1. 根目录:
2. arch
3. arm
4. mach-orion5x
5. terastation_pro2-setup.c

/*
 * Buffalo Terastation Pro II/Live Board Setup
 *
 * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version
 * 2 of the License, or (at your option) any later version.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"

/*****************************************************************************
 * Terastation Pro 2/Live Info
 ****************************************************************************/

/*
 * Terastation Pro 2 hardware :
 * - Marvell 88F5281-D0
 * - Marvell 88SX6042 SATA controller (PCI)
 * - Marvell 88E1118 Gigabit Ethernet PHY
 * - 256KB NOR flash
 * - 128MB of DDR RAM
 * - PCIe port (not equipped)
 */

/*
 * 256K NOR flash Device bus boot chip select
 */

#define TSP2_NOR_BOOT_BASE	0xf4000000
#define TSP2_NOR_BOOT_SIZE	SZ_256K

/*****************************************************************************
 * 256KB NOR Flash on BOOT Device
 ****************************************************************************/

static struct physmap_flash_data tsp2_nor_flash_data = {
	.width    = 1,
};

static struct resource tsp2_nor_flash_resource = {
	.flags = IORESOURCE_MEM,
	.start = TSP2_NOR_BOOT_BASE,
	.end   = TSP2_NOR_BOOT_BASE + TSP2_NOR_BOOT_SIZE - 1,
};

static struct platform_device tsp2_nor_flash = {
	.name          = "physmap-flash",
	.id            = 0,
	.dev           = {
		.platform_data	= &tsp2_nor_flash_data,
	},
	.num_resources = 1,
	.resource      = &tsp2_nor_flash_resource,
};

/*****************************************************************************
 * PCI
 ****************************************************************************/
#define TSP2_PCI_SLOT0_OFFS		7
#define TSP2_PCI_SLOT0_IRQ_PIN		11

void __init tsp2_pci_preinit(void)
{
	int pin;

	/*
	 * Configure PCI GPIO IRQ pins
	 */
	pin = TSP2_PCI_SLOT0_IRQ_PIN;
	if (gpio_request(pin, "PCI Int1") == 0) {
		if (gpio_direction_input(pin) == 0) {
			irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
		} else {
			printk(KERN_ERR "tsp2_pci_preinit failed "
					"to set_irq_type pin %d\n", pin);
			gpio_free(pin);
		}
	} else {
		printk(KERN_ERR "tsp2_pci_preinit failed to "
				"gpio_request %d\n", pin);
	}
}

static int __init tsp2_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
{
	int irq;

	/*
	 * Check for devices with hard-wired IRQs.
	 */
	irq = orion5x_pci_map_irq(dev, slot, pin);
	if (irq != -1)
		return irq;

	/*
	 * PCI IRQs are connected via GPIOs.
	 */
	if (slot == TSP2_PCI_SLOT0_OFFS)
		return gpio_to_irq(TSP2_PCI_SLOT0_IRQ_PIN);

	return -1;
}

static struct hw_pci tsp2_pci __initdata = {
	.nr_controllers = 2,
	.preinit        = tsp2_pci_preinit,
	.swizzle        = pci_std_swizzle,
	.setup          = orion5x_pci_sys_setup,
	.scan           = orion5x_pci_sys_scan_bus,
	.map_irq        = tsp2_pci_map_irq,
};

static int __init tsp2_pci_init(void)
{
	if (machine_is_terastation_pro2())
		pci_common_init(&tsp2_pci);

	return 0;
}

subsys_initcall(tsp2_pci_init);

/*****************************************************************************
 * Ethernet
 ****************************************************************************/

static struct mv643xx_eth_platform_data tsp2_eth_data = {
	.phy_addr	= 0,
};

/*****************************************************************************
 * RTC 5C372a on I2C bus
 ****************************************************************************/

#define TSP2_RTC_GPIO	9

static struct i2c_board_info __initdata tsp2_i2c_rtc = {
	I2C_BOARD_INFO("rs5c372a", 0x32),
};

/*****************************************************************************
 * Terastation Pro II specific power off method via UART1-attached
 * microcontroller
 ****************************************************************************/

#define UART1_REG(x)	(UART1_VIRT_BASE + ((UART_##x) << 2))

static int tsp2_miconread(unsigned char *buf, int count)
{
	int i;
	int timeout;

	for (i = 0; i < count; i++) {
		timeout = 10;

		while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) {
			if (--timeout == 0)
				break;
			udelay(1000);
		}

		if (timeout == 0)
			break;
		buf[i] = readl(UART1_REG(RX));
	}

	/* return read bytes */
	return i;
}

static int tsp2_miconwrite(const unsigned char *buf, int count)
{
	int i = 0;

	while (count--) {
		while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE))
			barrier();
		writel(buf[i++], UART1_REG(TX));
	}

	return 0;
}

static int tsp2_miconsend(const unsigned char *data, int count)
{
	int i;
	unsigned char checksum = 0;
	unsigned char recv_buf[40];
	unsigned char send_buf[40];
	unsigned char correct_ack[3];
	int retry = 2;

	/* Generate checksum */
	for (i = 0; i < count; i++)
		checksum -=  data[i];

	do {
		/* Send data */
		tsp2_miconwrite(data, count);

		/* send checksum */
		tsp2_miconwrite(&checksum, 1);

		if (tsp2_miconread(recv_buf, sizeof(recv_buf)) <= 3) {
			printk(KERN_ERR ">%s: receive failed.\n", __func__);

			/* send preamble to clear the receive buffer */
			memset(&send_buf, 0xff, sizeof(send_buf));
			tsp2_miconwrite(send_buf, sizeof(send_buf));

			/* make dummy reads */
			mdelay(100);
			tsp2_miconread(recv_buf, sizeof(recv_buf));
		} else {
			/* Generate expected ack */
			correct_ack[0] = 0x01;
			correct_ack[1] = data[1];
			correct_ack[2] = 0x00;

			/* checksum Check */
			if ((recv_buf[0] + recv_buf[1] + recv_buf[2] +
			     recv_buf[3]) & 0xFF) {
				printk(KERN_ERR ">%s: Checksum Error : "
					"Received data[%02x, %02x, %02x, %02x]"
					"\n", __func__, recv_buf[0],
					recv_buf[1], recv_buf[2], recv_buf[3]);
			} else {
				/* Check Received Data */
				if (correct_ack[0] == recv_buf[0] &&
				    correct_ack[1] == recv_buf[1] &&
				    correct_ack[2] == recv_buf[2]) {
					/* Interval for next command */
					mdelay(10);

					/* Receive ACK */
					return 0;
				}
			}
			/* Received NAK or illegal Data */
			printk(KERN_ERR ">%s: Error : NAK or Illegal Data "
					"Received\n", __func__);
		}
	} while (retry--);

	/* Interval for next command */
	mdelay(10);

	return -1;
}

static void tsp2_power_off(void)
{
	const unsigned char watchdogkill[]	= {0x01, 0x35, 0x00};
	const unsigned char shutdownwait[]	= {0x00, 0x0c};
	const unsigned char poweroff[]		= {0x00, 0x06};
	/* 38400 baud divisor */
	const unsigned divisor = ((orion5x_tclk + (8 * 38400)) / (16 * 38400));

	pr_info("%s: triggering power-off...\n", __func__);

	/* hijack uart1 and reset into sane state (38400,8n1,even parity) */
	writel(0x83, UART1_REG(LCR));
	writel(divisor & 0xff, UART1_REG(DLL));
	writel((divisor >> 8) & 0xff, UART1_REG(DLM));
	writel(0x1b, UART1_REG(LCR));
	writel(0x00, UART1_REG(IER));
	writel(0x07, UART1_REG(FCR));
	writel(0x00, UART1_REG(MCR));

	/* Send the commands to shutdown the Terastation Pro II */
	tsp2_miconsend(watchdogkill, sizeof(watchdogkill)) ;
	tsp2_miconsend(shutdownwait, sizeof(shutdownwait)) ;
	tsp2_miconsend(poweroff, sizeof(poweroff));
}

/*****************************************************************************
 * General Setup
 ****************************************************************************/
static struct orion5x_mpp_mode tsp2_mpp_modes[] __initdata = {
	{  0, MPP_PCIE_RST_OUTn },
	{  1, MPP_UNUSED },
	{  2, MPP_UNUSED },
	{  3, MPP_UNUSED },
	{  4, MPP_NAND },		/* BOOT NAND Flash REn */
	{  5, MPP_NAND },		/* BOOT NAND Flash WEn */
	{  6, MPP_NAND },		/* BOOT NAND Flash HREn[0] */
	{  7, MPP_NAND },		/* BOOT NAND Flash WEn[0] */
	{  8, MPP_GPIO },		/* MICON int */
	{  9, MPP_GPIO },		/* RTC int */
	{ 10, MPP_UNUSED },
	{ 11, MPP_GPIO },		/* PCI Int A */
	{ 12, MPP_UNUSED },
	{ 13, MPP_GPIO },		/* UPS on UART0 enable */
	{ 14, MPP_GPIO },		/* UPS low battery detection */
	{ 15, MPP_UNUSED },
	{ 16, MPP_UART },		/* UART1 RXD */
	{ 17, MPP_UART },		/* UART1 TXD */
	{ 18, MPP_UART },		/* UART1 CTSn */
	{ 19, MPP_UART },		/* UART1 RTSn */
	{ -1 },
};

static void __init tsp2_init(void)
{
	/*
	 * Setup basic Orion functions. Need to be called early.
	 */
	orion5x_init();

	orion5x_mpp_conf(tsp2_mpp_modes);

	/*
	 * Configure peripherals.
	 */
	orion5x_setup_dev_boot_win(TSP2_NOR_BOOT_BASE,
				   TSP2_NOR_BOOT_SIZE);
	platform_device_register(&tsp2_nor_flash);

	orion5x_ehci0_init();
	orion5x_eth_init(&tsp2_eth_data);
	orion5x_i2c_init();
	orion5x_uart0_init();
	orion5x_uart1_init();

	/* Get RTC IRQ and register the chip */
	if (gpio_request(TSP2_RTC_GPIO, "rtc") == 0) {
		if (gpio_direction_input(TSP2_RTC_GPIO) == 0)
			tsp2_i2c_rtc.irq = gpio_to_irq(TSP2_RTC_GPIO);
		else
			gpio_free(TSP2_RTC_GPIO);
	}
	if (tsp2_i2c_rtc.irq == 0)
		pr_warning("tsp2_init: failed to get RTC IRQ\n");
	i2c_register_board_info(0, &tsp2_i2c_rtc, 1);

	/* register Terastation Pro II specific power-off method */
	pm_power_off = tsp2_power_off;
}

MACHINE_START(TERASTATION_PRO2, "Buffalo Terastation Pro II/Live")
	/* Maintainer:  Sylver Bruneau <sylver.bruneau@googlemail.com> */
	.boot_params	= 0x00000100,
	.init_machine	= tsp2_init,
	.map_io		= orion5x_map_io,
	.init_early	= orion5x_init_early,
	.init_irq	= orion5x_init_irq,
	.timer		= &orion5x_timer,
	.fixup		= tag_fixup_mem32,
MACHINE_END