config ATH6K_LEGACY
	tristate "Atheros AR6003 support (non mac80211)"
        depends on MMC && WLAN
	depends on CFG80211
        select WIRELESS_EXT
        select WEXT_PRIV
	help
	This module adds support for wireless adapters based on Atheros AR6003 chipset running over SDIO. If you choose to build it as a module, it will be called ath6kl. Pls note that AR6002 and AR6001 are not supported by this driver.

choice
	prompt "AR6003 Board Data Configuration"
	depends on ATH6K_LEGACY
	default AR600x_SD31_XXX
	help
	Select the appropriate board data template from the list below that matches your AR6003 based reference design.

config AR600x_SD31_XXX
	bool "SD31-xxx"
	help
        Board Data file for a standard SD31 reference design (File: bdata.SD31.bin)

config AR600x_WB31_XXX
	bool "WB31-xxx"
	help
        Board Data file for a standard WB31 (BT/WiFi) reference design (File: bdata.WB31.bin)

config AR600x_SD32_XXX
	bool "SD32-xxx"
	help
        Board Data file for a standard SD32 (5GHz) reference design (File: bdata.SD32.bin)

config AR600x_CUSTOM_XXX
	bool "CUSTOM-xxx"
	help
        Board Data file for a custom reference design (File: should be named as bdata.CUSTOM.bin)
endchoice

config ATH6KL_ENABLE_COEXISTENCE
	bool "BT Coexistence support"
	depends on ATH6K_LEGACY
	help
	Enables WLAN/BT coexistence support. Select the apprpriate configuration from below.

choice
	prompt "Front-End Antenna Configuration"
	depends on ATH6KL_ENABLE_COEXISTENCE
	default AR600x_DUAL_ANTENNA
	help
	Indicates the number of antennas being used by BT and WLAN. Select the appropriate configuration from the list below that matches your AR6003 based reference design.

config AR600x_DUAL_ANTENNA
	bool "Dual Antenna"
	help
        Dual Antenna Design

config AR600x_SINGLE_ANTENNA
	bool "Single Antenna"
	help
        Single Antenna Design
endchoice

choice
	prompt "Collocated Bluetooth Type"
	depends on ATH6KL_ENABLE_COEXISTENCE
	default AR600x_BT_AR3001
	help
	Select the appropriate configuration from the list below that matches your AR6003 based reference design.

config AR600x_BT_QCOM
	bool "Qualcomm BTS4020X"
	help
        Qualcomm BT (3 Wire PTA)

config AR600x_BT_CSR
	bool "CSR BC06"
	help
        CSR BT (3 Wire PTA)

config AR600x_BT_AR3001
	bool "Atheros AR3001"
	help
        Atheros BT (3 Wire PTA)
endchoice

config ATH6KL_HCI_BRIDGE
	bool "HCI over SDIO support"
	depends on ATH6K_LEGACY
	help
	Enables BT over SDIO. Applicable only for combo designs (eg: WB31)

config ATH6KL_CONFIG_GPIO_BT_RESET
	bool "Configure BT Reset GPIO"
	depends on ATH6KL_HCI_BRIDGE
	help
	Configure a WLAN GPIO for use with BT.

config AR600x_BT_RESET_PIN
	int "GPIO"
	depends on ATH6KL_CONFIG_GPIO_BT_RESET
	default 22
	help
	WLAN GPIO to be used for resetting BT

config ATH6KL_HTC_RAW_INTERFACE
	bool "RAW HTC support"
	depends on ATH6K_LEGACY
	help
	Enables raw HTC interface. Allows application to directly talk to the HTC interface via the ioctl interface

config ATH6KL_VIRTUAL_SCATTER_GATHER
	bool "Virtual Scatter-Gather support"
	depends on ATH6K_LEGACY
	help
	Enables virtual scatter gather support for the hardware that does not support it natively.

config ATH6KL_SKIP_ABI_VERSION_CHECK
	bool "Skip ABI version check support"
	depends on ATH6K_LEGACY
	help
	Forces the driver to disable ABI version check. Caution: Incompatilbity between the host driver and target firmware may lead to unknown side effects.

config ATH6KL_BT_UART_FC_POLARITY
	int "UART Flow Control Polarity"
	depends on ATH6KL_LEGACY
	default 0
	help
	Configures the polarity of UART Flow Control. A value of 0 implies active low and is the default setting. Set it to 1 for active high.

config ATH6KL_DEBUG
	bool "Debug support"
	depends on ATH6K_LEGACY
	help
	Enables debug support

config ATH6KL_ENABLE_HOST_DEBUG
	bool "Host Debug support"
	depends on ATH6KL_DEBUG
	help
	Enables debug support in the driver

config ATH6KL_ENABLE_TARGET_DEBUG_PRINTS
	bool "Target Debug support - Enable UART prints"
	depends on ATH6KL_DEBUG
	help
	Enables uart prints

config AR600x_DEBUG_UART_TX_PIN
	int "GPIO"
	depends on ATH6KL_ENABLE_TARGET_DEBUG_PRINTS
	default 8
	help
	WLAN GPIO to be used for Debug UART (Tx)

config ATH6KL_DISABLE_TARGET_DBGLOGS
	bool "Target Debug support - Disable Debug logs"
	depends on ATH6KL_DEBUG
	help
	Enables debug logs