- 根目录:
- arch
- arm
- common
- sa1111.c
/*
* linux/arch/arm/common/sa1111.c
*
* SA1111 support
*
* Original code by John Dorsey
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This file contains all generic SA1111 support.
*
* All initialization functions provided here are intended to be called
* from machine specific code with proper arguments when required.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <linux/dma-mapping.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/sizes.h>
#include <asm/hardware/sa1111.h>
/* SA1111 IRQs */
#define IRQ_GPAIN0 (0)
#define IRQ_GPAIN1 (1)
#define IRQ_GPAIN2 (2)
#define IRQ_GPAIN3 (3)
#define IRQ_GPBIN0 (4)
#define IRQ_GPBIN1 (5)
#define IRQ_GPBIN2 (6)
#define IRQ_GPBIN3 (7)
#define IRQ_GPBIN4 (8)
#define IRQ_GPBIN5 (9)
#define IRQ_GPCIN0 (10)
#define IRQ_GPCIN1 (11)
#define IRQ_GPCIN2 (12)
#define IRQ_GPCIN3 (13)
#define IRQ_GPCIN4 (14)
#define IRQ_GPCIN5 (15)
#define IRQ_GPCIN6 (16)
#define IRQ_GPCIN7 (17)
#define IRQ_MSTXINT (18)
#define IRQ_MSRXINT (19)
#define IRQ_MSSTOPERRINT (20)
#define IRQ_TPTXINT (21)
#define IRQ_TPRXINT (22)
#define IRQ_TPSTOPERRINT (23)
#define SSPXMTINT (24)
#define SSPRCVINT (25)
#define SSPROR (26)
#define AUDXMTDMADONEA (32)
#define AUDRCVDMADONEA (33)
#define AUDXMTDMADONEB (34)
#define AUDRCVDMADONEB (35)
#define AUDTFSR (36)
#define AUDRFSR (37)
#define AUDTUR (38)
#define AUDROR (39)
#define AUDDTS (40)
#define AUDRDD (41)
#define AUDSTO (42)
#define IRQ_USBPWR (43)
#define IRQ_HCIM (44)
#define IRQ_HCIBUFFACC (45)
#define IRQ_HCIRMTWKP (46)
#define IRQ_NHCIMFCIR (47)
#define IRQ_USB_PORT_RESUME (48)
#define IRQ_S0_READY_NINT (49)
#define IRQ_S1_READY_NINT (50)
#define IRQ_S0_CD_VALID (51)
#define IRQ_S1_CD_VALID (52)
#define IRQ_S0_BVD1_STSCHG (53)
#define IRQ_S1_BVD1_STSCHG (54)
extern void __init sa1110_mb_enable(void);
/*
* We keep the following data for the overall SA1111. Note that the
* struct device and struct resource are "fake"; they should be supplied
* by the bus above us. However, in the interests of getting all SA1111
* drivers converted over to the device model, we provide this as an
* anchor point for all the other drivers.
*/
struct sa1111 {
struct device *dev;
struct clk *clk;
unsigned long phys;
int irq;
int irq_base; /* base for cascaded on-chip IRQs */
spinlock_t lock;
void __iomem *base;
#ifdef CONFIG_PM
void *saved_state;
#endif
};
/*
* We _really_ need to eliminate this. Its only users
* are the PWM and DMA checking code.
*/
static struct sa1111 *g_sa1111;
struct sa1111_dev_info {
unsigned long offset;
unsigned long skpcr_mask;
unsigned int devid;
unsigned int irq[6];
};
static struct sa1111_dev_info sa1111_devices[] = {
{
.offset = SA1111_USB,
.skpcr_mask = SKPCR_UCLKEN,
.devid = SA1111_DEVID_USB,
.irq = {
IRQ_USBPWR,
IRQ_HCIM,
IRQ_HCIBUFFACC,
IRQ_HCIRMTWKP,
IRQ_NHCIMFCIR,
IRQ_USB_PORT_RESUME
},
},
{
.offset = 0x0600,
.skpcr_mask = SKPCR_I2SCLKEN | SKPCR_L3CLKEN,
.devid = SA1111_DEVID_SAC,
.irq = {
AUDXMTDMADONEA,
AUDXMTDMADONEB,
AUDRCVDMADONEA,
AUDRCVDMADONEB
},
},
{
.offset = 0x0800,
.skpcr_mask = SKPCR_SCLKEN,
.devid = SA1111_DEVID_SSP,
},
{
.offset = SA1111_KBD,
.skpcr_mask = SKPCR_PTCLKEN,
.devid = SA1111_DEVID_PS2,
.irq = {
IRQ_TPRXINT,
IRQ_TPTXINT
},
},
{
.offset = SA1111_MSE,
.skpcr_mask = SKPCR_PMCLKEN,
.devid = SA1111_DEVID_PS2,
.irq = {
IRQ_MSRXINT,
IRQ_MSTXINT
},
},
{
.offset = 0x1800,
.skpcr_mask = 0,
.devid = SA1111_DEVID_PCMCIA,
.irq = {
IRQ_S0_READY_NINT,
IRQ_S0_CD_VALID,
IRQ_S0_BVD1_STSCHG,
IRQ_S1_READY_NINT,
IRQ_S1_CD_VALID,
IRQ_S1_BVD1_STSCHG,
},
},
};
void __init sa1111_adjust_zones(unsigned long *size, unsigned long *holes)
{
unsigned int sz = SZ_1M >> PAGE_SHIFT;
size[1] = size[0] - sz;
size[0] = sz;
}
/*
* SA1111 interrupt support. Since clearing an IRQ while there are
* active IRQs causes the interrupt output to pulse, the upper levels
* will call us again if there are more interrupts to process.
*/
static void
sa1111_irq_handler(unsigned int irq, struct irq_desc *desc)
{
unsigned int stat0, stat1, i;
struct sa1111 *sachip = irq_get_handler_data(irq);
void __iomem *mapbase = sachip->base + SA1111_INTC;
stat0 = sa1111_readl(mapbase + SA1111_INTSTATCLR0);
stat1 = sa1111_readl(mapbase + SA1111_INTSTATCLR1);
sa1111_writel(stat0, mapbase + SA1111_INTSTATCLR0);
desc->irq_data.chip->irq_ack(&desc->irq_data);
sa1111_writel(stat1, mapbase + SA1111_INTSTATCLR1);
if (stat0 == 0 && stat1 == 0) {
do_bad_IRQ(irq, desc);
return;
}
for (i = 0; stat0; i++, stat0 >>= 1)
if (stat0 & 1)
generic_handle_irq(i + sachip->irq_base);
for (i = 32; stat1; i++, stat1 >>= 1)
if (stat1 & 1)
generic_handle_irq(i + sachip->irq_base);
/* For level-based interrupts */
desc->irq_data.chip->irq_unmask(&desc->irq_data);
}
#define SA1111_IRQMASK_LO(x) (1 << (x - sachip->irq_base))
#define SA1111_IRQMASK_HI(x) (1 << (x - sachip->irq_base - 32))
static void sa1111_ack_irq(struct irq_data *d)
{
}
static void sa1111_mask_lowirq(struct irq_data *d)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned long ie0;
ie0 = sa1111_readl(mapbase + SA1111_INTEN0);
ie0 &= ~SA1111_IRQMASK_LO(d->irq);
writel(ie0, mapbase + SA1111_INTEN0);
}
static void sa1111_unmask_lowirq(struct irq_data *d)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned long ie0;
ie0 = sa1111_readl(mapbase + SA1111_INTEN0);
ie0 |= SA1111_IRQMASK_LO(d->irq);
sa1111_writel(ie0, mapbase + SA1111_INTEN0);
}
/*
* Attempt to re-trigger the interrupt. The SA1111 contains a register
* (INTSET) which claims to do this. However, in practice no amount of
* manipulation of INTEN and INTSET guarantees that the interrupt will
* be triggered. In fact, its very difficult, if not impossible to get
* INTSET to re-trigger the interrupt.
*/
static int sa1111_retrigger_lowirq(struct irq_data *d)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned int mask = SA1111_IRQMASK_LO(d->irq);
unsigned long ip0;
int i;
ip0 = sa1111_readl(mapbase + SA1111_INTPOL0);
for (i = 0; i < 8; i++) {
sa1111_writel(ip0 ^ mask, mapbase + SA1111_INTPOL0);
sa1111_writel(ip0, mapbase + SA1111_INTPOL0);
if (sa1111_readl(mapbase + SA1111_INTSTATCLR0) & mask)
break;
}
if (i == 8)
printk(KERN_ERR "Danger Will Robinson: failed to "
"re-trigger IRQ%d\n", d->irq);
return i == 8 ? -1 : 0;
}
static int sa1111_type_lowirq(struct irq_data *d, unsigned int flags)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned int mask = SA1111_IRQMASK_LO(d->irq);
unsigned long ip0;
if (flags == IRQ_TYPE_PROBE)
return 0;
if ((!(flags & IRQ_TYPE_EDGE_RISING) ^ !(flags & IRQ_TYPE_EDGE_FALLING)) == 0)
return -EINVAL;
ip0 = sa1111_readl(mapbase + SA1111_INTPOL0);
if (flags & IRQ_TYPE_EDGE_RISING)
ip0 &= ~mask;
else
ip0 |= mask;
sa1111_writel(ip0, mapbase + SA1111_INTPOL0);
sa1111_writel(ip0, mapbase + SA1111_WAKEPOL0);
return 0;
}
static int sa1111_wake_lowirq(struct irq_data *d, unsigned int on)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned int mask = SA1111_IRQMASK_LO(d->irq);
unsigned long we0;
we0 = sa1111_readl(mapbase + SA1111_WAKEEN0);
if (on)
we0 |= mask;
else
we0 &= ~mask;
sa1111_writel(we0, mapbase + SA1111_WAKEEN0);
return 0;
}
static struct irq_chip sa1111_low_chip = {
.name = "SA1111-l",
.irq_ack = sa1111_ack_irq,
.irq_mask = sa1111_mask_lowirq,
.irq_unmask = sa1111_unmask_lowirq,
.irq_retrigger = sa1111_retrigger_lowirq,
.irq_set_type = sa1111_type_lowirq,
.irq_set_wake = sa1111_wake_lowirq,
};
static void sa1111_mask_highirq(struct irq_data *d)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned long ie1;
ie1 = sa1111_readl(mapbase + SA1111_INTEN1);
ie1 &= ~SA1111_IRQMASK_HI(d->irq);
sa1111_writel(ie1, mapbase + SA1111_INTEN1);
}
static void sa1111_unmask_highirq(struct irq_data *d)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned long ie1;
ie1 = sa1111_readl(mapbase + SA1111_INTEN1);
ie1 |= SA1111_IRQMASK_HI(d->irq);
sa1111_writel(ie1, mapbase + SA1111_INTEN1);
}
/*
* Attempt to re-trigger the interrupt. The SA1111 contains a register
* (INTSET) which claims to do this. However, in practice no amount of
* manipulation of INTEN and INTSET guarantees that the interrupt will
* be triggered. In fact, its very difficult, if not impossible to get
* INTSET to re-trigger the interrupt.
*/
static int sa1111_retrigger_highirq(struct irq_data *d)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned int mask = SA1111_IRQMASK_HI(d->irq);
unsigned long ip1;
int i;
ip1 = sa1111_readl(mapbase + SA1111_INTPOL1);
for (i = 0; i < 8; i++) {
sa1111_writel(ip1 ^ mask, mapbase + SA1111_INTPOL1);
sa1111_writel(ip1, mapbase + SA1111_INTPOL1);
if (sa1111_readl(mapbase + SA1111_INTSTATCLR1) & mask)
break;
}
if (i == 8)
printk(KERN_ERR "Danger Will Robinson: failed to "
"re-trigger IRQ%d\n", d->irq);
return i == 8 ? -1 : 0;
}
static int sa1111_type_highirq(struct irq_data *d, unsigned int flags)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned int mask = SA1111_IRQMASK_HI(d->irq);
unsigned long ip1;
if (flags == IRQ_TYPE_PROBE)
return 0;
if ((!(flags & IRQ_TYPE_EDGE_RISING) ^ !(flags & IRQ_TYPE_EDGE_FALLING)) == 0)
return -EINVAL;
ip1 = sa1111_readl(mapbase + SA1111_INTPOL1);
if (flags & IRQ_TYPE_EDGE_RISING)
ip1 &= ~mask;
else
ip1 |= mask;
sa1111_writel(ip1, mapbase + SA1111_INTPOL1);
sa1111_writel(ip1, mapbase + SA1111_WAKEPOL1);
return 0;
}
static int sa1111_wake_highirq(struct irq_data *d, unsigned int on)
{
struct sa1111 *sachip = irq_data_get_irq_chip_data(d);
void __iomem *mapbase = sachip->base + SA1111_INTC;
unsigned int mask = SA1111_IRQMASK_HI(d->irq);
unsigned long we1;
we1 = sa1111_readl(mapbase + SA1111_WAKEEN1);
if (on)
we1 |= mask;
else
we1 &= ~mask;
sa1111_writel(we1, mapbase + SA1111_WAKEEN1);
return 0;
}
static struct irq_chip sa1111_high_chip = {
.name = "SA1111-h",
.irq_ack = sa1111_ack_irq,
.irq_mask = sa1111_mask_highirq,
.irq_unmask = sa1111_unmask_highirq,
.irq_retrigger = sa1111_retrigger_highirq,
.irq_set_type = sa1111_type_highirq,
.irq_set_wake = sa1111_wake_highirq,
};
static void sa1111_setup_irq(struct sa1111 *sachip)
{
void __iomem *irqbase = sachip->base + SA1111_INTC;
unsigned int irq;
/*
* We're guaranteed that this region hasn't been taken.
*/
request_mem_region(sachip->phys + SA1111_INTC, 512, "irq");
/* disable all IRQs */
sa1111_writel(0, irqbase + SA1111_INTEN0);
sa1111_writel(0, irqbase + SA1111_INTEN1);
sa1111_writel(0, irqbase + SA1111_WAKEEN0);
sa1111_writel(0, irqbase + SA1111_WAKEEN1);
/*
* detect on rising edge. Note: Feb 2001 Errata for SA1111
* specifies that S0ReadyInt and S1ReadyInt should be '1'.
*/
sa1111_writel(0, irqbase + SA1111_INTPOL0);
sa1111_writel(SA1111_IRQMASK_HI(IRQ_S0_READY_NINT) |
SA1111_IRQMASK_HI(IRQ_S1_READY_NINT),
irqbase + SA1111_INTPOL1);
/* clear all IRQs */
sa1111_writel(~0, irqbase + SA1111_INTSTATCLR0);
sa1111_writel(~0, irqbase + SA1111_INTSTATCLR1);
for (irq = IRQ_GPAIN0; irq <= SSPROR; irq++) {
irq_set_chip_and_handler(irq, &sa1111_low_chip,
handle_edge_irq);
irq_set_chip_data(irq, sachip);
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
for (irq = AUDXMTDMADONEA; irq <= IRQ_S1_BVD1_STSCHG; irq++) {
irq_set_chip_and_handler(irq, &sa1111_high_chip,
handle_edge_irq);
irq_set_chip_data(irq, sachip);
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
/*
* Register SA1111 interrupt
*/
irq_set_irq_type(sachip->irq, IRQ_TYPE_EDGE_RISING);
irq_set_handler_data(sachip->irq, sachip);
irq_set_chained_handler(sachip->irq, sa1111_irq_handler);
}
/*
* Bring the SA1111 out of reset. This requires a set procedure:
* 1. nRESET asserted (by hardware)
* 2. CLK turned on from SA1110
* 3. nRESET deasserted
* 4. VCO turned on, PLL_BYPASS turned off
* 5. Wait lock time, then assert RCLKEn
* 7. PCR set to allow clocking of individual functions
*
* Until we've done this, the only registers we can access are:
* SBI_SKCR
* SBI_SMCR
* SBI_SKID
*/
static void sa1111_wake(struct sa1111 *sachip)
{
unsigned long flags, r;
spin_lock_irqsave(&sachip->lock, flags);
clk_enable(sachip->clk);
/*
* Turn VCO on, and disable PLL Bypass.
*/
r = sa1111_readl(sachip->base + SA1111_SKCR);
r &= ~SKCR_VCO_OFF;
sa1111_writel(r, sachip->base + SA1111_SKCR);
r |= SKCR_PLL_BYPASS | SKCR_OE_EN;
sa1111_writel(r, sachip->base + SA1111_SKCR);
/*
* Wait lock time. SA1111 manual _doesn't_
* specify a figure for this! We choose 100us.
*/
udelay(100);
/*
* Enable RCLK. We also ensure that RDYEN is set.
*/
r |= SKCR_RCLKEN | SKCR_RDYEN;
sa1111_writel(r, sachip->base + SA1111_SKCR);
/*
* Wait 14 RCLK cycles for the chip to finish coming out
* of reset. (RCLK=24MHz). This is 590ns.
*/
udelay(1);
/*
* Ensure all clocks are initially off.
*/
sa1111_writel(0, sachip->base + SA1111_SKPCR);
spin_unlock_irqrestore(&sachip->lock, flags);
}
#ifdef CONFIG_ARCH_SA1100
static u32 sa1111_dma_mask[] = {
~0,
~(1 << 20),
~(1 << 23),
~(1 << 24),
~(1 << 25),
~(1 << 20),
~(1 << 20),
0,
};
/*
* Configure the SA1111 shared memory controller.
*/
void
sa1111_configure_smc(struct sa1111 *sachip, int sdram, unsigned int drac,
unsigned int cas_latency)
{
unsigned int smcr = SMCR_DTIM | SMCR_MBGE | FInsrt(drac, SMCR_DRAC);
if (cas_latency == 3)
smcr |= SMCR_CLAT;
sa1111_writel(smcr, sachip->base + SA1111_SMCR);
/*
* Now clear the bits in the DMA mask to work around the SA1111
* DMA erratum (Intel StrongARM SA-1111 Microprocessor Companion
* Chip Specification Update, June 2000, Erratum #7).
*/
if (sachip->dev->dma_mask)
*sachip->dev->dma_mask &= sa1111_dma_mask[drac >> 2];
sachip->dev->coherent_dma_mask &= sa1111_dma_mask[drac >> 2];
}
#endif
static void sa1111_dev_release(struct device *_dev)
{
struct sa1111_dev *dev = SA1111_DEV(_dev);
release_resource(&dev->res);
kfree(dev);
}
static int
sa1111_init_one_child(struct sa1111 *sachip, struct resource *parent,
struct sa1111_dev_info *info)
{
struct sa1111_dev *dev;
int ret;
dev = kzalloc(sizeof(struct sa1111_dev), GFP_KERNEL);
if (!dev) {
ret = -ENOMEM;
goto out;
}
dev_set_name(&dev->dev, "%4.4lx", info->offset);
dev->devid = info->devid;
dev->dev.parent = sachip->dev;
dev->dev.bus = &sa1111_bus_type;
dev->dev.release = sa1111_dev_release;
dev->dev.coherent_dma_mask = sachip->dev->coherent_dma_mask;
dev->res.start = sachip->phys + info->offset;
dev->res.end = dev->res.start + 511;
dev->res.name = dev_name(&dev->dev);
dev->res.flags = IORESOURCE_MEM;
dev->mapbase = sachip->base + info->offset;
dev->skpcr_mask = info->skpcr_mask;
memmove(dev->irq, info->irq, sizeof(dev->irq));
ret = request_resource(parent, &dev->res);
if (ret) {
printk("SA1111: failed to allocate resource for %s\n",
dev->res.name);
dev_set_name(&dev->dev, NULL);
kfree(dev);
goto out;
}
ret = device_register(&dev->dev);
if (ret) {
release_resource(&dev->res);
kfree(dev);
goto out;
}
#ifdef CONFIG_DMABOUNCE
/*
* If the parent device has a DMA mask associated with it,
* propagate it down to the children.
*/
if (sachip->dev->dma_mask) {
dev->dma_mask = *sachip->dev->dma_mask;
dev->dev.dma_mask = &dev->dma_mask;
if (dev->dma_mask != 0xffffffffUL) {
ret = dmabounce_register_dev(&dev->dev, 1024, 4096);
if (ret) {
dev_err(&dev->dev, "SA1111: Failed to register"
" with dmabounce\n");
device_unregister(&dev->dev);
}
}
}
#endif
out:
return ret;
}
/**
* sa1111_probe - probe for a single SA1111 chip.
* @phys_addr: physical address of device.
*
* Probe for a SA1111 chip. This must be called
* before any other SA1111-specific code.
*
* Returns:
* %-ENODEV device not found.
* %-EBUSY physical address already marked in-use.
* %0 successful.
*/
static int __devinit
__sa1111_probe(struct device *me, struct resource *mem, int irq)
{
struct sa1111 *sachip;
unsigned long id;
unsigned int has_devs;
int i, ret = -ENODEV;
sachip = kzalloc(sizeof(struct sa1111), GFP_KERNEL);
if (!sachip)
return -ENOMEM;
sachip->clk = clk_get(me, "SA1111_CLK");
if (IS_ERR(sachip->clk)) {
ret = PTR_ERR(sachip->clk);
goto err_free;
}
spin_lock_init(&sachip->lock);
sachip->dev = me;
dev_set_drvdata(sachip->dev, sachip);
sachip->phys = mem->start;
sachip->irq = irq;
/*
* Map the whole region. This also maps the
* registers for our children.
*/
sachip->base = ioremap(mem->start, PAGE_SIZE * 2);
if (!sachip->base) {
ret = -ENOMEM;
goto err_clkput;
}
/*
* Probe for the chip. Only touch the SBI registers.
*/
id = sa1111_readl(sachip->base + SA1111_SKID);
if ((id & SKID_ID_MASK) != SKID_SA1111_ID) {
printk(KERN_DEBUG "SA1111 not detected: ID = %08lx\n", id);
ret = -ENODEV;
goto err_unmap;
}
printk(KERN_INFO "SA1111 Microprocessor Companion Chip: "
"silicon revision %lx, metal revision %lx\n",
(id & SKID_SIREV_MASK)>>4, (id & SKID_MTREV_MASK));
/*
* We found it. Wake the chip up, and initialise.
*/
sa1111_wake(sachip);
#ifdef CONFIG_ARCH_SA1100
{
unsigned int val;
/*
* The SDRAM configuration of the SA1110 and the SA1111 must
* match. This is very important to ensure that SA1111 accesses
* don't corrupt the SDRAM. Note that this ungates the SA1111's
* MBGNT signal, so we must have called sa1110_mb_disable()
* beforehand.
*/
sa1111_configure_smc(sachip, 1,
FExtr(MDCNFG, MDCNFG_SA1110_DRAC0),
FExtr(MDCNFG, MDCNFG_SA1110_TDL0));
/*
* We only need to turn on DCLK whenever we want to use the
* DMA. It can otherwise be held firmly in the off position.
* (currently, we always enable it.)
*/
val = sa1111_readl(sachip->base + SA1111_SKPCR);
sa1111_writel(val | SKPCR_DCLKEN, sachip->base + SA1111_SKPCR);
/*
* Enable the SA1110 memory bus request and grant signals.
*/
sa1110_mb_enable();
}
#endif
/*
* The interrupt controller must be initialised before any
* other device to ensure that the interrupts are available.
*/
if (sachip->irq != NO_IRQ)
sa1111_setup_irq(sachip);
g_sa1111 = sachip;
has_devs = ~0;
if (machine_is_assabet() || machine_is_jornada720() ||
machine_is_badge4())
has_devs &= ~(1 << 4);
else
has_devs &= ~(1 << 1);
for (i = 0; i < ARRAY_SIZE(sa1111_devices); i++)
if (has_devs & (1 << i))
sa1111_init_one_child(sachip, mem, &sa1111_devices[i]);
return 0;
err_unmap:
iounmap(sachip->base);
err_clkput:
clk_put(sachip->clk);
err_free:
kfree(sachip);
return ret;
}
static int sa1111_remove_one(struct device *dev, void *data)
{
device_unregister(dev);
return 0;
}
static void __sa1111_remove(struct sa1111 *sachip)
{
void __iomem *irqbase = sachip->base + SA1111_INTC;
device_for_each_child(sachip->dev, NULL, sa1111_remove_one);
/* disable all IRQs */
sa1111_writel(0, irqbase + SA1111_INTEN0);
sa1111_writel(0, irqbase + SA1111_INTEN1);
sa1111_writel(0, irqbase + SA1111_WAKEEN0);
sa1111_writel(0, irqbase + SA1111_WAKEEN1);
clk_disable(sachip->clk);
if (sachip->irq != NO_IRQ) {
irq_set_chained_handler(sachip->irq, NULL);
irq_set_handler_data(sachip->irq, NULL);
release_mem_region(sachip->phys + SA1111_INTC, 512);
}
iounmap(sachip->base);
clk_put(sachip->clk);
kfree(sachip);
}
/*
* According to the "Intel StrongARM SA-1111 Microprocessor Companion
* Chip Specification Update" (June 2000), erratum #7, there is a
* significant bug in the SA1111 SDRAM shared memory controller. If
* an access to a region of memory above 1MB relative to the bank base,
* it is important that address bit 10 _NOT_ be asserted. Depending
* on the configuration of the RAM, bit 10 may correspond to one
* of several different (processor-relative) address bits.
*
* This routine only identifies whether or not a given DMA address
* is susceptible to the bug.
*
* This should only get called for sa1111_device types due to the
* way we configure our device dma_masks.
*/
int dma_needs_bounce(struct device *dev, dma_addr_t addr, size_t size)
{
/*
* Section 4.6 of the "Intel StrongARM SA-1111 Development Module
* User's Guide" mentions that jumpers R51 and R52 control the
* target of SA-1111 DMA (either SDRAM bank 0 on Assabet, or
* SDRAM bank 1 on Neponset). The default configuration selects
* Assabet, so any address in bank 1 is necessarily invalid.
*/
return ((machine_is_assabet() || machine_is_pfs168()) &&
(addr >= 0xc8000000 || (addr + size) >= 0xc8000000));
}
struct sa1111_save_data {
unsigned int skcr;
unsigned int skpcr;
unsigned int skcdr;
unsigned char skaud;
unsigned char skpwm0;
unsigned char skpwm1;
/*
* Interrupt controller
*/
unsigned int intpol0;
unsigned int intpol1;
unsigned int inten0;
unsigned int inten1;
unsigned int wakepol0;
unsigned int wakepol1;
unsigned int wakeen0;
unsigned int wakeen1;
};
#ifdef CONFIG_PM
static int sa1111_suspend(struct platform_device *dev, pm_message_t state)
{
struct sa1111 *sachip = platform_get_drvdata(dev);
struct sa1111_save_data *save;
unsigned long flags;
unsigned int val;
void __iomem *base;
save = kmalloc(sizeof(struct sa1111_save_data), GFP_KERNEL);
if (!save)
return -ENOMEM;
sachip->saved_state = save;
spin_lock_irqsave(&sachip->lock, flags);
/*
* Save state.
*/
base = sachip->base;
save->skcr = sa1111_readl(base + SA1111_SKCR);
save->skpcr = sa1111_readl(base + SA1111_SKPCR);
save->skcdr = sa1111_readl(base + SA1111_SKCDR);
save->skaud = sa1111_readl(base + SA1111_SKAUD);
save->skpwm0 = sa1111_readl(base + SA1111_SKPWM0);
save->skpwm1 = sa1111_readl(base + SA1111_SKPWM1);
base = sachip->base + SA1111_INTC;
save->intpol0 = sa1111_readl(base + SA1111_INTPOL0);
save->intpol1 = sa1111_readl(base + SA1111_INTPOL1);
save->inten0 = sa1111_readl(base + SA1111_INTEN0);
save->inten1 = sa1111_readl(base + SA1111_INTEN1);
save->wakepol0 = sa1111_readl(base + SA1111_WAKEPOL0);
save->wakepol1 = sa1111_readl(base + SA1111_WAKEPOL1);
save->wakeen0 = sa1111_readl(base + SA1111_WAKEEN0);
save->wakeen1 = sa1111_readl(base + SA1111_WAKEEN1);
/*
* Disable.
*/
val = sa1111_readl(sachip->base + SA1111_SKCR);
sa1111_writel(val | SKCR_SLEEP, sachip->base + SA1111_SKCR);
sa1111_writel(0, sachip->base + SA1111_SKPWM0);
sa1111_writel(0, sachip->base + SA1111_SKPWM1);
clk_disable(sachip->clk);
spin_unlock_irqrestore(&sachip->lock, flags);
return 0;
}
/*
* sa1111_resume - Restore the SA1111 device state.
* @dev: device to restore
*
* Restore the general state of the SA1111; clock control and
* interrupt controller. Other parts of the SA1111 must be
* restored by their respective drivers, and must be called
* via LDM after this function.
*/
static int sa1111_resume(struct platform_device *dev)
{
struct sa1111 *sachip = platform_get_drvdata(dev);
struct sa1111_save_data *save;
unsigned long flags, id;
void __iomem *base;
save = sachip->saved_state;
if (!save)
return 0;
/*
* Ensure that the SA1111 is still here.
* FIXME: shouldn't do this here.
*/
id = sa1111_readl(sachip->base + SA1111_SKID);
if ((id & SKID_ID_MASK) != SKID_SA1111_ID) {
__sa1111_remove(sachip);
platform_set_drvdata(dev, NULL);
kfree(save);
return 0;
}
/*
* First of all, wake up the chip.
*/
sa1111_wake(sachip);
/*
* Only lock for write ops. Also, sa1111_wake must be called with
* released spinlock!
*/
spin_lock_irqsave(&sachip->lock, flags);
sa1111_writel(0, sachip->base + SA1111_INTC + SA1111_INTEN0);
sa1111_writel(0, sachip->base + SA1111_INTC + SA1111_INTEN1);
base = sachip->base;
sa1111_writel(save->skcr, base + SA1111_SKCR);
sa1111_writel(save->skpcr, base + SA1111_SKPCR);
sa1111_writel(save->skcdr, base + SA1111_SKCDR);
sa1111_writel(save->skaud, base + SA1111_SKAUD);
sa1111_writel(save->skpwm0, base + SA1111_SKPWM0);
sa1111_writel(save->skpwm1, base + SA1111_SKPWM1);
base = sachip->base + SA1111_INTC;
sa1111_writel(save->intpol0, base + SA1111_INTPOL0);
sa1111_writel(save->intpol1, base + SA1111_INTPOL1);
sa1111_writel(save->inten0, base + SA1111_INTEN0);
sa1111_writel(save->inten1, base + SA1111_INTEN1);
sa1111_writel(save->wakepol0, base + SA1111_WAKEPOL0);
sa1111_writel(save->wakepol1, base + SA1111_WAKEPOL1);
sa1111_writel(save->wakeen0, base + SA1111_WAKEEN0);
sa1111_writel(save->wakeen1, base + SA1111_WAKEEN1);
spin_unlock_irqrestore(&sachip->lock, flags);
sachip->saved_state = NULL;
kfree(save);
return 0;
}
#else
#define sa1111_suspend NULL
#define sa1111_resume NULL
#endif
static int __devinit sa1111_probe(struct platform_device *pdev)
{
struct resource *mem;
int irq;
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!mem)
return -EINVAL;
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return -ENXIO;
return __sa1111_probe(&pdev->dev, mem, irq);
}
static int sa1111_remove(struct platform_device *pdev)
{
struct sa1111 *sachip = platform_get_drvdata(pdev);
if (sachip) {
#ifdef CONFIG_PM
kfree(sachip->saved_state);
sachip->saved_state = NULL;
#endif
__sa1111_remove(sachip);
platform_set_drvdata(pdev, NULL);
}
return 0;
}
/*
* Not sure if this should be on the system bus or not yet.
* We really want some way to register a system device at
* the per-machine level, and then have this driver pick
* up the registered devices.
*
* We also need to handle the SDRAM configuration for
* PXA250/SA1110 machine classes.
*/
static struct platform_driver sa1111_device_driver = {
.probe = sa1111_probe,
.remove = sa1111_remove,
.suspend = sa1111_suspend,
.resume = sa1111_resume,
.driver = {
.name = "sa1111",
},
};
/*
* Get the parent device driver (us) structure
* from a child function device
*/
static inline struct sa1111 *sa1111_chip_driver(struct sa1111_dev *sadev)
{
return (struct sa1111 *)dev_get_drvdata(sadev->dev.parent);
}
/*
* The bits in the opdiv field are non-linear.
*/
static unsigned char opdiv_table[] = { 1, 4, 2, 8 };
static unsigned int __sa1111_pll_clock(struct sa1111 *sachip)
{
unsigned int skcdr, fbdiv, ipdiv, opdiv;
skcdr = sa1111_readl(sachip->base + SA1111_SKCDR);
fbdiv = (skcdr & 0x007f) + 2;
ipdiv = ((skcdr & 0x0f80) >> 7) + 2;
opdiv = opdiv_table[(skcdr & 0x3000) >> 12];
return 3686400 * fbdiv / (ipdiv * opdiv);
}
/**
* sa1111_pll_clock - return the current PLL clock frequency.
* @sadev: SA1111 function block
*
* BUG: we should look at SKCR. We also blindly believe that
* the chip is being fed with the 3.6864MHz clock.
*
* Returns the PLL clock in Hz.
*/
unsigned int sa1111_pll_clock(struct sa1111_dev *sadev)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
return __sa1111_pll_clock(sachip);
}
EXPORT_SYMBOL(sa1111_pll_clock);
/**
* sa1111_select_audio_mode - select I2S or AC link mode
* @sadev: SA1111 function block
* @mode: One of %SA1111_AUDIO_ACLINK or %SA1111_AUDIO_I2S
*
* Frob the SKCR to select AC Link mode or I2S mode for
* the audio block.
*/
void sa1111_select_audio_mode(struct sa1111_dev *sadev, int mode)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned long flags;
unsigned int val;
spin_lock_irqsave(&sachip->lock, flags);
val = sa1111_readl(sachip->base + SA1111_SKCR);
if (mode == SA1111_AUDIO_I2S) {
val &= ~SKCR_SELAC;
} else {
val |= SKCR_SELAC;
}
sa1111_writel(val, sachip->base + SA1111_SKCR);
spin_unlock_irqrestore(&sachip->lock, flags);
}
EXPORT_SYMBOL(sa1111_select_audio_mode);
/**
* sa1111_set_audio_rate - set the audio sample rate
* @sadev: SA1111 SAC function block
* @rate: sample rate to select
*/
int sa1111_set_audio_rate(struct sa1111_dev *sadev, int rate)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned int div;
if (sadev->devid != SA1111_DEVID_SAC)
return -EINVAL;
div = (__sa1111_pll_clock(sachip) / 256 + rate / 2) / rate;
if (div == 0)
div = 1;
if (div > 128)
div = 128;
sa1111_writel(div - 1, sachip->base + SA1111_SKAUD);
return 0;
}
EXPORT_SYMBOL(sa1111_set_audio_rate);
/**
* sa1111_get_audio_rate - get the audio sample rate
* @sadev: SA1111 SAC function block device
*/
int sa1111_get_audio_rate(struct sa1111_dev *sadev)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned long div;
if (sadev->devid != SA1111_DEVID_SAC)
return -EINVAL;
div = sa1111_readl(sachip->base + SA1111_SKAUD) + 1;
return __sa1111_pll_clock(sachip) / (256 * div);
}
EXPORT_SYMBOL(sa1111_get_audio_rate);
void sa1111_set_io_dir(struct sa1111_dev *sadev,
unsigned int bits, unsigned int dir,
unsigned int sleep_dir)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned long flags;
unsigned int val;
void __iomem *gpio = sachip->base + SA1111_GPIO;
#define MODIFY_BITS(port, mask, dir) \
if (mask) { \
val = sa1111_readl(port); \
val &= ~(mask); \
val |= (dir) & (mask); \
sa1111_writel(val, port); \
}
spin_lock_irqsave(&sachip->lock, flags);
MODIFY_BITS(gpio + SA1111_GPIO_PADDR, bits & 15, dir);
MODIFY_BITS(gpio + SA1111_GPIO_PBDDR, (bits >> 8) & 255, dir >> 8);
MODIFY_BITS(gpio + SA1111_GPIO_PCDDR, (bits >> 16) & 255, dir >> 16);
MODIFY_BITS(gpio + SA1111_GPIO_PASDR, bits & 15, sleep_dir);
MODIFY_BITS(gpio + SA1111_GPIO_PBSDR, (bits >> 8) & 255, sleep_dir >> 8);
MODIFY_BITS(gpio + SA1111_GPIO_PCSDR, (bits >> 16) & 255, sleep_dir >> 16);
spin_unlock_irqrestore(&sachip->lock, flags);
}
EXPORT_SYMBOL(sa1111_set_io_dir);
void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned long flags;
unsigned int val;
void __iomem *gpio = sachip->base + SA1111_GPIO;
spin_lock_irqsave(&sachip->lock, flags);
MODIFY_BITS(gpio + SA1111_GPIO_PADWR, bits & 15, v);
MODIFY_BITS(gpio + SA1111_GPIO_PBDWR, (bits >> 8) & 255, v >> 8);
MODIFY_BITS(gpio + SA1111_GPIO_PCDWR, (bits >> 16) & 255, v >> 16);
spin_unlock_irqrestore(&sachip->lock, flags);
}
EXPORT_SYMBOL(sa1111_set_io);
void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned long flags;
unsigned int val;
void __iomem *gpio = sachip->base + SA1111_GPIO;
spin_lock_irqsave(&sachip->lock, flags);
MODIFY_BITS(gpio + SA1111_GPIO_PASSR, bits & 15, v);
MODIFY_BITS(gpio + SA1111_GPIO_PBSSR, (bits >> 8) & 255, v >> 8);
MODIFY_BITS(gpio + SA1111_GPIO_PCSSR, (bits >> 16) & 255, v >> 16);
spin_unlock_irqrestore(&sachip->lock, flags);
}
EXPORT_SYMBOL(sa1111_set_sleep_io);
/*
* Individual device operations.
*/
/**
* sa1111_enable_device - enable an on-chip SA1111 function block
* @sadev: SA1111 function block device to enable
*/
void sa1111_enable_device(struct sa1111_dev *sadev)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned long flags;
unsigned int val;
spin_lock_irqsave(&sachip->lock, flags);
val = sa1111_readl(sachip->base + SA1111_SKPCR);
sa1111_writel(val | sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
spin_unlock_irqrestore(&sachip->lock, flags);
}
EXPORT_SYMBOL(sa1111_enable_device);
/**
* sa1111_disable_device - disable an on-chip SA1111 function block
* @sadev: SA1111 function block device to disable
*/
void sa1111_disable_device(struct sa1111_dev *sadev)
{
struct sa1111 *sachip = sa1111_chip_driver(sadev);
unsigned long flags;
unsigned int val;
spin_lock_irqsave(&sachip->lock, flags);
val = sa1111_readl(sachip->base + SA1111_SKPCR);
sa1111_writel(val & ~sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
spin_unlock_irqrestore(&sachip->lock, flags);
}
EXPORT_SYMBOL(sa1111_disable_device);
/*
* SA1111 "Register Access Bus."
*
* We model this as a regular bus type, and hang devices directly
* off this.
*/
static int sa1111_match(struct device *_dev, struct device_driver *_drv)
{
struct sa1111_dev *dev = SA1111_DEV(_dev);
struct sa1111_driver *drv = SA1111_DRV(_drv);
return dev->devid == drv->devid;
}
static int sa1111_bus_suspend(struct device *dev, pm_message_t state)
{
struct sa1111_dev *sadev = SA1111_DEV(dev);
struct sa1111_driver *drv = SA1111_DRV(dev->driver);
int ret = 0;
if (drv && drv->suspend)
ret = drv->suspend(sadev, state);
return ret;
}
static int sa1111_bus_resume(struct device *dev)
{
struct sa1111_dev *sadev = SA1111_DEV(dev);
struct sa1111_driver *drv = SA1111_DRV(dev->driver);
int ret = 0;
if (drv && drv->resume)
ret = drv->resume(sadev);
return ret;
}
static int sa1111_bus_probe(struct device *dev)
{
struct sa1111_dev *sadev = SA1111_DEV(dev);
struct sa1111_driver *drv = SA1111_DRV(dev->driver);
int ret = -ENODEV;
if (drv->probe)
ret = drv->probe(sadev);
return ret;
}
static int sa1111_bus_remove(struct device *dev)
{
struct sa1111_dev *sadev = SA1111_DEV(dev);
struct sa1111_driver *drv = SA1111_DRV(dev->driver);
int ret = 0;
if (drv->remove)
ret = drv->remove(sadev);
return ret;
}
struct bus_type sa1111_bus_type = {
.name = "sa1111-rab",
.match = sa1111_match,
.probe = sa1111_bus_probe,
.remove = sa1111_bus_remove,
.suspend = sa1111_bus_suspend,
.resume = sa1111_bus_resume,
};
EXPORT_SYMBOL(sa1111_bus_type);
int sa1111_driver_register(struct sa1111_driver *driver)
{
driver->drv.bus = &sa1111_bus_type;
return driver_register(&driver->drv);
}
EXPORT_SYMBOL(sa1111_driver_register);
void sa1111_driver_unregister(struct sa1111_driver *driver)
{
driver_unregister(&driver->drv);
}
EXPORT_SYMBOL(sa1111_driver_unregister);
static int __init sa1111_init(void)
{
int ret = bus_register(&sa1111_bus_type);
if (ret == 0)
platform_driver_register(&sa1111_device_driver);
return ret;
}
static void __exit sa1111_exit(void)
{
platform_driver_unregister(&sa1111_device_driver);
bus_unregister(&sa1111_bus_type);
}
subsys_initcall(sa1111_init);
module_exit(sa1111_exit);
MODULE_DESCRIPTION("Intel Corporation SA1111 core driver");
MODULE_LICENSE("GPL");