0; /**< */
TI_UINT16 halCtrlRtsThreshold; /**< */
TI_UINT16 halCtrlFragThreshold; /**< */
TI_UINT32 halCtrlMaxTxMsduLifetime; /**< */
TI_UINT32 halCtrlMaxRxMsduLifetime; /**< */
ETxAntenna halCtrlTxAntenna; /**< */
ERxAntenna halCtrlRxAntenna; /**< */
TI_UINT8 halCtrlMacClock; /**< */
TI_UINT8 halCtrlArmClock; /**< */
TI_UINT16 halCtrlBcnRxTime; /**< */
TI_BOOL halCtrlRxEnergyDetection; /**< */
TI_BOOL halCtrlTxEnergyDetection; /**< */
TI_BOOL halCtrlEepromLessEnable; /**< */
TI_BOOL halCtrlRxDisableBroadcast; /**< */
TI_BOOL halCtrlRecoveryEnable; /**< */
TI_BOOL halCtrlFirmwareDebug; /**< */
TI_BOOL WiFiWmmPS; /**< */
TRxTimeOut rxTimeOut; /**< */
TI_UINT8 halCtrlRateFallbackRetry; /**< */
TI_BOOL b11nEnable; /**< */
TI_UINT16 TxCompletePacingThreshold; /**< */
TI_UINT16 TxCompletePacingTimeout; /**< */
TI_UINT16 RxIntrPacingThreshold; /**< */
TI_UINT16 RxIntrPacingTimeout; /**< */
TI_UINT32 uRxAggregPktsLimit; /**< */
TI_UINT8 hwAccessMethod; /**< */
TI_UINT8 maxSitesFragCollect; /**< */
TI_UINT8 packetDetectionThreshold; /**< */
TI_UINT32 nullTemplateSize; /**< */
TI_UINT32 disconnTemplateSize; /**< */
TI_UINT32 beaconTemplateSize; /**< */
TI_UINT32 probeRequestTemplateSize; /**< */
TI_UINT32 probeResponseTemplateSize; /**< */
TI_UINT32 PsPollTemplateSize; /**< */
TI_UINT32 qosNullDataTemplateSize; /**< */
TI_UINT32 tddRadioCalTimout; /**< */
TI_UINT32 CrtRadioCalTimout; /**< */
TI_UINT32 UseMboxInterrupt; /**< */
TI_UINT32 TraceBufferSize; /**< */
TI_BOOL bDoPrint; /**< */
TI_UINT8 StaMacAddress[MAC_ADDR_LEN]; /**< */
TI_BOOL TxFlashEnable; /**< */
TI_UINT8 RxBroadcastInPs; /**< */
TI_UINT8 ConsecutivePsPollDeliveryFailureThreshold; /**< */
TI_UINT8 TxBlocksThresholdPerAc[MAX_NUM_OF_AC];/**< */
TI_UINT16 BeaconRxTimeout; /**< */
TI_UINT16 BroadcastRxTimeout; /**< */
TI_UINT8 uRssiBeaconAverageWeight; /**< */
TI_UINT8 uRssiPacketAverageWeight; /**< */
TI_UINT8 uSnrBeaconAverageWeight; /**< */
TI_UINT8 uSnrPacketAverageWeight; /**< */
TI_UINT32 uHostClkSettlingTime; /**< */
TI_UINT8 uHostFastWakeupSupport; /**< */
THalCoexActivityTable halCoexActivityTable; /**< */
TFmCoexParams tFmCoexParams; /**< */
} TGeneralInitParams;
/** \struct TPowerSrvInitParams
* \brief Power Service Init Parameters
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT8 numNullPktRetries; /**< */
TI_UINT8 hangOverPeriod; /**< */
TI_UINT16 reserve; /**< */
} TPowerSrvInitParams;
/** \struct TScanSrvInitParams
* \brief Scan Service Init Parameters
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT32 numberOfNoScanCompleteToRecovery; /**< The number of consecutive no scan complete that will trigger a recovery notification */
TI_UINT32 uTriggeredScanTimeOut; /**< i.e. split scan. Time out for starting triggered scan between 2 channels */
} TScanSrvInitParams;
/** \struct TArpIpFilterInitParams
* \brief ARP IP Filter Init Parameters
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT32 isFilterEnabled; /**< */
TIpAddr addr; /**< */
} TArpIpFilterInitParams;
/** \struct TMacAddrFilterInitParams
* \brief AMC Address Filter Init Parameters
*
* \par Description
*
* \sa
*/
typedef struct
{
TI_UINT8 isFilterEnabled; /**< */
TI_UINT8 numOfMacAddresses; /**< */
TI_UINT16 reserve; /**< */
TMacAddr macAddrTable[MAX_MULTICAST_GROUP_ADDRS]; /**< */
} TMacAddrFilterInitParams;
/** \struct RateMangeParams_t
* \brief Rate Maangement params structure
*
* \par Description
*
* \sa
*/
typedef struct
{
rateAdaptParam_e paramIndex;
uint16 RateRetryScore;
uint16 PerAdd;
uint16 PerTh1;
uint16 PerTh2;
uint16 MaxPer;
uint8 InverseCuriosityFactor;
uint8 TxFailLowTh;
uint8 TxFailHighTh;
uint8 PerAlphaShift;
uint8 PerAddShift;
uint8 PerBeta1Shift;
uint8 PerBeta2Shift;
uint8 RateCheckUp;
uint8 RateCheckDown;
uint8 RateRetryPolicy[13];
}RateMangeParams_t;
/*
* IMPORTANT NOTE:
* ===============
* This structure encapsulates the initialization data required by the TnetwDrv layer.
* All structures in it are arranged so no padding will be added by the compiler!!
* This is required to avoid missalignment when compiled by customers using GWSI API!!
*/
/** \struct TTwdInitParams
* \brief TWD Init Parameters
*
* \par Description
* All TWD Initialization Parameters
*
* \sa TWD_SetDefaults
*/
typedef struct
{
TGeneralInitParams tGeneral; /**< General Initialization Parameters */
TPowerSrvInitParams tPowerSrv; /**< Power Service Initialization Parameters */
TScanSrvInitParams tScanSrv; /**< Scan Service Initialization Parameters */
TArpIpFilterInitParams tArpIpFilter; /**< ARP IP filter Initialization Parameters */
TMacAddrFilterInitParams tMacAddrFilter; /**< MAC Address Initialization Parameters */
IniFileRadioParam tIniFileRadioParams; /**< Radio Initialization Parameters */
IniFileGeneralParam tPlatformGenParams; /**< Radio Initialization Parameters */
ACXSmartReflexConfigParams_t tSmartReflexParams; /**< Smart Refelx Parameters */
ACXSmartReflexDebugParams_t tSmartReflexDebugParams; /**< Smart Refelx Debug Parameters */
ACXSmartReflexState_t tSmartReflexState; /**< Smart Refelx state */
RateMangeParams_t tRateMngParams;
} TTwdInitParams;
/** \struct TTwdHtCapabilities
* \brief TWD HT Capabilities
*
* \par Description
*
* \sa TWD_SetDefaults, TWD_GetTwdHtCapabilities
*/
typedef struct
{
TI_BOOL b11nEnable; /**< Enable/Disable 802.11n flag */
TI_UINT8 uChannelWidth; /**< */
TI_UINT8 uRxSTBC; /**< */
TI_UINT8 uMaxAMSDU; /**< */
TI_UINT8 uMaxAMPDU; /**< */
TI_UINT8 uAMPDUSpacing; /**< */
TI_UINT8 aRxMCS[RX_TX_MCS_BITMASK_SIZE]; /**< */
TI_UINT8 aTxMCS[RX_TX_MCS_BITMASK_SIZE]; /**< */
TI_UINT16 uRxMaxDataRate; /**< */
TI_UINT8 uPCOTransTime; /**< */
TI_UINT32 uHTCapabilitiesBitMask; /**< */
TI_UINT8 uMCSFeedback; /**< */
} TTwdHtCapabilities;
typedef struct
{
int32 SNRCorrectionHighLimit;
int32 SNRCorrectionLowLimit;
int32 PERErrorTH;
int32 attemptEvaluateTH;
int32 goodAttemptTH;
int32 curveCorrectionStep;
}RateMangeReadParams_t;
/*
* --------------------------------------------------------------
* APIs
* --------------------------------------------------------------
*/
/** @ingroup Control
* \brief Send Packet Transfer CB
*
* \param CBObj - object handle
* \param pPktCtrlBlk - Pointer to Input Packet Control Block
* \return void
*
* \par Description
* The Transfer-Done callback
* User registers the CB for Send Packet Transfer done
*
* \sa TWD_RegisterCb
*/
typedef void (* TSendPacketTranferCb)(TI_HANDLE CBObj, TTxCtrlBlk *pPktCtrlBlk);
/** @ingroup Control
* \brief Send Packet Debug CB
*
* \param CBObj - object handle
* \param pPktCtrlBlk - Pointer to Input Packet Control Block
* uDebugInfo - Debug Information
* \return void
*
* \par Description
* The Transfer-Done Debug callback
*
* \sa
*/
typedef void (* TSendPacketDebugCb) (TI_HANDLE CBObj, TTxCtrlBlk *pPktCtrlBlk, TI_UINT32 uDebugInfo);
/** @ingroup Control
* \brief Send Packet Debug CB
*
* \param CBObj - object handle
* \param pPktCtrlBlk - Pointer to Input Packet Control Block
* uDebugInfo - Debug Information
* \return void
*
* \par Description
*
* \sa TWD_RegisterCb
*/
typedef ERxBufferStatus (*TRequestForBufferCb) (TI_HANDLE hObj, void **pRxBuffer, TI_UINT16 aLength, TI_UINT32 uEncryptionFlag, PacketClassTag_e ePacketClassTag);
/** @ingroup Control
* \brief Send Packet Debug CB
*
* \param hObj - object handle
* \param pBuffer - Pointer to Received buffer frame
* \return void
*
* \par Description
* This function CB will be called when Received packet from RX Queue
* User registers the CB for RX Buffer Request
*
* \sa TWD_RegisterCb
*/
typedef void (*TPacketReceiveCb) (TI_HANDLE hObj,
const void *pBuffer);
/** @ingroup Control
* \brief Failure Event CB
*
* \param handle - object handle
* \param eFailureEvent - Failure Event Type
* \return void
*
* \par Description
* Callback clled for Failure event
* User registers the CB for Health-Moitoring
*
* \sa TWD_RegisterCb
*/
typedef void (*TFailureEventCb) (TI_HANDLE handle, EFailureEvent eFailureEvent);
/** \union TTwdCB
* \brief TWD Callback
*
* \par Description
* Union which holds all TWD Internal Callbacks which are registered by user
* per Module and Event IDs
*
* \sa TWD_RegisterCb
*/
typedef union
{
TSendPacketTranferCb sendPacketCB; /**< Transfer-Done callback */
TSendPacketDebugCb sendPacketDbgCB; /**< Transfer-Done Debug callback */
TRequestForBufferCb requestBufferCB; /**< Transfer-Done Debug callback */
TPacketReceiveCb recvPacketCB; /**< RX Buffer Request callback */
TFailureEventCb failureEventCB; /**< Failure Event callback */
}TTwdCB;
/** @ingroup Control
* \brief Scan Service complete CB
*
* \param hCb - handle to the scan object
* \param eTag - the scan results type tag
* \param uResultCount - number of results received during this scan
* \param SPSStatus - bitmap indicating which channels were attempted (if this is an SPS scan)
* \param TSFError - whether a TSF error occurred (if this is an SPS scan)
* \param ScanStatus - scan SRV status (OK / NOK)
* \param PSMode - Power Save Mode
* \return void
*
* \par Description
* This function CB will be called when Scan Service is complete
* User registers the Scan Service Complete CB
*
* \sa TWD_RegisterScanCompleteCb
*/
typedef void (*TScanSrvCompleteCb) (TI_HANDLE hCb,
EScanResultTag eTag,
TI_UINT32 uResultCount,
TI_UINT16 SPSStatus,
TI_BOOL TSFError,
TI_STATUS ScanStatus,
TI_STATUS PSMode);
/** @ingroup Control
* \brief TWD Callback
*
* \param hCb - handle to object
* \param status - completion status
* \return void
*
* \par Description
* Initialising Complete Callaback (exapmle: Init HW/FW CB etc.)
* User can use its own Complete CB which will be called when
* the suitable module id & event number will arrive
*
* \sa TWD_Init
*/
typedef void (*TTwdCallback) (TI_HANDLE hCb, TI_STATUS status);
/** @ingroup Control
* \brief TWD Callback
*
* \param hCb - handle to object
* \param msrReply - Pointer to input measurement (which ended) Reply
* \return void
*
* \par Description
* The function prototype for the measurement complete callback
* User can use its own measurement complete CB
* which will be called when measurement end
*
* \sa TWD_StartMeasurement
*/
typedef void (*TMeasurementSrvCompleteCb) (TI_HANDLE hCb, TMeasurementReply* msrReply);
/** @ingroup Control
* \brief Command Response Callback
*
* \param hCb - handle to object
* \param status - status of Command ended
* \return void
*
* \par Description
* The function prototype for the Command Response CB
* Enables user to implement and use its own Response CB
* which will be called when TWD Command end
*
* \sa TWD_StartMeasurement, TWD_StopMeasurement, TWD_Scan, TWD_StopScan, TWD_StartPeriodicScan, TWD_StopPeriodicScan
*/
typedef void (*TCmdResponseCb) (TI_HANDLE hCb, TI_UINT16 status);
/** @ingroup Control
* \brief Command Response Callback
*
* \param hCb - handle to object
* \param status - status of Command ended
* \return void
*
* \par Description
* The function prototype for the Power Save Set Response CB
* Enables user to implement and use its own Response CB which
* will be called when Power Save Set Command end
*
* \sa TWD_SetPsMode
*/
typedef void (*TPowerSaveResponseCb)(TI_HANDLE hCb, TI_UINT8 status);
/** @ingroup Control
* \brief Command Complete Callback
*
* \param hCb - handle to object
* \param PsMode - Power Save Mode
* \param status - status of Command ended
* \return void
*
* \par Description
* The function prototype for the Power Save Set Complete CB
* Enables user to implement and use its own Complete CB which
* will be called when Power Save Set Command end (for success/faild notification)
*
* \sa TWD_SetPsMode
*/
typedef void (*TPowerSaveCompleteCb )(TI_HANDLE hCb, TI_UINT8 PsMode, TI_UINT8 status);
/** @ingroup Control
* \brief Create TWD Module
*
* \param hOs - OS module object handle
* \return TWD Module object handle on success or NULL on failure
*
* \par Description
* Calling this function Creates a TWD object and all its sub-modules.
*
* \sa TWD_Destroy, TWD_Init
*/
TI_HANDLE TWD_Create (TI_HANDLE hOs);
/** @ingroup Control
* \brief Destroy TWD Module
*
* \param hTWD - hTWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Calling this function Destroys TWD object and all its sub-modules.
*
* \sa TWD_Create
*/
TI_STATUS TWD_Destroy (TI_HANDLE hTWD);
/** Control
* \brief Init TWD module
*
* \param hTWD - TWD module object handle
* \param hReport - Report module object handle
* \param hUser - Master (User) module object handle
* \param hTimer - Timer module object handle
* \param hContext - context-engine module object handle
* \param hTxnQ - TxnQueue module object handle
* \param fInitHwCb - Init HW callback called when init HW phase is done
* \param fInitFwCb - Init FW callback called when init FW phase is done
* \param fConfigFwCb - Configuration FW callback called when configuring FW phase is done
* \param fStopCb - Stop callback called when TWD is stopped
* \param fInitFailCb - Fail callback called when TWD is Failed
* \return void
*
* \par Description
* Start hardware Init and Config process.
* This is the first function that must be called after TWD_Create.
*
* \sa TWD_Create, TWD_Stop
*/
void TWD_Init (TI_HANDLE hTWD,
TI_HANDLE hReport,
TI_HANDLE hUser,
TI_HANDLE hTimer,
TI_HANDLE hContext,
TI_HANDLE hTxnQ,
TTwdCallback fInitHwCb,
TTwdCallback fInitFwCb,
TTwdCallback fConfigFwCb,
TTwdCallback fStopCb,
TTwdCallback fInitFailCb);
/** @ingroup Control
* \brief Init HW module
*
* \param hTWD - TWD module object handle
* \param pbuf - Pointer to Input NVS Buffer
* \param length - Length of NVS Buffer
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Performs the HW init process.
*
* \sa
*/
TI_STATUS TWD_InitHw (TI_HANDLE hTWD, TI_UINT8 *pbuf, TI_UINT32 length);
/** @ingroup Control
* \brief Set Defults to TWD Init Params
*
* \param hTWD - TWD module object handle
* \param pInitParams - Pointer to Input init default parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_SetDefaults (TI_HANDLE hTWD, TTwdInitParams *pInitParams);
/** @ingroup Control
* \brief Init FW
*
* \param hTWD - TWD module object handle
* \param pFileInfo - Pointer to Input Buffer contains part of FW Image to Download
* The Following Field should be filled:
* pFileInfo->pBuffer
* pFileInfo->uLength
* pFileInfo->uAddress
* pFileInfo->bLast
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Performs FW Download, and Run FW
*
* \sa
*/
TI_STATUS TWD_InitFw (TI_HANDLE hTWD, TFileInfo *pFileInfo);
/** @ingroup Control
* \brief Open UART Bus Txn
*
* \param hTWD - TWD module object handle
* \param pParams - Pointer to Input parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_BusOpen (TI_HANDLE hTWD, void* pParams);
/** @ingroup Control
* \brief Close UART Bus Txn
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_BusClose (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Halt firmware
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_Stop (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Enable external events from FW
*
* \param hTWD - TWD module object handle
* \return void
*
* \par Description
* Enable external events from FW upon driver start or recovery completion
*
* \sa
*/
void TWD_EnableExternalEvents (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Registers TWD internal callback function
*
* \param hTWD - TWD module object handle
* \param event - event on which the registrated CB will be called
* \param fCb - Pointer to Registered CB function
* \param pData - Pointer to Registered CB data
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* This CB enables user to register TWD Internal CB functions of different Modules,
* with their data.
* The function identifies which TWD Module owns the Registered CB, and what the specific Registered CB
* according to event input parameter.
* Once the Module and specific CB function are identified, the CB is registerd in the TWD Module
* by calling suitable registration CB function
*
* \sa
*/
TI_STATUS TWD_RegisterCb (TI_HANDLE hTWD, TI_UINT32 event, TTwdCB *fCb, void *pData);
/** @ingroup Control
* \brief Exit from init mode
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Exit From Init Mode enable sending command to the MboxQueue (which store a command),
* while the interrupts are masked.
* The interrupt would be enable at the end of the init process
*
* \sa
*/
TI_STATUS TWD_ExitFromInitMode (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Finalize FW init and download
*
* \param hTWD - TWD module object handle
* \return void
*
* \par Description
* Init all the remaining initialization after the FW download has finished
*
* \sa
*/
void TWD_FinalizeDownload (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Finalize of faulty FW init and download
*
* \param hTWD - TWD module object handle
* \return void
*
* \par Description
* Call the upper layer failure callback after Init or FW download has finished with failure.
*
* \sa
*/
void TWD_FinalizeOnFailure (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Perform FW Configuration
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure the FW from the TWD DB - after configuring all HW objects
*
* \sa
*/
TI_STATUS TWD_ConfigFw (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Handle FW interrupt from ISR context
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* This is the FW-interrupt ISR context. The driver task is scheduled to hadnle FW-Events
*
* \sa
*/
TI_STATUS TWD_InterruptRequest (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Enable Recovery
*
* \param hTWD - TWD module object handle
* \return TRUE if recovery Enables, FALSE otherwise
*
* \par Description
* Return Recovery E/D status
*
* \sa
*/
TI_BOOL TWD_RecoveryEnabled (TI_HANDLE hTWD);
/** @ingroup Measurement
* \brief Starts a measurement
*
* \param hTWD - TWD module object handle
* \param pMsrRequest - Pointer to Input structure which contains the measurement parameters
* \param uTimeToRequestExpiryMs - The time (in milliseconds) the measurement SRV has to start the request
* \param fResponseCb - The Command response CB Function
* \param hResponseCb - Handle to Command response CB Function Obj
* \param fCompleteCb - The Command Complete CB Function
* \param hCompleteCb - Handle to Command Complete CB Function Obj
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Starts a measurement operation
*
* \sa
*/
TI_STATUS TWD_StartMeasurement (TI_HANDLE hTWD,
TMeasurementRequest *pMsrRequest,
TI_UINT32 uTimeToRequestExpiryMs,
TCmdResponseCb fResponseCb,
TI_HANDLE hResponseCb,
TMeasurementSrvCompleteCb fCompleteCb,
TI_HANDLE hCompleteCb);
/** @ingroup Measurement
* \brief Stops a measurement
*
* \param hTWD - TWD module object handle
* \param bSendNullData - Indicates whether to send NULL data when exiting driver mode
* \param fResponseCb - Pointer to Command response CB function
* \param hResponseCb - Handle to Command response CB parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Stops a measurement operation in progress
*
* \sa
*/
TI_STATUS TWD_StopMeasurement (TI_HANDLE hTWD,
TI_BOOL bSendNullData,
TCmdResponseCb fResponseCb,
TI_HANDLE hResponseCb);
/** @ingroup Measurement
* \brief Start scan
*
* \param hTWD - TWD module object handle
* \param pScanParams - Pointer to Input Scan specific parameters
* \param eScanTag - Scan tag, used for result and scan complete tracking
* \param bHighPriority - Indicates whether to perform a high priority (overlaps DTIM) scan
* \param bDriverMode - Indicates whether to try to enter driver mode (with PS on) before issuing the scan command
* \param bScanOnDriverModeError - Indicates whether to proceed with the scan if requested to enter driver mode and failed
* \param ePsRequest - Parameter sent to PowerSaveServer.
* Should indicates PS ON or "keep current" only when driver mode is requested,
* Otherwise should indicate OFF
* \param bSendNullData - Indicates whether to send Null data when exiting driver mode on scan complete
* \param fResponseCb - The Response CB Function which called after downloading the command
* \param hResponseCb - Handle to the Response CB Function Obj (Notice : last 2 params are NULL in Legacy run)
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Start scan. enter driver mode (PS) only if station is connected
*
* \sa
*/
TI_STATUS TWD_Scan (TI_HANDLE hTWD,
TScanParams *pScanParams,
EScanResultTag eScanTag,
TI_BOOL bHighPriority,
TI_BOOL bDriverMode,
TI_BOOL bScanOnDriverModeError,
E80211PsMode ePsRequest,
TI_BOOL bSendNullData,
TCmdResponseCb fResponseCb,
TI_HANDLE hResponseCb);
/** @ingroup Measurement
* \brief Stop scan
*
* \param hTWD - TWD module object handle
* \param eScanTag - Scan tag, used to track scan complete and result
* \param bSendNullData - Indicates whether to send Null data when exiting driver mode
* \param fScanCommandResponseCb - The Response CB Function which called after downloading the command
* \param hCb - Handle to the Response CB Function Obj (Notice : last 2 params are NULL in Legacy run)
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Sends a Stop Scan command to FW, no matter if we are in scan progress or not
*
* \sa
*/
TI_STATUS TWD_StopScan (TI_HANDLE hTWD,
EScanResultTag eScanTag,
TI_BOOL bSendNullData,
TCmdResponseCb fScanCommandResponseCb,
TI_HANDLE hCb);
/** @ingroup Measurement
* \brief Stop Scan on FW Reset
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Stop scan operation when a FW reset (recovery) situation is detected (by all processes
* other than scan)
*
* \sa
*/
TI_STATUS TWD_StopScanOnFWReset (TI_HANDLE hTWD);
/** @ingroup Measurement
* \brief Start Connection Periodic Scan operation
*
* \param hTWD - TWD module object handle
* \param pPeriodicScanParams - Pointer to Input Parameters Structures for the Periodic Scan operation
* \param eScanTag - Scan tag, used for scan complete and result tracking
* \param uPassiveScanDfsDwellTimeMs - Passive dwell time for DFS channels (in milli-secs)
* \param fResponseCb - Response CB Function which is called after downloading the command
* \param hResponseCb - Handle to Response CB Function Obj (Notice : last 2 params are NULL in Legacy run)
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Perform Connection Scan periodically
*
* \sa
*/
TI_STATUS TWD_StartConnectionScan (TI_HANDLE hTWD,
TPeriodicScanParams *pPeriodicScanParams,
EScanResultTag eScanTag,
TI_UINT32 uPassiveScanDfsDwellTimeMs,
TCmdResponseCb fResponseCb,
TI_HANDLE hResponseCb);
/** @ingroup Measurement
* \brief Stop Periodic Scan operation
*
* \param hTWD - TWD module object handle
* \param eScanTag - scan tag, used for scan complete and result tracking
* \param fResponseCb - Response CB Function which is called after downloading the command
* \param hResponseCb - Handle to Response CB Function Obj (Notice : last 2 params are NULL in Legacy run)
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Stop Periodic Connection Scan
*
* \sa
*/
TI_STATUS TWD_StopPeriodicScan (TI_HANDLE hTWD,
EScanResultTag eScanTag,
TCmdResponseCb fResponseCb,
TI_HANDLE hResponseCb);
/** @ingroup Measurement
* \brief Register CB for Scan Complete
*
* \param hTWD - TWD module object handle
* \param fScanCompleteCb - The Complete CB Function
* \param hScanCompleteCb - Handle to the Complete CB Function Obj
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Registers a Complete CB Function for Scan Complete notifications
*
* \sa
*/
TI_STATUS TWD_RegisterScanCompleteCb (TI_HANDLE hTWD,
TScanSrvCompleteCb fScanCompleteCb,
TI_HANDLE hScanCompleteCb);
/** @ingroup Misc
* \brief Set Parameters in FW
*
* \param hTWD - TWD module object handle
* \param pParamInfo - Pointer to Input TWD Parameters Information Structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Set/Configure Parameters Information in FW via Mail BOX
*
* \sa TTwdParamInfo
*/
TI_STATUS TWD_SetParam (TI_HANDLE hTWD, TTwdParamInfo *pParamInfo);
/** @ingroup Misc
* \brief Get Parameters from FW
*
* \param hTWD - TWD module object handle
* \param pParamInfo - Pointer to Input TWD Parameters Information Structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Get Parameters Information from FW via Mail BOX
*
* \sa
*/
TI_STATUS TWD_GetParam (TI_HANDLE hTWD, TTwdParamInfo *pParamInfo);
/** @ingroup Control
* \brief Callback which Checks MBOX
*
* \param hTWD - TWD module object handle
* \param uMboxStatus - Mailbox status
* \param pItrParamBuf - Pointer to Interrogate parameters buffer
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Perform FW validation by calling CB function which is used for handling MBOX error.
* If command MBOX queue identify MBOX error or timeout, it will call
* a failure-callback with MBOX_FAILURE type (FW failed)
*
* \sa
*/
TI_STATUS TWD_CheckMailboxCb (TI_HANDLE hTWD, TI_UINT16 uMboxStatus, void *pItrParamBuf);
/** @ingroup Control
* \brief Write MIB
*
* \param hTWD - TWD module object handle
* \param pMib - Pointer to Input MIB Structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Write configuration information to FW
*
* \sa TWD_ReadMib
*/
TI_STATUS TWD_WriteMib (TI_HANDLE hTWD, TMib* pMib);
/** @ingroup Control
* \brief Read MIB
*
* \param hTWD - TWD module object handle
* \param hCb - Handle to Request MIB CB Function Obj
* \param fCb - Pinter to Request MIB CB Function
* \param pCb - Pointer to read parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Read configuration information from FW
*
* \sa TWD_WriteMib
*/
TI_STATUS TWD_ReadMib (TI_HANDLE hTWD, TI_HANDLE hCb, void* fCb, void* pCb);
/** @ingroup Control
* \brief TWD Debug
*
* \param hTWD - TWD module object handle
* \param funcType - TWD Function Debuged
* \param pParam - Pointer to Input parameters of Debug function
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Use for Debug TWD
*
* \sa
*/
TI_STATUS TWD_Debug (TI_HANDLE hTWD, TI_UINT32 funcType, void *pParam);
/** @ingroup Control
* \brief Register event
*
* \param hTWD - TWD module object handle
* \param event - Event ID
* \param fCb - Event Callback function pointer
* \param hCb - Event Callback object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Register FW event callback function
*
* \sa
*/
TI_STATUS TWD_RegisterEvent (TI_HANDLE hTWD, TI_UINT32 event, void *fCb, TI_HANDLE hCb);
/** @ingroup Control
* \brief Disable event
*
* \param hTWD - TWD module object handle
* \param event - Event ID
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Disable specific FW event
* Note: Currently not in use
*
* \sa
*/
TI_STATUS TWD_DisableEvent (TI_HANDLE hTWD, TI_UINT32 event);
/** @ingroup Control
* \brief Enable event
*
* \param hTWD - TWD module object handle
* \param event - Event ID
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Enable specific FW event
*
* \sa
*/
TI_STATUS TWD_EnableEvent (TI_HANDLE hTWD, TI_UINT32 event);
/** @ingroup Control
* \brief Convert RSSI to RX Level
*
* \param hTWD - TWD module object handle
* \param iRssiVal - RSSI Input Value
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Note: Currently not in use!
*
* \sa
*/
TI_INT8 TWD_ConvertRSSIToRxLevel (TI_HANDLE hTWD, TI_INT32 iRssiVal);
/** @ingroup Control
* \brief Complete TWD Stop
*
* \param hTWD - TWD module object handle
* \return void
*
* \par Description
*
* \sa TWD_Stop, TWD_Init
*/
void TWD_StopComplete (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Disable Interrupts
*
* \param hTWD - TWD module object handle
* \return void
*
* \par Description
* Disable the FW Event client of the context thread handler
*
* \sa
*/
void TWD_DisableInterrupts (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Enable Interrupts
*
* \param hTWD - TWD module object handle
* \return void
*
* \par Description
* Enable the FW Event client of the context thread handler
*
* \sa
*/
void TWD_EnableInterrupts (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Translate host to FW time (Usec)
*
* \param hTWD - TWD module object handle
* \param uHostTime - The host time in MS to translate
*
* \return FW Time in Usec
*
* \par Description
*
* \sa
*/
TI_UINT32 TWD_TranslateToFwTime (TI_HANDLE hTWD, TI_UINT32 uHostTime);
/** @ingroup BSS
* \brief Get TWD HT Capabilities
*
* \param hTWD - TWD module object handle
* \param pTwdHtCapabilities - Pointer read structure Output
* \return TI_OK
*
* \par Description
*
*
* \sa
*/
void TWD_GetTwdHtCapabilities (TI_HANDLE hTWD, TTwdHtCapabilities **pTwdHtCapabilities);
#ifdef TI_DBG
/** @ingroup Measurement
* \brief Prints Scan Server Debug status
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_PrintMacServDebugStatus (TI_HANDLE hTWD);
/** @ingroup Test
* \brief Prints Tx Info
*
* \param hTWD - TWD module object handle
* \param ePrintInfo - Information type
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Call the requested print function - used for Debug Test
*
* \sa
*/
TI_STATUS TWD_PrintTxInfo (TI_HANDLE hTWD, ETwdPrintInfoType ePrintInfo);
#endif
/*-----*/
/* Get */
/*-----*/
/** @ingroup Control
* \brief Get number of Commands in CMD Queue
*
* \param hTWD - TWD module object handle
* \return Maximum Number of Commands currently in CMD Queue
*
* \par Description
*
* \sa
*/
TI_UINT32 TWD_GetMaxNumberOfCommandsInQueue (TI_HANDLE hTWD);
/** @ingroup Power_Management
* \brief Get Power Save Status
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_BOOL TWD_GetPsStatus (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Get FW Information
*
* \param hTWD - TWD module object handle
* \return TFwInfo - Pointer to Output FW Information Structure
*
* \par Description
* Gets the TFwInfo pointer
*
* \sa TFwInfo
*/
TFwInfo* TWD_GetFWInfo (TI_HANDLE hTWD);
/** @ingroup BSS
* \brief Get Group Address Table
*
* \param hTWD - TWD module object handle
* \param pEnabled - Pointer to Output Indicatore if MAC Address Filter is Enabled
* \param pNumGroupAddrs - Pointer to Output Number of Group Address
* \param pGroupAddr - Pointer to Output Group Address Table
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa TWD_WriteMib, TMacAddr
*/
TI_STATUS TWD_GetGroupAddressTable (TI_HANDLE hTWD, TI_UINT8* pEnabled, TI_UINT8* pNumGroupAddrs, TMacAddr *pGroupAddr);
/** @ingroup Control
* \brief Read Memory
*
* \param hTWD - TWD module object handle
* \param pMemDebug - Pointer to read Output
* \param fCb - Pointer to function Callback
* \param hCb - Handle to function Callback Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_readMem (TI_HANDLE hTWD, TFwDebugParams* pMemDebug, void* fCb, TI_HANDLE hCb);
/** @ingroup Control
* \brief Write Memory
*
* \param hTWD - TWD module object handle
* \param pMemDebug - Pointer to write Input
* \param fCb - Pointer to function Callback
* \param hCb - Handle to function Callback Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_writeMem (TI_HANDLE hTWD, TFwDebugParams* pMemDebug, void* fCb, TI_HANDLE hCb);
/** @ingroup Control
* \brief Check if addr is a valid memory address
*
* \param hTWD - TWD module object handle
* \param pMemDebug - Pointer to addr & length
* \return TI_TRUE on success or TI_FALSE on failure
*
* \par Description
*
* \sa
*/
TI_BOOL TWD_isValidMemoryAddr (TI_HANDLE hTWD, TFwDebugParams* pMemDebug);
/** @ingroup Control
* \brief Check if addr is a valid register address
*
* \param hTWD - TWD module object handle
* \param pMemDebug - Pointer to addr & length
* \return TI_TRUE on success or TI_FALSE on failure
*
* \par Description
*
* \sa
*/
TI_BOOL TWD_isValidRegAddr (TI_HANDLE hTWD, TFwDebugParams* pMemDebug);
/*-----*/
/* Set */
/*-----*/
/** @ingroup Power_Management
* \brief Set Power Save Mode
*
* \param hTWD - TWD module object handle
* \param ePsMode - Power Save Mode
* \param bSendNullDataOnExit - Indicates whether to send NULL data when exiting driver mode
* \param hPowerSaveCompleteCb - Handle to PS Complete CB Parameters Obj
* \param fPowerSaveCompleteCb - The PS Complete CB function
* \param fPowerSaveResponseCb - The PS Response CB function
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_SetPsMode (TI_HANDLE hTWD,
E80211PsMode ePsMode,
TI_BOOL bSendNullDataOnExit,
TI_HANDLE hPowerSaveCompleteCb,
TPowerSaveCompleteCb fPowerSaveCompleteCb,
TPowerSaveResponseCb fPowerSaveResponseCb);
/** @ingroup Radio
* \brief Set Rate Modulation
*
* \param hTWD - TWD module object handle
* \param rate - Rate Modulation Value
* \return TRUE if Power Service State is Pwer Save, FALSE otherwise
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_SetNullRateModulation (TI_HANDLE hTWD, TI_UINT16 rate);
/** @ingroup Radio
* \brief Set Radio Band
*
* \param hTWD - TWD module object handle
* \param eRadioBand - Radio Band Type
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_SetRadioBand (TI_HANDLE hTWD, ERadioBand eRadioBand);
/** @ingroup Data_Path
* \brief Set Security Sequance Number
*
* \param hTWD - TWD module object handle
* \param securitySeqNumLsByte - LS Byte of Security Sequance Number
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Update the TKIP/AES sequence-number according to the Tx data packet security-sequance-number
* Note: The FW always provides the last used sequance-number so no need to check if the current
* packet is data and WEP is on
*
* \sa
*/
TI_STATUS TWD_SetSecuritySeqNum (TI_HANDLE hTWD, TI_UINT8 securitySeqNumLsByte);
/** @ingroup BSS
* \brief Update DTIM & TBTT
*
* \param hTWD - TWD module object handle
* \param uDtimPeriod - DTIM period in number of beacons
* \param uBeaconInterval - Beacon perios in TUs (1024 msec)
* \return void
*
* \par Description
* Update DTIM and Beacon periods for scan timeout calculations
*
* \sa
*/
void TWD_UpdateDtimTbtt (TI_HANDLE hTWD, TI_UINT8 uDtimPeriod, TI_UINT16 uBeaconInterval);
/*---------*/
/* Command */
/*---------*/
/** @ingroup Measurement
* \brief Set Split scan time out
*
* \param hTWD - TWD module object handle
* \param uTimeOut - Scan Time Out
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Set Triggered scan time out per channel
*
* \sa
*/
TI_STATUS TWD_CmdSetSplitScanTimeOut (TI_HANDLE hTWD, TI_UINT32 uTimeOut);
/** @ingroup BSS
* \brief Join BSS
*
* \param hTWD - TWD module object handle
* \param pJoinBssParams - Pointer to Join BSS Input parameters structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CmdJoinBss (TI_HANDLE hTWD, TJoinBss *pJoinBssParams);
/** @ingroup Control
* \brief Command Template
*
* \param hTWD - TWD module object handle
* \param pTemplateParams - Pointer to Input Template Parameters Structure
* \param fCb - Pointer to Command Callback Function
* \param hCb - Handle to Command Callback Function Obj. Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Sets a template to the FW
*
* \sa
*/
/* 6.1.08 - for future WHA measurement command */
TI_STATUS TWD_CmdTemplate (TI_HANDLE hTWD, TSetTemplate *pTemplateParams, void *fCb, TI_HANDLE hCb);
/** @ingroup Data_Path
* \brief Enable Tx path
*
* \param hTWD - TWD module object handle
* \param channel - Channel Number
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Enable tx path on the hardware
*
* \sa
*/
TI_STATUS TWD_CmdEnableTx (TI_HANDLE hTWD, TI_UINT8 channel);
/** @ingroup Data_Path
* \brief Disable Tx path
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CmdDisableTx (TI_HANDLE hTWD);
/** @ingroup Measurement
* \brief Command Noise Histogram
*
* \param hTWD - TWD module object handle
* \param pNoiseHistParams - Pointer Input Noise Histogram Parameters:
* holds Start/Stop Noise Histogram Measure Indication,
* Sample Interval & Sample Ranges
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Send a Start/Stop Noise Histogram Measure Command to the FW with measure parameters
*
* \sa TNoiseHistogram
*/
TI_STATUS TWD_CmdNoiseHistogram (TI_HANDLE hTWD, TNoiseHistogram *pNoiseHistParams);
/** @ingroup Radio
* \brief Command Switch Channel
*
* \param hTWD - TWD module object handle
* \param pSwitchChannelCmd - Pointer to Switch Channel Parameters Structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa TSwitchChannelParams
*/
TI_STATUS TWD_CmdSwitchChannel (TI_HANDLE hTWD, TSwitchChannelParams *pSwitchChannelCmd);
/** @ingroup Radio
* \brief Command Switch Channel Cancel
*
* \param hTWD - TWD module object handle
* \param channel - Channek Number
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CmdSwitchChannelCancel (TI_HANDLE hTWD, TI_UINT8 channel);
/** @ingroup Control
* \brief FW Disconnect
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CmdFwDisconnect (TI_HANDLE hTWD, DisconnectType_e uDisconType, TI_UINT16 uDisconReason);
/** @ingroup Measurement
* \brief Start Measurement Command
*
* \param hTWD - TWD module object handle
* \param uDisconReason - 2 bytes of disconnect reason to be use in deauth/disassoc frmaes
* \param uDisconType - Immediate (dont send frames) or send Deauth or send Disassoc frmae
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* send Command for start measurement to FW
*
* \sa TMeasurementParams
*/
TI_STATUS TWD_CmdMeasurement (TI_HANDLE hTWD,
TMeasurementParams *pMeasurementParams,
void *fCommandResponseCb,
TI_HANDLE hCb);
/** @ingroup Measurement
* \brief Stop Measurement Command
*
* \param hTWD - TWD module object handle
* \param fCb - Pointer to Callback Function
* \param hCb - Handle to Callback Function Object Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* send Command for stop measurement to FW
*
* \sa
*/
TI_STATUS TWD_CmdMeasurementStop (TI_HANDLE hTWD, void* fCb, TI_HANDLE hCb);
/** @ingroup UnKnown
* \brief AP Discovery
*
* \param hTWD - TWD module object handle
* \param pApDiscoveryParams - Pointer to Input AP Discovery Parameters Structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CmdApDiscovery (TI_HANDLE hTWD, TApDiscoveryParams *pApDiscoveryParams);
/** @ingroup UnKnown
* \brief AP Discovery Stop
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CmdApDiscoveryStop (TI_HANDLE hTWD);
/** @ingroup Control
* \brief Helth Check
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Trigger the FW health test command and wait for results
*
* \sa
*/
TI_STATUS TWD_CmdHealthCheck (TI_HANDLE hTWD);
/** @ingroup UnKnown
* \brief AP Discovery
*
* \param hTWD - TWD module object handle
* \param staState - stat of the station (CONNECTED)
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CmdSetStaState (TI_HANDLE hTWD, TI_UINT8 staState, void *fCb, TI_HANDLE hCb);
/*-----------*/
/* Configure */
/*-----------*/
/** @ingroup UnKnown
* \brief Configure ARP table
*
* \param hTWD - TWD module object handle
* \param tIpAddr - IP Address Input Buffer
* \param bEnabled - Indicates if ARP filtering is Enabled (1) or Disabled (0)
* \param eIpVer - IP Version
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure ARP IP Address table
*
* \sa
*/
TI_STATUS TWD_CfgArpIpAddrTable (TI_HANDLE hTWD,
TIpAddr tIpAddr,
TI_BOOL bEnabled,
EIpVer eIpVer);
/** @ingroup BSS
* \brief Configure Group Address Table
*
* \param hTWD - TWD module object handle
* \param uNumGroupAddrs - Number of Group Address
* \param pGroupAddr - Pointer to Input Group Address Table
* \param bEnabled - Indicates if MAC Address Filter is Enabled
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa TWD_WriteMib
*/
TI_STATUS TWD_CfgGroupAddressTable (TI_HANDLE hTWD,
TI_UINT8 uNumGroupAddrs,
TMacAddr *pGroupAddr,
TI_BOOL bEnabled);
/** @ingroup Data_Path
* \brief Configure RX Filters
*
* \param hTWD - TWD module object handle
* \param uRxConfigOption - RX Configuration Option
* \param uRxFilterOption - RX Filter Option
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa TWD_WriteMib
*/
TI_STATUS TWD_CfgRx (TI_HANDLE hTWD, TI_UINT32 uRxConfigOption, TI_UINT32 uRxFilterOption);
/** @ingroup UnKnown
* \brief Configure Packet Detection Threshold
*
* \param hTWD - TWD module object handle
* \param threshold - Threshold Value
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa ERate
*/
TI_STATUS TWD_CfgPacketDetectionThreshold (TI_HANDLE hTWD, TI_UINT32 threshold);
/** @ingroup Radio
* \brief Configure Slot Time
*
* \param hTWD - TWD module object handle
* \param eSlotTimeVal - Slot Time Value
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgSlotTime (TI_HANDLE hTWD, ESlotTime eSlotTimeVal);
/** @ingroup Radio
* \brief Configure Preamble
*
* \param hTWD - TWD module object handle
* \param ePreamble - Preamble Value
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgPreamble (TI_HANDLE hTWD, EPreamble ePreamble);
/** @ingroup Power_Management
* \brief Configure Beacon Filter State
*
* \param hTWD - TWD module object handle
* \param uBeaconFilteringStatus - Beacon Filtering Status. Indicates whether the filter is enabled:
* 1 - enabled, 0 - disabled
* \param uNumOfBeaconsToBuffer - Determines the number of beacons without the unicast TIM bit set,
* that the firmware buffers before signaling the host about ready frames.
* When thi snumber is set to 0 and the filter is enabled, beacons without
* the unicast TIM bit set are dropped.
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure Beacon Filter State to the FW
*
* \sa
*/
TI_STATUS TWD_CfgBeaconFilterOpt (TI_HANDLE hTWD, TI_UINT8 uBeaconFilteringStatus, TI_UINT8 uNumOfBeaconsToBuffer);
/** @ingroup Power_Management
* \brief Configure Beacon Filter Table
*
* \param hTWD - TWD module object handle
* \param uNumOfIe - The number of IE's in the table
* \param pIeTable - Pointer to Input IE Table
* \param uIeTableSize - Size of Input IE Table
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure Beacon Filter Table to the FW
*
* \sa
*/
TI_STATUS TWD_CfgBeaconFilterTable (TI_HANDLE hTWD, TI_UINT8 uNumOfIe, TI_UINT8 *pIeTable, TI_UINT8 uIeTableSize);
/** @ingroup Power_Management
* \brief Configure Wake Up Condition
*
* \param hTWD - TWD module object handle
* \param pPowerMgmtConfig - Pointer to Input Power Management Configuration Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure Power Manager's Wake Up Condition
*
* \sa
*/
TI_STATUS TWD_CfgWakeUpCondition (TI_HANDLE hTWD, TPowerMgmtConfig *pPowerMgmtConfig);
/** @ingroup UnKnown
* \brief Configure Beacon Broadcast Options
*
* \param hTWD - TWD module object handle
* \param pPowerMgmtConfig - Pointer to Input Power Management Configuration Parameters Structure
* The Following Field should be filled:
* pPowerMgmtConfig->BcnBrcOptions.BeaconRxTimeout
* pPowerMgmtConfig->BcnBrcOptions.BroadcastRxTimeout
* pPowerMgmtConfig->BcnBrcOptions.RxBroadcastInPs - if set, enables receive of broadcast packets in Power-Save mode
* pPowerMgmtConfig->ConsecutivePsPollDeliveryFailureThreshold - No answer after Ps-Poll work-around
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure Power Manager's Beacon Broadcast Options:
* Beacon RX time Out, Broadcast RX Timeout, RX Broadcast In Power Save,
* Consecutive Power Save Poll Delivery Failure Threshold
*
*
* \sa TPowerMgmtConfig, TBcnBrcOptions
*/
TI_STATUS TWD_CfgBcnBrcOptions (TI_HANDLE hTWD, TPowerMgmtConfig *pPowerMgmtConfig);
/** @ingroup BSS
* \brief Configure Max TX Retry
*
* \param hTWD - TWD module object handle
* \param pRoamingTriggerCmd - Pointer to Input Configuration Parameters Structure
* The Following Field should be filled:
* pRoamingTriggerCmd->maxTxRetry
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure the Max Tx Retry parameters
*
* \sa
*/
TI_STATUS TWD_CfgMaxTxRetry (TI_HANDLE hTWD, TRroamingTriggerParams *pRoamingTriggerCmd);
/** @ingroup BSS
* \brief Configure Connection Monitoring
*
* \param hTWD - TWD module object handle
* \param pRoamingTriggerCmd - Pointer to Input Configuration Parameters Structure
* The Following Field should be filled:
* pRoamingTriggerCmd->BssLossTimeout
* pRoamingTriggerCmd->TsfMissThreshold
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure the Bss Lost Timeout & TSF miss threshold Parameters
*
* \sa
*/
TI_STATUS TWD_CfgConnMonitParams (TI_HANDLE hTWD, TRroamingTriggerParams *pRoamingTriggerCmd);
/** @ingroup Power_Management
* \brief Configure Sleep Auth
*
* \param hTWD - TWD module object handle
* \param eMinPowerPolicy - Minimum Power Policy Type
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure the minimum power policy to the FW
*
* \sa EPowerPolicy
*/
TI_STATUS TWD_CfgSleepAuth (TI_HANDLE hTWD, EPowerPolicy eMinPowerPolicy);
/** @ingroup Control
* \brief Configure MAC Clock
*
* \param hTWD - TWD module object handle
* \param uMacClock - MAC Clock value
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgMacClock (TI_HANDLE hTWD, TI_UINT32 uMacClock);
/** @ingroup Control
* \brief Configure ARM Clock
*
* \param hTWD - TWD module object handle
* \param uArmClock - ARM Clock value
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgArmClock (TI_HANDLE hTWD, TI_UINT32 uArmClock);
/** @ingroup Data_Path
* \brief Configure RX Data Filter
*
* \param hTWD - TWD module object handle
* \param index - Index of the Rx Data filter
* \param command - Command: Add/remove the filter
* \param eAction - Action to take when packets match the pattern
* \param uNumFieldPatterns - Number of field patterns in the filter
* \param uLenFieldPatterns - Length of the field pattern series
* \param pFieldPatterns - Series of field patterns
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Add/remove Rx Data filter information element
*
* \sa
*/
TI_STATUS TWD_CfgRxDataFilter (TI_HANDLE hTWD,
TI_UINT8 index,
TI_UINT8 command,
filter_e eAction,
TI_UINT8 uNumFieldPatterns,
TI_UINT8 uLenFieldPatterns,
TI_UINT8 *pFieldPatterns);
/** @ingroup Data_Path
* \brief Configure Enable RX Data Filter
*
* \param hTWD - TWD module object handle
* \param bEnabled - Indicates if Rx data filtering is enabled or Disabled
* (0: data filtering disabled, Otherwise: enabled)
* \param eDefaultAction - The default action taken on non-matching packets
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure Enable/Disable RX Data Filter, and which default action to perform if it is enabled
*
* \sa
*/
TI_STATUS TWD_CfgEnableRxDataFilter (TI_HANDLE hTWD, TI_BOOL bEnabled, filter_e eDefaultAction);
/** @ingroup BSS
* \brief Configure RRSSI/SNR Trigger parameters
*
* \param hTWD - TWD module object handle
* \param pRssiSnrTrigger - Pointer to RRSSI/SNR Input parameter Structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgRssiSnrTrigger (TI_HANDLE hTWD, RssiSnrTriggerCfg_t* pRssiSnrTrigger);
/** @ingroup QoS
* \brief Configure AC parameters
*
* \param hTWD - TWD module object handle
* \param pAcQosParams - Pointer to Input AC Quality Of Service Parameters Structure
* Fields that should be filled:
* pAcQosParams->ac
* pAcQosParams->aifsn
* pAcQosParams->cwMax
* pAcQosParams->cwMin
* pAcQosParams->txopLimit
* \param fCb - Pointer to Command CB Function
* \param hCb - Handle to Command CB Function Obj Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgAcParams (TI_HANDLE hTWD, TAcQosParams *pAcQosParams, void *fCb, TI_HANDLE hCb);
/** @ingroup QoS
* \brief Configure Power Save RX Streaming
*
* \param hTWD - TWD module object handle
* \param pPsRxStreaming - Pointer to Input Power Save RX Straeming Parameters Structure
* Fields that should be filled:
* pPsRxStreaming->uTid
* pPsRxStreaming->bEnabled
* pPsRxStreaming->uStreamPeriod
* pPsRxStreaming->uTxTimeout
* \param fCb - Pointer to Command CB Function
* \param hCb - Handle to Command CB Function Obj Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa TPsRxStreaming
*/
TI_STATUS TWD_CfgPsRxStreaming (TI_HANDLE hTWD, TPsRxStreaming *pPsRxStreaming, void *fCb, TI_HANDLE hCb);
/** @ingroup Power_Management
* \brief Configure BET
*
* \param hTWD - TWD module object handle
* \param Enable - 0: disable BET, Otherwirs: Enable BET
* \param MaximumConsecutiveET - Max number of consecutive beacons that may be early terminated
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgBet (TI_HANDLE hTWD, TI_UINT8 Enable, TI_UINT8 MaximumConsecutiveET);
/** @ingroup UnKnown
* \brief Configure Keep Alive
*
* \param hTWD - TWD module object handle
* \param pKeepAliveParams - Pointer to Keep Alive parameters structure
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configures the keep-alive paramters
*
* \sa
*/
TI_STATUS TWD_CfgKeepAlive (TI_HANDLE hTWD, TKeepAliveParams *pKeepAliveParams);
/** @ingroup Power_Management
* \brief Configure Keep Alive Enable/Disable flag
*
* \param hTWD - TWD module object handle
* \param enaDisFlag - Indicates whether to Enable (TI_TRUE) or Disable Keep Alive
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgKeepAliveEnaDis (TI_HANDLE hTWD, TI_UINT8 enaDisFlag);
/** @ingroup Data_Path
* \brief Configure Set BA Initiator
*
* \param hTWD - TWD module object handle
* \param uTid - TID number
* \param uState - Policy : Enable / Disable
* \param tRa - Mac address of: SA as receiver / RA as initiator
* \param uWinSize - windows size in number of packet
* \param uInactivityTimeout - as initiator inactivity timeout in time units(TU) of 1024us / as receiver reserved
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* configure BA session initiator parameters setting in the FW
* called after join in order to init the parameters for negotiating BA sessions as initiator.
* Parameters initialized: RA, TID, WinSize, Inactivity Timeout and state = Enable/Disable.
* In case the host sends a broadcast address as RA the FW is allowed to Set or Deleted BA sessions
* to any receiver for that TID.
* In case of disassociate the FW allowed to establish BA session just after get that command.
* That command will not need any respond from the FW. In case DELBA send to STA or from the
* STA as initiator the FW doesn't send event to the host
*
* \sa
*/
TI_STATUS TWD_CfgSetBaInitiator (TI_HANDLE hTWD,
TI_UINT8 uTid,
TI_UINT8 uState,
TMacAddr tRa,
TI_UINT16 uWinSize,
TI_UINT16 uInactivityTimeout);
/** @ingroup Data_Path
* \brief Configure Set BA Receiver
*
* \param hTWD - TWD module object handle
* \param uTid - TID number
* \param uState - Policy : Enable / Disable
* \param tRa - Mac address of: SA as receiver / RA as initiator
* \param uWinSize - windows size in number of packet
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* configure BA session receiver parameters setting in the FW
* called after join in order to init the parameters for incoming BA session, as a responder.
* Parameters initialized: SA, TID, winSize and state = Enable/Disable.
* In case the host sends a broadcast address as SA the FW is allowed to Set/Deleted BA sessions
* to any sender for that TID.
* In case of disassociate the FW allowed to establish BA session just after get that command.
* The events of that command will respond via the RX path from the FW: ADDBA, DELBA, BAR packets.
*
* \sa
*/
TI_STATUS TWD_CfgSetBaReceiver (TI_HANDLE hTWD,
TI_UINT8 uTid,
TI_UINT8 uState,
TMacAddr tRa,
TI_UINT16 uWinSize);
/** @ingroup Data_Path
* \brief Close all BA receiver sessions
*
* \param hTWD - TWD module object handle
* \return None
*
* \par Description
* Close all BA receiver sessions and pass all packets in the TID queue to upper layer.
*
* \sa
*/
void TWD_CloseAllBaSessions(TI_HANDLE hTWD);
/** @ingroup BSS
* \brief Set FW HT Capabilities
*
* \param hTWD - TWD module object handle
* \param pHtCapabilitiesIe - Pointer to string of HT capability IE unparsed
* \param bAllowHtOperation - TI_TRUE: HT operation allowed, Otherwise: HT operation NOT allowed
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Parse HT capability IE and set the current AP HT Capabilities to the FW
*
* \sa
*/
TI_STATUS TWD_CfgSetFwHtCapabilities (TI_HANDLE hTWD,
Tdot11HtCapabilitiesUnparse *pHtCapabilitiesIe,
TI_BOOL bAllowHtOperation);
/** @ingroup BSS
* \brief Set FW HT Information
*
* \param hTWD - TWD module object handle
* \param pHtInformationIe - Pointer to string of HT information IE unparsed
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Parse HT Information IE and set the current AP HT Information to the FW
*
* \sa
*/
TI_STATUS TWD_CfgSetFwHtInformation (TI_HANDLE hTWD, Tdot11HtInformationUnparse *pHtInformationIe);
/** @ingroup UnKnown
* \brief Enable/Disabel burst mode
*
* \param hTWD - TWD module object handle
* \param bEnabled - burst mode: Enable/Disable
* \return TI_OK
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_CfgBurstMode (TI_HANDLE hTWD, TI_BOOL bEnabled);
/*-------------*/
/* Interrogate */
/*-------------*/
/** @ingroup UnKnown
* \brief Interrogate Roamming Statistics
*
* \param hTWD - TWD module object handle
* \param fCb - Pointer to Command CB Function
* \param hCb - Handle to Command CB Function Obj Parameters
* \param pCb - Pointer to read parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Interrogate ACX Roamming Statistics
*
* \sa
*/
TI_STATUS TWD_ItrRoammingStatisitics (TI_HANDLE hTWD, void *fCb, TI_HANDLE hCb, void *pCb);
/** @ingroup UnKnown
* \brief Configure/Interrogate RSSI
*
* \param hTWD - TWD module object handle
* \param fCb - Pointer to Command CB Function
* \param hCb - Handle to Command CB Function Obj Parameters
* \param pCb - Pointer to read parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Configure/Interrogate StationId information element to/from FW
* This information element specifies the MAC Address assigned to the STATION or AP.
* The RSSI is Configed to default value which is the permanent MAC address which
* is stored in the adaptor's non-volatile memory.
*
* \sa
*/
TI_STATUS TWD_ItrRSSI (TI_HANDLE hTWD, void *fCb, TI_HANDLE hCb, void *pCb);
/** @ingroup UnKnown
* \brief Interrogate Memory Map
*
* \param hTWD - TWD module object handle
* \param pMap - Pointer to Output Memory Map
* \param fCb - Pointer to Callback Function
* \param hCb - Handle to Callback Function Parameters Object
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* Interrogate Memory Map from FW
*
* \sa MemoryMap_t
*/TI_STATUS TWD_ItrMemoryMap (TI_HANDLE hTWD, MemoryMap_t *pMap, void *fCb, TI_HANDLE hCb);
/** @ingroup UnKnown
* \brief Interrogate Statistics
*
* \param hTWD - TWD module object handle
* \param fCb - Pointer to Command CB Function
* \param hCb - Handle to Command CB Function Obj Parameters
* \param pCb - Pointer to read parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/
TI_STATUS TWD_ItrStatistics (TI_HANDLE hTWD, void *fCb, TI_HANDLE hCb, void *pCb);
/** @ingroup Data_Path
* \brief Interrogate Data Filter Statistics
*
* \param hTWD - TWD module object handle
* \param fCb - Pointer to Command CB Function
* \param hCb - Handle to Command CB Function Obj Parameters
* \param pCb - Pointer to read parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
*
* \sa
*/TI_STATUS TWD_ItrDataFilterStatistics (TI_HANDLE hTWD, void *fCb, TI_HANDLE hCb, void *pCb);
/*
* --------------------------------------------------------------
* TNETW-Driver Tx API Functions
* --------------------------------------------------------------
*/
/** @ingroup Data_Path
* \brief TWD TX Control Block Allocation
*
* \param hTWD - TWD module object handle
* \return Pointer to Control Block Entry on success or NULL on failure
*
* \par Description
* Use this function for Allocate a Control-Block for the packet Tx parameters and descriptor
*
* \sa
*/
TTxCtrlBlk *TWD_txCtrlBlk_Alloc (TI_HANDLE hTWD);
/** @ingroup Data_Path
* \brief TWD TX Control Block Free
*
* \param hTWD - TWD module object handle
* \param pCurrentEntry - Pointer to TX Control Block Entry to Free
* \return void
*
* \par Description
* Use this function for Free a Control-Block of packet Tx parameters and descriptor
*
* \sa
*/
void TWD_txCtrlBlk_Free (TI_HANDLE hTWD, TTxCtrlBlk *pCurrentEntry);
/** @ingroup Data_Path
* \brief TWD TX Control Get Pointer
*
* \param hTWD - TWD module object handle
* \param descId - Id of TX Control Block Descriptor
* \return Pointer to Control Block Entry on success or NULL on failure
*
* \par Description
* Use this function for Get a Pointer to a Control-Block of packet Tx parameters and descriptor
*
* \sa
*/
TTxCtrlBlk *TWD_txCtrlBlk_GetPointer (TI_HANDLE hTWD, TI_UINT8 descId);
/** @ingroup Data_Path
* \brief Allocate Resources for TX HW Queue
*
* \param hTWD - TWD module object handle
* \param pTxCtrlBlk - The Tx packet control block
* \return see - ETxHwQueStatus
*
* \par Description
* Allocates Resources (HW-blocks number required) for TX HW Queue
*
* \sa
*/
ETxHwQueStatus TWD_txHwQueue_AllocResources (TI_HANDLE hTWD, TTxCtrlBlk *pTxCtrlBlk);
/** @ingroup Data_Path
* \brief TX Xfer Send Packet
*
* \param hTWD - TWD module object handle
* \param pPktCtrlBlk - Pointer to TX Control Block Entry to Free
* \return see ETxnStatus
*
* \par Description
* Send Packet via TX Xfer
*
* \sa
*/
ETxnStatus TWD_txXfer_SendPacket (TI_HANDLE hTWD, TTxCtrlBlk *pPktCtrlBlk);
/** @ingroup Control
* \brief Watch Dog Expire Event
*
* \param hTWD - TWD module object handle
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* This function handles the Event of Watch Dog Expire (FW stopped)
*
* \sa
*/
TI_STATUS TWD_WdExpireEvent (TI_HANDLE hTWD);
/*
* --------------------------------------------------------------
* BIT API Functions
* --------------------------------------------------------------
*/
/** @ingroup Control
* \brief TWD Test Command Complete CB
*
* \param Handle - handle to object
* \param eStatus - Status of Driver Test Performed
* \param pTestCmdParams - Pointer to Output of Test Command Parameters
* \return void
*
* \par Description
* The function prototype for the BIT Test Command Complete CB
* Enables user to implement and use its own BIT Test Command Complete CB
* which will be called when Driver Test end
*
* \sa TWDriverTest
*/
typedef void (*TTestCmdCB)(TI_HANDLE Handle,
TI_STATUS eStatus,
TI_HANDLE pTestCmdParams);
/** @ingroup Control
* \brief TWD Test Command Complete CB
*
* \param Handle - handle to object
* \param eStatus - Status of Driver Test Performed (Complete/Pending/Error)
* \param pTestCmdParams - Pointer to Output of Test Command Parameters
* \return void
*
* \par Description
* The function implementation for the BIT Test Command Complete CB
*
* \sa
*/
void TWDriverTestCB(TI_HANDLE Handle,
TI_STATUS eStatus,
TI_HANDLE pTestCmdParams);
/** @ingroup Control
* \brief TWD Driver Test
*
* \param hTWD - handle to TWD object
* \param eTestCmd - Identifier of test Command to Perform
* \param pTestCmdParams - Pointer to Input/Output Test Command Parameters
* \param fCb - Test Command Complete CB
* \param hCb - Handle to Test Command Complete CB Parameters
* \return TI_OK on success or TI_NOK on failure
*
* \par Description
* The implementation of the BIT Test Command
*
* \sa
*/
TI_STATUS TWDriverTest(TI_HANDLE hTWD,
TestCmdID_enum eTestCmd,
void* pTestCmdParams,
TTestCmdCB fCb,
TI_HANDLE hCb);
/**
* \brief TWD get FEM type
* *
* \param Handle - handle to object
* \return uint8
*
* \par Description
* The function return the Front end module that was read frm FW register *
* \sa
*/
TI_UINT8 TWD_GetFEMType (TI_HANDLE hTWD);
/**
* \brief TWD end function of read radio state machine
* * *
* \param Handle - handle to object
* \return void
*
* \par Description
* The function calling to HwInit call back function, after finish reading FEM registers *
* \sa
*/
void TWD_FinalizeFEMRead(TI_HANDLE hTWD);
void TWD_FinalizePolarityRead(TI_HANDLE hTWD);
/** @ingroup Data_Path
* \brief TWD_CfgBurstMode
*
* \param hTWD - TWD module object handle
* \param bEnabled - is Burst mode enabled
* \return TI_OK
*
* \par Description
* Use this function to enable/disbale the burst mode
*
* \sa
*/
TI_STATUS TWD_CfgBurstMode (TI_HANDLE hTWD, TI_BOOL bEnabled);
TI_STATUS TWD_SetRateMngDebug(TI_HANDLE hTWD, RateMangeParams_t *pRateMngParams);
TI_STATUS TWD_GetRateMngDebug(TI_HANDLE hTWD, RateMangeReadParams_t *pParamInfo);
#endif /* TWDRIVER_H */