/* * arch/arm/mach-pxa/include/mach/pcm027.h * * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de> * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ /* * Definitions of CPU card resources only */ /* phyCORE-PXA270 (PCM027) Interrupts */ #define PCM027_IRQ(x) (IRQ_BOARD_START + (x)) #define PCM027_BTDET_IRQ PCM027_IRQ(0) #define PCM027_FF_RI_IRQ PCM027_IRQ(1) #define PCM027_MMCDET_IRQ PCM027_IRQ(2) #define PCM027_PM_5V_IRQ PCM027_IRQ(3) #define PCM027_NR_IRQS (IRQ_BOARD_START + 32) /* I2C RTC */ #define PCM027_RTC_IRQ_GPIO 0 #define PCM027_RTC_IRQ IRQ_GPIO(PCM027_RTC_IRQ_GPIO) #define PCM027_RTC_IRQ_EDGE IRQ_TYPE_EDGE_FALLING #define ADR_PCM027_RTC 0x51 /* I2C address */ /* I2C EEPROM */ #define ADR_PCM027_EEPROM 0x54 /* I2C address */ /* Ethernet chip (SMSC91C111) */ #define PCM027_ETH_IRQ_GPIO 52 #define PCM027_ETH_IRQ IRQ_GPIO(PCM027_ETH_IRQ_GPIO) #define PCM027_ETH_IRQ_EDGE IRQ_TYPE_EDGE_RISING #define PCM027_ETH_PHYS PXA_CS5_PHYS #define PCM027_ETH_SIZE (1*1024*1024) /* CAN controller SJA1000 (unsupported yet) */ #define PCM027_CAN_IRQ_GPIO 114 #define PCM027_CAN_IRQ IRQ_GPIO(PCM027_CAN_IRQ_GPIO) #define PCM027_CAN_IRQ_EDGE IRQ_TYPE_EDGE_FALLING #define PCM027_CAN_PHYS 0x22000000 #define PCM027_CAN_SIZE 0x100 /* SPI GPIO expander (unsupported yet) */ #define PCM027_EGPIO_IRQ_GPIO 27 #define PCM027_EGPIO_IRQ IRQ_GPIO(PCM027_EGPIO_IRQ_GPIO) #define PCM027_EGPIO_IRQ_EDGE IRQ_TYPE_EDGE_FALLING #define PCM027_EGPIO_CS 24 /* * TODO: Switch this pin from dedicated usage to GPIO if * more than the MAX7301 device is connected to this SPI bus */ #define PCM027_EGPIO_CS_MODE GPIO24_SFRM_MD /* Flash memory */ #define PCM027_FLASH_PHYS 0x00000000 #define PCM027_FLASH_SIZE 0x02000000 /* onboard LEDs connected to GPIO */ #define PCM027_LED_CPU 90 #define PCM027_LED_HEARD_BEAT 91 /* * This CPU module needs a baseboard to work. After basic initializing * its own devices, it calls baseboard's init function. * TODO: Add your own basebaord init function and call it from * inside pcm027_init(). This example here is for the developmen board. * Refer pcm990-baseboard.c */ extern void pcm990_baseboard_init(void);