/** @file
TIS (TPM Interface Specification) functions used by TPM1.2.
Copyright (c) 2013 - 2015, Intel Corporation. All rights reserved.<BR>
(C) Copyright 2015 Hewlett Packard Enterprise Development LP<BR>
This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
http://opensource.org/licenses/bsd-license.php
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
**/
#include <Uefi.h>
#include <IndustryStandard/Tpm12.h>
#include <Library/BaseLib.h>
#include <Library/BaseMemoryLib.h>
#include <Library/IoLib.h>
#include <Library/TimerLib.h>
#include <Library/DebugLib.h>
#include <Library/Tpm12CommandLib.h>
#include <Library/PcdLib.h>
//
// Set structure alignment to 1-byte
//
#pragma pack (1)
//
// Register set map as specified in TIS specification Chapter 10
//
typedef struct {
///
/// Used to gain ownership for this particular port.
///
UINT8 Access; // 0
UINT8 Reserved1[7]; // 1
///
/// Controls interrupts.
///
UINT32 IntEnable; // 8
///
/// SIRQ vector to be used by the TPM.
///
UINT8 IntVector; // 0ch
UINT8 Reserved2[3]; // 0dh
///
/// What caused interrupt.
///
UINT32 IntSts; // 10h
///
/// Shows which interrupts are supported by that particular TPM.
///
UINT32 IntfCapability; // 14h
///
/// Status Register. Provides status of the TPM.
///
UINT8 Status; // 18h
///
/// Number of consecutive writes that can be done to the TPM.
///
UINT16 BurstCount; // 19h
UINT8 Reserved3[9];
///
/// Read or write FIFO, depending on transaction.
///
UINT32 DataFifo; // 24h
UINT8 Reserved4[0xed8]; // 28h
///
/// Vendor ID
///
UINT16 Vid; // 0f00h
///
/// Device ID
///
UINT16 Did; // 0f02h
///
/// Revision ID
///
UINT8 Rid; // 0f04h
///
/// TCG defined configuration registers.
///
UINT8 TcgDefined[0x7b]; // 0f05h
///
/// Alias to I/O legacy space.
///
UINT32 LegacyAddress1; // 0f80h
///
/// Additional 8 bits for I/O legacy space extension.
///
UINT32 LegacyAddress1Ex; // 0f84h
///
/// Alias to second I/O legacy space.
///
UINT32 LegacyAddress2; // 0f88h
///
/// Additional 8 bits for second I/O legacy space extension.
///
UINT32 LegacyAddress2Ex; // 0f8ch
///
/// Vendor-defined configuration registers.
///
UINT8 VendorDefined[0x70];// 0f90h
} TIS_PC_REGISTERS;
//
// Restore original structure alignment
//
#pragma pack ()
//
// Define pointer types used to access TIS registers on PC
//
typedef TIS_PC_REGISTERS *TIS_PC_REGISTERS_PTR;
//
// Define bits of ACCESS and STATUS registers
//
///
/// This bit is a 1 to indicate that the other bits in this register are valid.
///
#define TIS_PC_VALID BIT7
///
/// Indicate that this locality is active.
///
#define TIS_PC_ACC_ACTIVE BIT5
///
/// Set to 1 to indicate that this locality had the TPM taken away while
/// this locality had the TIS_PC_ACC_ACTIVE bit set.
///
#define TIS_PC_ACC_SEIZED BIT4
///
/// Set to 1 to indicate that TPM MUST reset the
/// TIS_PC_ACC_ACTIVE bit and remove ownership for localities less than the
/// locality that is writing this bit.
///
#define TIS_PC_ACC_SEIZE BIT3
///
/// When this bit is 1, another locality is requesting usage of the TPM.
///
#define TIS_PC_ACC_PENDIND BIT2
///
/// Set to 1 to indicate that this locality is requesting to use TPM.
///
#define TIS_PC_ACC_RQUUSE BIT1
///
/// A value of 1 indicates that a T/OS has not been established on the platform
///
#define TIS_PC_ACC_ESTABLISH BIT0
///
/// When this bit is 1, TPM is in the Ready state,
/// indicating it is ready to receive a new command.
///
#define TIS_PC_STS_READY BIT6
///
/// Write a 1 to this bit to cause the TPM to execute that command.
///
#define TIS_PC_STS_GO BIT5
///
/// This bit indicates that the TPM has data available as a response.
///
#define TIS_PC_STS_DATA BIT4
///
/// The TPM sets this bit to a value of 1 when it expects another byte of data for a command.
///
#define TIS_PC_STS_EXPECT BIT3
///
/// Writes a 1 to this bit to force the TPM to re-send the response.
///
#define TIS_PC_STS_RETRY BIT1
//
// Default TimeOut value
//
#define TIS_TIMEOUT_A (750 * 1000) // 750ms
#define TIS_TIMEOUT_B (2000 * 1000) // 2s
#define TIS_TIMEOUT_C (750 * 1000) // 750ms
#define TIS_TIMEOUT_D (750 * 1000) // 750ms
//
// Max TPM command/reponse length
//
#define TPMCMDBUFLENGTH 1024
/**
Check whether TPM chip exist.
@param[in] TisReg Pointer to TIS register.
@retval TRUE TPM chip exists.
@retval FALSE TPM chip is not found.
**/
BOOLEAN
Tpm12TisPcPresenceCheck (
IN TIS_PC_REGISTERS_PTR TisReg
)
{
UINT8 RegRead;
RegRead = MmioRead8 ((UINTN)&TisReg->Access);
return (BOOLEAN)(RegRead != (UINT8)-1);
}
/**
Check whether the value of a TPM chip register satisfies the input BIT setting.
@param[in] Register Address port of register to be checked.
@param[in] BitSet Check these data bits are set.
@param[in] BitClear Check these data bits are clear.
@param[in] TimeOut The max wait time (unit MicroSecond) when checking register.
@retval EFI_SUCCESS The register satisfies the check bit.
@retval EFI_TIMEOUT The register can't run into the expected status in time.
**/
EFI_STATUS
Tpm12TisPcWaitRegisterBits (
IN UINT8 *Register,
IN UINT8 BitSet,
IN UINT8 BitClear,
IN UINT32 TimeOut
)
{
UINT8 RegRead;
UINT32 WaitTime;
for (WaitTime = 0; WaitTime < TimeOut; WaitTime += 30){
RegRead = MmioRead8 ((UINTN)Register);
if ((RegRead & BitSet) == BitSet && (RegRead & BitClear) == 0)
return EFI_SUCCESS;
MicroSecondDelay (30);
}
return EFI_TIMEOUT;
}
/**
Get BurstCount by reading the burstCount field of a TIS regiger
in the time of default TIS_TIMEOUT_D.
@param[in] TisReg Pointer to TIS register.
@param[out] BurstCount Pointer to a buffer to store the got BurstConut.
@retval EFI_SUCCESS Get BurstCount.
@retval EFI_INVALID_PARAMETER TisReg is NULL or BurstCount is NULL.
@retval EFI_TIMEOUT BurstCount can't be got in time.
**/
EFI_STATUS
Tpm12TisPcReadBurstCount (
IN TIS_PC_REGISTERS_PTR TisReg,
OUT UINT16 *BurstCount
)
{
UINT32 WaitTime;
UINT8 DataByte0;
UINT8 DataByte1;
if (BurstCount == NULL || TisReg == NULL) {
return EFI_INVALID_PARAMETER;
}
WaitTime = 0;
do {
//
// TIS_PC_REGISTERS_PTR->burstCount is UINT16, but it is not 2bytes aligned,
// so it needs to use MmioRead8 to read two times
//
DataByte0 = MmioRead8 ((UINTN)&TisReg->BurstCount);
DataByte1 = MmioRead8 ((UINTN)&TisReg->BurstCount + 1);
*BurstCount = (UINT16)((DataByte1 << 8) + DataByte0);
if (*BurstCount != 0) {
return EFI_SUCCESS;
}
MicroSecondDelay (30);
WaitTime += 30;
} while (WaitTime < TIS_TIMEOUT_D);
return EFI_TIMEOUT;
}
/**
Set TPM chip to ready state by sending ready command TIS_PC_STS_READY
to Status Register in time.
@param[in] TisReg Pointer to TIS register.
@retval EFI_SUCCESS TPM chip enters into ready state.
@retval EFI_INVALID_PARAMETER TisReg is NULL.
@retval EFI_TIMEOUT TPM chip can't be set to ready state in time.
**/
EFI_STATUS
Tpm12TisPcPrepareCommand (
IN TIS_PC_REGISTERS_PTR TisReg
)
{
EFI_STATUS Status;
if (TisReg == NULL) {
return EFI_INVALID_PARAMETER;
}
MmioWrite8((UINTN)&TisReg->Status, TIS_PC_STS_READY);
Status = Tpm12TisPcWaitRegisterBits (
&TisReg->Status,
TIS_PC_STS_READY,
0,
TIS_TIMEOUT_B
);
return Status;
}
/**
Get the control of TPM chip by sending requestUse command TIS_PC_ACC_RQUUSE
to ACCESS Register in the time of default TIS_TIMEOUT_A.
@param[in] TisReg Pointer to TIS register.
@retval EFI_SUCCESS Get the control of TPM chip.
@retval EFI_INVALID_PARAMETER TisReg is NULL.
@retval EFI_NOT_FOUND TPM chip doesn't exit.
@retval EFI_TIMEOUT Can't get the TPM control in time.
**/
EFI_STATUS
Tpm12TisPcRequestUseTpm (
IN TIS_PC_REGISTERS_PTR TisReg
)
{
EFI_STATUS Status;
if (TisReg == NULL) {
return EFI_INVALID_PARAMETER;
}
if (!Tpm12TisPcPresenceCheck (TisReg)) {
return EFI_NOT_FOUND;
}
MmioWrite8((UINTN)&TisReg->Access, TIS_PC_ACC_RQUUSE);
Status = Tpm12TisPcWaitRegisterBits (
&TisReg->Access,
(UINT8)(TIS_PC_ACC_ACTIVE |TIS_PC_VALID),
0,
TIS_TIMEOUT_A
);
return Status;
}
/**
Send a command to TPM for execution and return response data.
@param[in] TisReg TPM register space base address.
@param[in] BufferIn Buffer for command data.
@param[in] SizeIn Size of command data.
@param[in, out] BufferOut Buffer for response data.
@param[in, out] SizeOut Size of response data.
@retval EFI_SUCCESS Operation completed successfully.
@retval EFI_BUFFER_TOO_SMALL Response data buffer is too small.
@retval EFI_DEVICE_ERROR Unexpected device behavior.
@retval EFI_UNSUPPORTED Unsupported TPM version
**/
EFI_STATUS
Tpm12TisTpmCommand (
IN TIS_PC_REGISTERS_PTR TisReg,
IN UINT8 *BufferIn,
IN UINT32 SizeIn,
IN OUT UINT8 *BufferOut,
IN OUT UINT32 *SizeOut
)
{
EFI_STATUS Status;
UINT16 BurstCount;
UINT32 Index;
UINT32 TpmOutSize;
UINT16 Data16;
UINT32 Data32;
DEBUG_CODE (
UINTN DebugSize;
DEBUG ((EFI_D_VERBOSE, "Tpm12TisTpmCommand Send - "));
if (SizeIn > 0x100) {
DebugSize = 0x40;
} else {
DebugSize = SizeIn;
}
for (Index = 0; Index < DebugSize; Index++) {
DEBUG ((EFI_D_VERBOSE, "%02x ", BufferIn[Index]));
}
if (DebugSize != SizeIn) {
DEBUG ((EFI_D_VERBOSE, "...... "));
for (Index = SizeIn - 0x20; Index < SizeIn; Index++) {
DEBUG ((EFI_D_VERBOSE, "%02x ", BufferIn[Index]));
}
}
DEBUG ((EFI_D_VERBOSE, "\n"));
);
TpmOutSize = 0;
Status = Tpm12TisPcPrepareCommand (TisReg);
if (EFI_ERROR (Status)){
DEBUG ((DEBUG_ERROR, "Tpm12 is not ready for command!\n"));
return EFI_DEVICE_ERROR;
}
//
// Send the command data to Tpm
//
Index = 0;
while (Index < SizeIn) {
Status = Tpm12TisPcReadBurstCount (TisReg, &BurstCount);
if (EFI_ERROR (Status)) {
Status = EFI_DEVICE_ERROR;
goto Exit;
}
for (; BurstCount > 0 && Index < SizeIn; BurstCount--) {
MmioWrite8((UINTN)&TisReg->DataFifo, *(BufferIn + Index));
Index++;
}
}
//
// Check the Tpm status STS_EXPECT change from 1 to 0
//
Status = Tpm12TisPcWaitRegisterBits (
&TisReg->Status,
(UINT8) TIS_PC_VALID,
TIS_PC_STS_EXPECT,
TIS_TIMEOUT_C
);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "Tpm12 The send buffer too small!\n"));
Status = EFI_BUFFER_TOO_SMALL;
goto Exit;
}
//
// Executed the TPM command and waiting for the response data ready
//
MmioWrite8((UINTN)&TisReg->Status, TIS_PC_STS_GO);
Status = Tpm12TisPcWaitRegisterBits (
&TisReg->Status,
(UINT8) (TIS_PC_VALID | TIS_PC_STS_DATA),
0,
TIS_TIMEOUT_B
);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "Wait for Tpm12 response data time out!!\n"));
Status = EFI_DEVICE_ERROR;
goto Exit;
}
//
// Get response data header
//
Index = 0;
BurstCount = 0;
while (Index < sizeof (TPM_RSP_COMMAND_HDR)) {
Status = Tpm12TisPcReadBurstCount (TisReg, &BurstCount);
if (EFI_ERROR (Status)) {
Status = EFI_DEVICE_ERROR;
goto Exit;
}
for (; BurstCount > 0; BurstCount--) {
*(BufferOut + Index) = MmioRead8 ((UINTN)&TisReg->DataFifo);
Index++;
if (Index == sizeof (TPM_RSP_COMMAND_HDR)) break;
}
}
DEBUG_CODE (
DEBUG ((EFI_D_VERBOSE, "Tpm12TisTpmCommand ReceiveHeader - "));
for (Index = 0; Index < sizeof (TPM_RSP_COMMAND_HDR); Index++) {
DEBUG ((EFI_D_VERBOSE, "%02x ", BufferOut[Index]));
}
DEBUG ((EFI_D_VERBOSE, "\n"));
);
//
// Check the reponse data header (tag,parasize and returncode )
//
CopyMem (&Data16, BufferOut, sizeof (UINT16));
if (SwapBytes16 (Data16) != TPM_TAG_RSP_COMMAND) {
DEBUG ((EFI_D_ERROR, "TPM12: TPM_ST_RSP error - %x\n", TPM_TAG_RSP_COMMAND));
Status = EFI_UNSUPPORTED;
goto Exit;
}
CopyMem (&Data32, (BufferOut + 2), sizeof (UINT32));
TpmOutSize = SwapBytes32 (Data32);
if (*SizeOut < TpmOutSize) {
Status = EFI_BUFFER_TOO_SMALL;
goto Exit;
}
*SizeOut = TpmOutSize;
//
// Continue reading the remaining data
//
while ( Index < TpmOutSize ) {
for (; BurstCount > 0; BurstCount--) {
*(BufferOut + Index) = MmioRead8 ((UINTN)&TisReg->DataFifo);
Index++;
if (Index == TpmOutSize) {
Status = EFI_SUCCESS;
goto Exit;
}
}
Status = Tpm12TisPcReadBurstCount (TisReg, &BurstCount);
if (EFI_ERROR (Status)) {
Status = EFI_DEVICE_ERROR;
goto Exit;
}
}
Exit:
DEBUG_CODE (
DEBUG ((EFI_D_VERBOSE, "Tpm12TisTpmCommand Receive - "));
for (Index = 0; Index < TpmOutSize; Index++) {
DEBUG ((EFI_D_VERBOSE, "%02x ", BufferOut[Index]));
}
DEBUG ((EFI_D_VERBOSE, "\n"));
);
MmioWrite8((UINTN)&TisReg->Status, TIS_PC_STS_READY);
return Status;
}
/**
This service enables the sending of commands to the TPM12.
@param[in] InputParameterBlockSize Size of the TPM12 input parameter block.
@param[in] InputParameterBlock Pointer to the TPM12 input parameter block.
@param[in,out] OutputParameterBlockSize Size of the TPM12 output parameter block.
@param[in] OutputParameterBlock Pointer to the TPM12 output parameter block.
@retval EFI_SUCCESS The command byte stream was successfully sent to the device and a response was successfully received.
@retval EFI_DEVICE_ERROR The command was not successfully sent to the device or a response was not successfully received from the device.
@retval EFI_BUFFER_TOO_SMALL The output parameter block is too small.
**/
EFI_STATUS
EFIAPI
Tpm12SubmitCommand (
IN UINT32 InputParameterBlockSize,
IN UINT8 *InputParameterBlock,
IN OUT UINT32 *OutputParameterBlockSize,
IN UINT8 *OutputParameterBlock
)
{
return Tpm12TisTpmCommand (
(TIS_PC_REGISTERS_PTR) (UINTN) PcdGet64 (PcdTpmBaseAddress),
InputParameterBlock,
InputParameterBlockSize,
OutputParameterBlock,
OutputParameterBlockSize
);
}
/**
This service requests use TPM12.
@retval EFI_SUCCESS Get the control of TPM12 chip.
@retval EFI_NOT_FOUND TPM12 not found.
@retval EFI_DEVICE_ERROR Unexpected device behavior.
**/
EFI_STATUS
EFIAPI
Tpm12RequestUseTpm (
VOID
)
{
return Tpm12TisPcRequestUseTpm ((TIS_PC_REGISTERS_PTR) (UINTN) PcdGet64 (PcdTpmBaseAddress));
}