/*
* sound/oss/sb_common.c
*
* Common routines for Sound Blaster compatible cards.
*
*
* Copyright (C) by Hannu Savolainen 1993-1997
*
* OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL)
* Version 2 (June 1991). See the "COPYING" file distributed with this software
* for more info.
*
*
* Daniel J. Rodriksson: Modified sbintr to handle 8 and 16 bit interrupts
* for full duplex support ( only sb16 by now )
* Rolf Fokkens: Added (BETA?) support for ES1887 chips.
* (fokkensr@vertis.nl) Which means: You can adjust the recording levels.
*
* 2000/01/18 - separated sb_card and sb_common -
* Jeff Garzik <jgarzik@pobox.com>
*
* 2000/09/18 - got rid of attach_uart401
* Arnaldo Carvalho de Melo <acme@conectiva.com.br>
*
* 2001/01/26 - replaced CLI/STI with spinlocks
* Chris Rankin <rankinc@zipworld.com.au>
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/spinlock.h>
#include <linux/slab.h>
#include "sound_config.h"
#include "sound_firmware.h"
#include "mpu401.h"
#include "sb_mixer.h"
#include "sb.h"
#include "sb_ess.h"
/*
* global module flag
*/
int sb_be_quiet;
static sb_devc *detected_devc; /* For communication from probe to init */
static sb_devc *last_devc; /* For MPU401 initialization */
static unsigned char jazz_irq_bits[] = {
0, 0, 2, 3, 0, 1, 0, 4, 0, 2, 5, 0, 0, 0, 0, 6
};
static unsigned char jazz_dma_bits[] = {
0, 1, 0, 2, 0, 3, 0, 4
};
void *smw_free;
/*
* Jazz16 chipset specific control variables
*/
static int jazz16_base; /* Not detected */
static unsigned char jazz16_bits; /* I/O relocation bits */
static DEFINE_SPINLOCK(jazz16_lock);
/*
* Logitech Soundman Wave specific initialization code
*/
#ifdef SMW_MIDI0001_INCLUDED
#include "smw-midi0001.h"
#else
static unsigned char *smw_ucode;
static int smw_ucodeLen;
#endif
static sb_devc *last_sb; /* Last sb loaded */
int sb_dsp_command(sb_devc * devc, unsigned char val)
{
int i;
unsigned long limit;
limit = jiffies + HZ / 10; /* Timeout */
/*
* Note! the i<500000 is an emergency exit. The sb_dsp_command() is sometimes
* called while interrupts are disabled. This means that the timer is
* disabled also. However the timeout situation is a abnormal condition.
* Normally the DSP should be ready to accept commands after just couple of
* loops.
*/
for (i = 0; i < 500000 && (limit-jiffies)>0; i++)
{
if ((inb(DSP_STATUS) & 0x80) == 0)
{
outb((val), DSP_COMMAND);
return 1;
}
}
printk(KERN_WARNING "Sound Blaster: DSP command(%x) timeout.\n", val);
return 0;
}
int sb_dsp_get_byte(sb_devc * devc)
{
int i;
for (i = 1000; i; i--)
{
if (inb(DSP_DATA_AVAIL) & 0x80)
return inb(DSP_READ);
}
return 0xffff;
}
static void sb_intr (sb_devc *devc)
{
int status;
unsigned char src = 0xff;
if (devc->model == MDL_SB16)
{
src = sb_getmixer(devc, IRQ_STAT); /* Interrupt source register */
if (src & 4) /* MPU401 interrupt */
if(devc->midi_irq_cookie)
uart401intr(devc->irq, devc->midi_irq_cookie);
if (!(src & 3))
return; /* Not a DSP interrupt */
}
if (devc->intr_active && (!devc->fullduplex || (src & 0x01)))
{
switch (devc->irq_mode)
{
case IMODE_OUTPUT:
DMAbuf_outputintr(devc->dev, 1);
break;
case IMODE_INPUT:
DMAbuf_inputintr(devc->dev);
break;
case IMODE_INIT:
break;
case IMODE_MIDI:
sb_midi_interrupt(devc);
break;
default:
/* printk(KERN_WARNING "Sound Blaster: Unexpected interrupt\n"); */
;
}
}
else if (devc->intr_active_16 && (src & 0x02))
{
switch (devc->irq_mode_16)
{
case IMODE_OUTPUT:
DMAbuf_outputintr(devc->dev, 1);
break;
case IMODE_INPUT:
DMAbuf_inputintr(devc->dev);
break;
case IMODE_INIT:
break;
default:
/* printk(KERN_WARNING "Sound Blaster: Unexpected interrupt\n"); */
;
}
}
/*
* Acknowledge interrupts
*/
if (src & 0x01)
status = inb(DSP_DATA_AVAIL);
if (devc->model == MDL_SB16 && src & 0x02)
status = inb(DSP_DATA_AVL16);
}
static void pci_intr(sb_devc *devc)
{
int src = inb(devc->pcibase+0x1A);
src&=3;
if(src)
sb_intr(devc);
}
static irqreturn_t sbintr(int irq, void *dev_id)
{
sb_devc *devc = dev_id;
devc->irq_ok = 1;
switch (devc->model) {
case MDL_ESSPCI:
pci_intr (devc);
break;
case MDL_ESS:
ess_intr (devc);
break;
default:
sb_intr (devc);
break;
}
return IRQ_HANDLED;
}
int sb_dsp_reset(sb_devc * devc)
{
int loopc;
DEB(printk("Entered sb_dsp_reset()\n"));
if (devc->model == MDL_ESS) return ess_dsp_reset (devc);
/* This is only for non-ESS chips */
outb(1, DSP_RESET);
udelay(10);
outb(0, DSP_RESET);
udelay(30);
for (loopc = 0; loopc < 1000 && !(inb(DSP_DATA_AVAIL) & 0x80); loopc++);
if (inb(DSP_READ) != 0xAA)
{
DDB(printk("sb: No response to RESET\n"));
return 0; /* Sorry */
}
DEB(printk("sb_dsp_reset() OK\n"));
return 1;
}
static void dsp_get_vers(sb_devc * devc)
{
int i;
unsigned long flags;
DDB(printk("Entered dsp_get_vers()\n"));
spin_lock_irqsave(&devc->lock, flags);
devc->major = devc->minor = 0;
sb_dsp_command(devc, 0xe1); /* Get version */
for (i = 100000; i; i--)
{
if (inb(DSP_DATA_AVAIL) & 0x80)
{
if (devc->major == 0)
devc->major = inb(DSP_READ);
else
{
devc->minor = inb(DSP_READ);
break;
}
}
}
spin_unlock_irqrestore(&devc->lock, flags);
DDB(printk("DSP version %d.%02d\n", devc->major, devc->minor));
}
static int sb16_set_dma_hw(sb_devc * devc)
{
int bits;
if (devc->dma8 != 0 && devc->dma8 != 1 && devc->dma8 != 3)
{
printk(KERN_ERR "SB16: Invalid 8 bit DMA (%d)\n", devc->dma8);
return 0;
}
bits = (1 << devc->dma8);
if (devc->dma16 >= 5 && devc->dma16 <= 7)
bits |= (1 << devc->dma16);
sb_setmixer(devc, DMA_NR, bits);
return 1;
}
static void sb16_set_mpu_port(sb_devc * devc, struct address_info *hw_config)
{
/*
* This routine initializes new MIDI port setup register of SB Vibra (CT2502).
*/
unsigned char bits = sb_getmixer(devc, 0x84) & ~0x06;
switch (hw_config->io_base)
{
case 0x300:
sb_setmixer(devc, 0x84, bits | 0x04);
break;
case 0x330:
sb_setmixer(devc, 0x84, bits | 0x00);
break;
default:
sb_setmixer(devc, 0x84, bits | 0x02); /* Disable MPU */
printk(KERN_ERR "SB16: Invalid MIDI I/O port %x\n", hw_config->io_base);
}
}
static int sb16_set_irq_hw(sb_devc * devc, int level)
{
int ival;
switch (level)
{
case 5:
ival = 2;
break;
case 7:
ival = 4;
break;
case 9:
ival = 1;
break;
case 10:
ival = 8;
break;
default:
printk(KERN_ERR "SB16: Invalid IRQ%d\n", level);
return 0;
}
sb_setmixer(devc, IRQ_NR, ival);
return 1;
}
static void relocate_Jazz16(sb_devc * devc, struct address_info *hw_config)
{
unsigned char bits = 0;
unsigned long flags;
if (jazz16_base != 0 && jazz16_base != hw_config->io_base)
return;
switch (hw_config->io_base)
{
case 0x220:
bits = 1;
break;
case 0x240:
bits = 2;
break;
case 0x260:
bits = 3;
break;
default:
return;
}
bits = jazz16_bits = bits << 5;
jazz16_base = hw_config->io_base;
/*
* Magic wake up sequence by writing to 0x201 (aka Joystick port)
*/
spin_lock_irqsave(&jazz16_lock, flags);
outb((0xAF), 0x201);
outb((0x50), 0x201);
outb((bits), 0x201);
spin_unlock_irqrestore(&jazz16_lock, flags);
}
static int init_Jazz16(sb_devc * devc, struct address_info *hw_config)
{
char name[100];
/*
* First try to check that the card has Jazz16 chip. It identifies itself
* by returning 0x12 as response to DSP command 0xfa.
*/
if (!sb_dsp_command(devc, 0xfa))
return 0;
if (sb_dsp_get_byte(devc) != 0x12)
return 0;
/*
* OK so far. Now configure the IRQ and DMA channel used by the card.
*/
if (hw_config->irq < 1 || hw_config->irq > 15 || jazz_irq_bits[hw_config->irq] == 0)
{
printk(KERN_ERR "Jazz16: Invalid interrupt (IRQ%d)\n", hw_config->irq);
return 0;
}
if (hw_config->dma < 0 || hw_config->dma > 3 || jazz_dma_bits[hw_config->dma] == 0)
{
printk(KERN_ERR "Jazz16: Invalid 8 bit DMA (DMA%d)\n", hw_config->dma);
return 0;
}
if (hw_config->dma2 < 0)
{
printk(KERN_ERR "Jazz16: No 16 bit DMA channel defined\n");
return 0;
}
if (hw_config->dma2 < 5 || hw_config->dma2 > 7 || jazz_dma_bits[hw_config->dma2] == 0)
{
printk(KERN_ERR "Jazz16: Invalid 16 bit DMA (DMA%d)\n", hw_config->dma2);
return 0;
}
devc->dma16 = hw_config->dma2;
if (!sb_dsp_command(devc, 0xfb))
return 0;
if (!sb_dsp_command(devc, jazz_dma_bits[hw_config->dma] |
(jazz_dma_bits[hw_config->dma2] << 4)))
return 0;
if (!sb_dsp_command(devc, jazz_irq_bits[hw_config->irq]))
return 0;
/*
* Now we have configured a standard Jazz16 device.
*/
devc->model = MDL_JAZZ;
strcpy(name, "Jazz16");
hw_config->name = "Jazz16";
devc->caps |= SB_NO_MIDI;
return 1;
}
static void relocate_ess1688(sb_devc * devc)
{
unsigned char bits;
switch (devc->base)
{
case 0x220:
bits = 0x04;
break;
case 0x230:
bits = 0x05;
break;
case 0x240:
bits = 0x06;
break;
case 0x250:
bits = 0x07;
break;
default:
return; /* Wrong port */
}
DDB(printk("Doing ESS1688 address selection\n"));
/*
* ES1688 supports two alternative ways for software address config.
* First try the so called Read-Sequence-Key method.
*/
/* Reset the sequence logic */
inb(0x229);
inb(0x229);
inb(0x229);
/* Perform the read sequence */
inb(0x22b);
inb(0x229);
inb(0x22b);
inb(0x229);
inb(0x229);
inb(0x22b);
inb(0x229);
/* Select the base address by reading from it. Then probe using the port. */
inb(devc->base);
if (sb_dsp_reset(devc)) /* Bingo */
return;
#if 0 /* This causes system lockups (Nokia 386/25 at least) */
/*
* The last resort is the system control register method.
*/
outb((0x00), 0xfb); /* 0xFB is the unlock register */
outb((0x00), 0xe0); /* Select index 0 */
outb((bits), 0xe1); /* Write the config bits */
outb((0x00), 0xf9); /* 0xFB is the lock register */
#endif
}
int sb_dsp_detect(struct address_info *hw_config, int pci, int pciio, struct sb_module_options *sbmo)
{
sb_devc sb_info;
sb_devc *devc = &sb_info;
memset((char *) &sb_info, 0, sizeof(sb_info)); /* Zero everything */
/* Copy module options in place */
if(sbmo) memcpy(&devc->sbmo, sbmo, sizeof(struct sb_module_options));
sb_info.my_mididev = -1;
sb_info.my_mixerdev = -1;
sb_info.dev = -1;
/*
* Initialize variables
*/
DDB(printk("sb_dsp_detect(%x) entered\n", hw_config->io_base));
spin_lock_init(&devc->lock);
devc->type = hw_config->card_subtype;
devc->base = hw_config->io_base;
devc->irq = hw_config->irq;
devc->dma8 = hw_config->dma;
devc->dma16 = -1;
devc->pcibase = pciio;
if(pci == SB_PCI_ESSMAESTRO)
{
devc->model = MDL_ESSPCI;
devc->caps |= SB_PCI_IRQ;
hw_config->driver_use_1 |= SB_PCI_IRQ;
hw_config->card_subtype = MDL_ESSPCI;
}
if(pci == SB_PCI_YAMAHA)
{
devc->model = MDL_YMPCI;
devc->caps |= SB_PCI_IRQ;
hw_config->driver_use_1 |= SB_PCI_IRQ;
hw_config->card_subtype = MDL_YMPCI;
printk("Yamaha PCI mode.\n");
}
if (devc->sbmo.acer)
{
unsigned long flags;
spin_lock_irqsave(&devc->lock, flags);
inb(devc->base + 0x09);
inb(devc->base + 0x09);
inb(devc->base + 0x09);
inb(devc->base + 0x0b);
inb(devc->base + 0x09);
inb(devc->base + 0x0b);
inb(devc->base + 0x09);
inb(devc->base + 0x09);
inb(devc->base + 0x0b);
inb(devc->base + 0x09);
inb(devc->base + 0x00);
spin_unlock_irqrestore(&devc->lock, flags);
}
/*
* Detect the device
*/
if (sb_dsp_reset(devc))
dsp_get_vers(devc);
else
devc->major = 0;
if (devc->type == 0 || devc->type == MDL_JAZZ || devc->type == MDL_SMW)
if (devc->major == 0 || (devc->major == 3 && devc->minor == 1))
relocate_Jazz16(devc, hw_config);
if (devc->major == 0 && (devc->type == MDL_ESS || devc->type == 0))
relocate_ess1688(devc);
if (!sb_dsp_reset(devc))
{
DDB(printk("SB reset failed\n"));
#ifdef MODULE
printk(KERN_INFO "sb: dsp reset failed.\n");
#endif
return 0;
}
if (devc->major == 0)
dsp_get_vers(devc);
if (devc->major == 3 && devc->minor == 1)
{
if (devc->type == MDL_AZTECH) /* SG Washington? */
{
if (sb_dsp_command(devc, 0x09))
if (sb_dsp_command(devc, 0x00)) /* Enter WSS mode */
{
int i;
/* Have some delay */
for (i = 0; i < 10000; i++)
inb(DSP_DATA_AVAIL);
devc->caps = SB_NO_AUDIO | SB_NO_MIDI; /* Mixer only */
devc->model = MDL_AZTECH;
}
}
}
if(devc->type == MDL_ESSPCI)
devc->model = MDL_ESSPCI;
if(devc->type == MDL_YMPCI)
{
printk("YMPCI selected\n");
devc->model = MDL_YMPCI;
}
/*
* Save device information for sb_dsp_init()
*/
detected_devc = kmalloc(sizeof(sb_devc), GFP_KERNEL);
if (detected_devc == NULL)
{
printk(KERN_ERR "sb: Can't allocate memory for device information\n");
return 0;
}
memcpy(detected_devc, devc, sizeof(sb_devc));
MDB(printk(KERN_INFO "SB %d.%02d detected OK (%x)\n", devc->major, devc->minor, hw_config->io_base));
return 1;
}
int sb_dsp_init(struct address_info *hw_config, struct module *owner)
{
sb_devc *devc;
char name[100];
extern int sb_be_quiet;
int mixer22, mixer30;
/*
* Check if we had detected a SB device earlier
*/
DDB(printk("sb_dsp_init(%x) entered\n", hw_config->io_base));
name[0] = 0;
if (detected_devc == NULL)
{
MDB(printk("No detected device\n"));
return 0;
}
devc = detected_devc;
detected_devc = NULL;
if (devc->base != hw_config->io_base)
{
DDB(printk("I/O port mismatch\n"));
release_region(devc->base, 16);
return 0;
}
/*
* Now continue initialization of the device
*/
devc->caps = hw_config->driver_use_1;
if (!((devc->caps & SB_NO_AUDIO) && (devc->caps & SB_NO_MIDI)) && hw_config->irq > 0)
{ /* IRQ setup */
/*
* ESS PCI cards do shared PCI IRQ stuff. Since they
* will get shared PCI irq lines we must cope.
*/
int i=(devc->caps&SB_PCI_IRQ)?IRQF_SHARED:0;
if (request_irq(hw_config->irq, sbintr, i, "soundblaster", devc) < 0)
{
printk(KERN_ERR "SB: Can't allocate IRQ%d\n", hw_config->irq);
release_region(devc->base, 16);
return 0;
}
devc->irq_ok = 0;
if (devc->major == 4)
if (!sb16_set_irq_hw(devc, devc->irq)) /* Unsupported IRQ */
{
free_irq(devc->irq, devc);
release_region(devc->base, 16);
return 0;
}
if ((devc->type == 0 || devc->type == MDL_ESS) &&
devc->major == 3 && devc->minor == 1)
{ /* Handle various chipsets which claim they are SB Pro compatible */
if ((devc->type != 0 && devc->type != MDL_ESS) ||
!ess_init(devc, hw_config))
{
if ((devc->type != 0 && devc->type != MDL_JAZZ &&
devc->type != MDL_SMW) || !init_Jazz16(devc, hw_config))
{
DDB(printk("This is a genuine SB Pro\n"));
}
}
}
if (devc->major == 4 && devc->minor <= 11 ) /* Won't work */
devc->irq_ok = 1;
else
{
int n;
for (n = 0; n < 3 && devc->irq_ok == 0; n++)
{
if (sb_dsp_command(devc, 0xf2)) /* Cause interrupt immediately */
{
int i;
for (i = 0; !devc->irq_ok && i < 10000; i++);
}
}
if (!devc->irq_ok)
printk(KERN_WARNING "sb: Interrupt test on IRQ%d failed - Probable IRQ conflict\n", devc->irq);
else
{
DDB(printk("IRQ test OK (IRQ%d)\n", devc->irq));
}
}
} /* IRQ setup */
last_sb = devc;
switch (devc->major)
{
case 1: /* SB 1.0 or 1.5 */
devc->model = hw_config->card_subtype = MDL_SB1;
break;
case 2: /* SB 2.x */
if (devc->minor == 0)
devc->model = hw_config->card_subtype = MDL_SB2;
else
devc->model = hw_config->card_subtype = MDL_SB201;
break;
case 3: /* SB Pro and most clones */
switch (devc->model) {
case 0:
devc->model = hw_config->card_subtype = MDL_SBPRO;
if (hw_config->name == NULL)
hw_config->name = "Sound Blaster Pro (8 BIT ONLY)";
break;
case MDL_ESS:
ess_dsp_init(devc, hw_config);
break;
}
break;
case 4:
devc->model = hw_config->card_subtype = MDL_SB16;
/*
* ALS007 and ALS100 return DSP version 4.2 and have 2 post-reset !=0
* registers at 0x3c and 0x4c (output ctrl registers on ALS007) whereas
* a "standard" SB16 doesn't have a register at 0x4c. ALS100 actively
* updates register 0x22 whenever 0x30 changes, as per the SB16 spec.
* Since ALS007 doesn't, this can be used to differentiate the 2 cards.
*/
if ((devc->minor == 2) && sb_getmixer(devc,0x3c) && sb_getmixer(devc,0x4c))
{
mixer30 = sb_getmixer(devc,0x30);
sb_setmixer(devc,0x22,(mixer22=sb_getmixer(devc,0x22)) & 0x0f);
sb_setmixer(devc,0x30,0xff);
/* ALS100 will force 0x30 to 0xf8 like SB16; ALS007 will allow 0xff. */
/* Register 0x22 & 0xf0 on ALS100 == 0xf0; on ALS007 it == 0x10. */
if ((sb_getmixer(devc,0x30) != 0xff) || ((sb_getmixer(devc,0x22) & 0xf0) != 0x10))
{
devc->submodel = SUBMDL_ALS100;
if (hw_config->name == NULL)
hw_config->name = "Sound Blaster 16 (ALS-100)";
}
else
{
sb_setmixer(devc,0x3c,0x1f); /* Enable all inputs */
sb_setmixer(devc,0x4c,0x1f);
sb_setmixer(devc,0x22,mixer22); /* Restore 0x22 to original value */
devc->submodel = SUBMDL_ALS007;
if (hw_config->name == NULL)
hw_config->name = "Sound Blaster 16 (ALS-007)";
}
sb_setmixer(devc,0x30,mixer30);
}
else if (hw_config->name == NULL)
hw_config->name = "Sound Blaster 16";
if (hw_config->dma2 == -1)
devc->dma16 = devc->dma8;
else if (hw_config->dma2 < 5 || hw_config->dma2 > 7)
{
printk(KERN_WARNING "SB16: Bad or missing 16 bit DMA channel\n");
devc->dma16 = devc->dma8;
}
else
devc->dma16 = hw_config->dma2;
if(!sb16_set_dma_hw(devc)) {
free_irq(devc->irq, devc);
release_region(hw_config->io_base, 16);
return 0;
}
devc->caps |= SB_NO_MIDI;
}
if (!(devc->caps & SB_NO_MIXER))
if (devc->major == 3 || devc->major == 4)
sb_mixer_init(devc, owner);
if (!(devc->caps & SB_NO_MIDI))
sb_dsp_midi_init(devc, owner);
if (hw_config->name == NULL)
hw_config->name = "Sound Blaster (8 BIT/MONO ONLY)";
sprintf(name, "%s (%d.%02d)", hw_config->name, devc->major, devc->minor);
conf_printf(name, hw_config);
/*
* Assuming that a sound card is Sound Blaster (compatible) is the most common
* configuration error and the mother of all problems. Usually sound cards
* emulate SB Pro but in addition they have a 16 bit native mode which should be
* used in Unix. See Readme.cards for more information about configuring OSS/Free
* properly.
*/
if (devc->model <= MDL_SBPRO)
{
if (devc->major == 3 && devc->minor != 1) /* "True" SB Pro should have v3.1 (rare ones may have 3.2). */
{
printk(KERN_INFO "This sound card may not be fully Sound Blaster Pro compatible.\n");
printk(KERN_INFO "In many cases there is another way to configure OSS so that\n");
printk(KERN_INFO "it works properly with OSS (for example in 16 bit mode).\n");
printk(KERN_INFO "Please ignore this message if you _really_ have a SB Pro.\n");
}
else if (!sb_be_quiet && devc->model == MDL_SBPRO)
{
printk(KERN_INFO "SB DSP version is just %d.%02d which means that your card is\n", devc->major, devc->minor);
printk(KERN_INFO "several years old (8 bit only device) or alternatively the sound driver\n");
printk(KERN_INFO "is incorrectly configured.\n");
}
}
hw_config->card_subtype = devc->model;
hw_config->slots[0]=devc->dev;
last_devc = devc; /* For SB MPU detection */
if (!(devc->caps & SB_NO_AUDIO) && devc->dma8 >= 0)
{
if (sound_alloc_dma(devc->dma8, "SoundBlaster8"))
{
printk(KERN_WARNING "Sound Blaster: Can't allocate 8 bit DMA channel %d\n", devc->dma8);
}
if (devc->dma16 >= 0 && devc->dma16 != devc->dma8)
{
if (sound_alloc_dma(devc->dma16, "SoundBlaster16"))
printk(KERN_WARNING "Sound Blaster: can't allocate 16 bit DMA channel %d.\n", devc->dma16);
}
sb_audio_init(devc, name, owner);
hw_config->slots[0]=devc->dev;
}
else
{
MDB(printk("Sound Blaster: no audio devices found.\n"));
}
return 1;
}
/* if (sbmpu) below we allow mpu401 to manage the midi devs
otherwise we have to unload them. (Andrzej Krzysztofowicz) */
void sb_dsp_unload(struct address_info *hw_config, int sbmpu)
{
sb_devc *devc;
devc = audio_devs[hw_config->slots[0]]->devc;
if (devc && devc->base == hw_config->io_base)
{
if ((devc->model & MDL_ESS) && devc->pcibase)
release_region(devc->pcibase, 8);
release_region(devc->base, 16);
if (!(devc->caps & SB_NO_AUDIO))
{
sound_free_dma(devc->dma8);
if (devc->dma16 >= 0)
sound_free_dma(devc->dma16);
}
if (!(devc->caps & SB_NO_AUDIO && devc->caps & SB_NO_MIDI))
{
if (devc->irq > 0)
free_irq(devc->irq, devc);
sb_mixer_unload(devc);
/* We don't have to do this bit any more the UART401 is its own
master -- Krzysztof Halasa */
/* But we have to do it, if UART401 is not detected */
if (!sbmpu)
sound_unload_mididev(devc->my_mididev);
sound_unload_audiodev(devc->dev);
}
kfree(devc);
}
else
release_region(hw_config->io_base, 16);
kfree(detected_devc);
}
/*
* Mixer access routines
*
* ES1887 modifications: some mixer registers reside in the
* range above 0xa0. These must be accessed in another way.
*/
void sb_setmixer(sb_devc * devc, unsigned int port, unsigned int value)
{
unsigned long flags;
if (devc->model == MDL_ESS) {
ess_setmixer (devc, port, value);
return;
}
spin_lock_irqsave(&devc->lock, flags);
outb(((unsigned char) (port & 0xff)), MIXER_ADDR);
udelay(20);
outb(((unsigned char) (value & 0xff)), MIXER_DATA);
udelay(20);
spin_unlock_irqrestore(&devc->lock, flags);
}
unsigned int sb_getmixer(sb_devc * devc, unsigned int port)
{
unsigned int val;
unsigned long flags;
if (devc->model == MDL_ESS) return ess_getmixer (devc, port);
spin_lock_irqsave(&devc->lock, flags);
outb(((unsigned char) (port & 0xff)), MIXER_ADDR);
udelay(20);
val = inb(MIXER_DATA);
udelay(20);
spin_unlock_irqrestore(&devc->lock, flags);
return val;
}
void sb_chgmixer
(sb_devc * devc, unsigned int reg, unsigned int mask, unsigned int val)
{
int value;
value = sb_getmixer(devc, reg);
value = (value & ~mask) | (val & mask);
sb_setmixer(devc, reg, value);
}
/*
* MPU401 MIDI initialization.
*/
static void smw_putmem(sb_devc * devc, int base, int addr, unsigned char val)
{
unsigned long flags;
spin_lock_irqsave(&jazz16_lock, flags); /* NOT the SB card? */
outb((addr & 0xff), base + 1); /* Low address bits */
outb((addr >> 8), base + 2); /* High address bits */
outb((val), base); /* Data */
spin_unlock_irqrestore(&jazz16_lock, flags);
}
static unsigned char smw_getmem(sb_devc * devc, int base, int addr)
{
unsigned long flags;
unsigned char val;
spin_lock_irqsave(&jazz16_lock, flags); /* NOT the SB card? */
outb((addr & 0xff), base + 1); /* Low address bits */
outb((addr >> 8), base + 2); /* High address bits */
val = inb(base); /* Data */
spin_unlock_irqrestore(&jazz16_lock, flags);
return val;
}
static int smw_midi_init(sb_devc * devc, struct address_info *hw_config)
{
int mpu_base = hw_config->io_base;
int mp_base = mpu_base + 4; /* Microcontroller base */
int i;
unsigned char control;
/*
* Reset the microcontroller so that the RAM can be accessed
*/
control = inb(mpu_base + 7);
outb((control | 3), mpu_base + 7); /* Set last two bits to 1 (?) */
outb(((control & 0xfe) | 2), mpu_base + 7); /* xxxxxxx0 resets the mc */
mdelay(3); /* Wait at least 1ms */
outb((control & 0xfc), mpu_base + 7); /* xxxxxx00 enables RAM */
/*
* Detect microcontroller by probing the 8k RAM area
*/
smw_putmem(devc, mp_base, 0, 0x00);
smw_putmem(devc, mp_base, 1, 0xff);
udelay(10);
if (smw_getmem(devc, mp_base, 0) != 0x00 || smw_getmem(devc, mp_base, 1) != 0xff)
{
DDB(printk("SM Wave: No microcontroller RAM detected (%02x, %02x)\n", smw_getmem(devc, mp_base, 0), smw_getmem(devc, mp_base, 1)));
return 0; /* No RAM */
}
/*
* There is RAM so assume it's really a SM Wave
*/
devc->model = MDL_SMW;
smw_mixer_init(devc);
#ifdef MODULE
if (!smw_ucode)
{
smw_ucodeLen = mod_firmware_load("/etc/sound/midi0001.bin", (void *) &smw_ucode);
smw_free = smw_ucode;
}
#endif
if (smw_ucodeLen > 0)
{
if (smw_ucodeLen != 8192)
{
printk(KERN_ERR "SM Wave: Invalid microcode (MIDI0001.BIN) length\n");
return 1;
}
/*
* Download microcode
*/
for (i = 0; i < 8192; i++)
smw_putmem(devc, mp_base, i, smw_ucode[i]);
/*
* Verify microcode
*/
for (i = 0; i < 8192; i++)
if (smw_getmem(devc, mp_base, i) != smw_ucode[i])
{
printk(KERN_ERR "SM Wave: Microcode verification failed\n");
return 0;
}
}
control = 0;
#ifdef SMW_SCSI_IRQ
/*
* Set the SCSI interrupt (IRQ2/9, IRQ3 or IRQ10). The SCSI interrupt
* is disabled by default.
*
* FIXME - make this a module option
*
* BTW the Zilog 5380 SCSI controller is located at MPU base + 0x10.
*/
{
static unsigned char scsi_irq_bits[] = {
0, 0, 3, 1, 0, 0, 0, 0, 0, 3, 2, 0, 0, 0, 0, 0
};
control |= scsi_irq_bits[SMW_SCSI_IRQ] << 6;
}
#endif
#ifdef SMW_OPL4_ENABLE
/*
* Make the OPL4 chip visible on the PC bus at 0x380.
*
* There is no need to enable this feature since this driver
* doesn't support OPL4 yet. Also there is no RAM in SM Wave so
* enabling OPL4 is pretty useless.
*/
control |= 0x10; /* Uses IRQ12 if bit 0x20 == 0 */
/* control |= 0x20; Uncomment this if you want to use IRQ7 */
#endif
outb((control | 0x03), mpu_base + 7); /* xxxxxx11 restarts */
hw_config->name = "SoundMan Wave";
return 1;
}
static int init_Jazz16_midi(sb_devc * devc, struct address_info *hw_config)
{
int mpu_base = hw_config->io_base;
int sb_base = devc->base;
int irq = hw_config->irq;
unsigned char bits = 0;
unsigned long flags;
if (irq < 0)
irq *= -1;
if (irq < 1 || irq > 15 ||
jazz_irq_bits[irq] == 0)
{
printk(KERN_ERR "Jazz16: Invalid MIDI interrupt (IRQ%d)\n", irq);
return 0;
}
switch (sb_base)
{
case 0x220:
bits = 1;
break;
case 0x240:
bits = 2;
break;
case 0x260:
bits = 3;
break;
default:
return 0;
}
bits = jazz16_bits = bits << 5;
switch (mpu_base)
{
case 0x310:
bits |= 1;
break;
case 0x320:
bits |= 2;
break;
case 0x330:
bits |= 3;
break;
default:
printk(KERN_ERR "Jazz16: Invalid MIDI I/O port %x\n", mpu_base);
return 0;
}
/*
* Magic wake up sequence by writing to 0x201 (aka Joystick port)
*/
spin_lock_irqsave(&jazz16_lock, flags);
outb(0xAF, 0x201);
outb(0x50, 0x201);
outb(bits, 0x201);
spin_unlock_irqrestore(&jazz16_lock, flags);
hw_config->name = "Jazz16";
smw_midi_init(devc, hw_config);
if (!sb_dsp_command(devc, 0xfb))
return 0;
if (!sb_dsp_command(devc, jazz_dma_bits[devc->dma8] |
(jazz_dma_bits[devc->dma16] << 4)))
return 0;
if (!sb_dsp_command(devc, jazz_irq_bits[devc->irq] |
(jazz_irq_bits[irq] << 4)))
return 0;
return 1;
}
int probe_sbmpu(struct address_info *hw_config, struct module *owner)
{
sb_devc *devc = last_devc;
int ret;
if (last_devc == NULL)
return 0;
last_devc = NULL;
if (hw_config->io_base <= 0)
{
/* The real vibra16 is fine about this, but we have to go
wipe up after Cyrix again */
if(devc->model == MDL_SB16 && devc->minor >= 12)
{
unsigned char bits = sb_getmixer(devc, 0x84) & ~0x06;
sb_setmixer(devc, 0x84, bits | 0x02); /* Disable MPU */
}
return 0;
}
#if defined(CONFIG_SOUND_MPU401)
if (devc->model == MDL_ESS)
{
struct resource *ports;
ports = request_region(hw_config->io_base, 2, "mpu401");
if (!ports) {
printk(KERN_ERR "sbmpu: I/O port conflict (%x)\n", hw_config->io_base);
return 0;
}
if (!ess_midi_init(devc, hw_config)) {
release_region(hw_config->io_base, 2);
return 0;
}
hw_config->name = "ESS1xxx MPU";
devc->midi_irq_cookie = NULL;
if (!probe_mpu401(hw_config, ports)) {
release_region(hw_config->io_base, 2);
return 0;
}
attach_mpu401(hw_config, owner);
if (last_sb->irq == -hw_config->irq)
last_sb->midi_irq_cookie =
(void *)(long) hw_config->slots[1];
return 1;
}
#endif
switch (devc->model)
{
case MDL_SB16:
if (hw_config->io_base != 0x300 && hw_config->io_base != 0x330)
{
printk(KERN_ERR "SB16: Invalid MIDI port %x\n", hw_config->io_base);
return 0;
}
hw_config->name = "Sound Blaster 16";
if (hw_config->irq < 3 || hw_config->irq == devc->irq)
hw_config->irq = -devc->irq;
if (devc->minor > 12) /* What is Vibra's version??? */
sb16_set_mpu_port(devc, hw_config);
break;
case MDL_JAZZ:
if (hw_config->irq < 3 || hw_config->irq == devc->irq)
hw_config->irq = -devc->irq;
if (!init_Jazz16_midi(devc, hw_config))
return 0;
break;
case MDL_YMPCI:
hw_config->name = "Yamaha PCI Legacy";
printk("Yamaha PCI legacy UART401 check.\n");
break;
default:
return 0;
}
ret = probe_uart401(hw_config, owner);
if (ret)
last_sb->midi_irq_cookie=midi_devs[hw_config->slots[4]]->devc;
return ret;
}
void unload_sbmpu(struct address_info *hw_config)
{
#if defined(CONFIG_SOUND_MPU401)
if (!strcmp (hw_config->name, "ESS1xxx MPU")) {
unload_mpu401(hw_config);
return;
}
#endif
unload_uart401(hw_config);
}
EXPORT_SYMBOL(sb_dsp_init);
EXPORT_SYMBOL(sb_dsp_detect);
EXPORT_SYMBOL(sb_dsp_unload);
EXPORT_SYMBOL(sb_be_quiet);
EXPORT_SYMBOL(probe_sbmpu);
EXPORT_SYMBOL(unload_sbmpu);
EXPORT_SYMBOL(smw_free);
MODULE_LICENSE("GPL");