/* dp83640_reg.h * Generated by regen.tcl on Thu Feb 17 10:02:48 AM CET 2011 */ #ifndef HAVE_DP83640_REGISTERS #define HAVE_DP83640_REGISTERS #define PAGE0 0x0000 #define PHYCR2 0x001c /* PHY Control Register 2 */ #define PAGE4 0x0004 #define PTP_CTL 0x0014 /* PTP Control Register */ #define PTP_TDR 0x0015 /* PTP Time Data Register */ #define PTP_STS 0x0016 /* PTP Status Register */ #define PTP_TSTS 0x0017 /* PTP Trigger Status Register */ #define PTP_RATEL 0x0018 /* PTP Rate Low Register */ #define PTP_RATEH 0x0019 /* PTP Rate High Register */ #define PTP_RDCKSUM 0x001a /* PTP Read Checksum */ #define PTP_WRCKSUM 0x001b /* PTP Write Checksum */ #define PTP_TXTS 0x001c /* PTP Transmit Timestamp Register, in four 16-bit reads */ #define PTP_RXTS 0x001d /* PTP Receive Timestamp Register, in six? 16-bit reads */ #define PTP_ESTS 0x001e /* PTP Event Status Register */ #define PTP_EDATA 0x001f /* PTP Event Data Register */ #define PAGE5 0x0005 #define PTP_TRIG 0x0014 /* PTP Trigger Configuration Register */ #define PTP_EVNT 0x0015 /* PTP Event Configuration Register */ #define PTP_TXCFG0 0x0016 /* PTP Transmit Configuration Register 0 */ #define PTP_TXCFG1 0x0017 /* PTP Transmit Configuration Register 1 */ #define PSF_CFG0 0x0018 /* PHY Status Frame Configuration Register 0 */ #define PTP_RXCFG0 0x0019 /* PTP Receive Configuration Register 0 */ #define PTP_RXCFG1 0x001a /* PTP Receive Configuration Register 1 */ #define PTP_RXCFG2 0x001b /* PTP Receive Configuration Register 2 */ #define PTP_RXCFG3 0x001c /* PTP Receive Configuration Register 3 */ #define PTP_RXCFG4 0x001d /* PTP Receive Configuration Register 4 */ #define PTP_TRDL 0x001e /* PTP Temporary Rate Duration Low Register */ #define PTP_TRDH 0x001f /* PTP Temporary Rate Duration High Register */ #define PAGE6 0x0006 #define PTP_COC 0x0014 /* PTP Clock Output Control Register */ #define PSF_CFG1 0x0015 /* PHY Status Frame Configuration Register 1 */ #define PSF_CFG2 0x0016 /* PHY Status Frame Configuration Register 2 */ #define PSF_CFG3 0x0017 /* PHY Status Frame Configuration Register 3 */ #define PSF_CFG4 0x0018 /* PHY Status Frame Configuration Register 4 */ #define PTP_SFDCFG 0x0019 /* PTP SFD Configuration Register */ #define PTP_INTCTL 0x001a /* PTP Interrupt Control Register */ #define PTP_CLKSRC 0x001b /* PTP Clock Source Register */ #define PTP_ETR 0x001c /* PTP Ethernet Type Register */ #define PTP_OFF 0x001d /* PTP Offset Register */ #define PTP_GPIOMON 0x001e /* PTP GPIO Monitor Register */ #define PTP_RXHASH 0x001f /* PTP Receive Hash Register */ /* Bit definitions for the PHYCR2 register */ #define BC_WRITE (1<<11) /* Broadcast Write Enable */ /* Bit definitions for the PTP_CTL register */ #define TRIG_SEL_SHIFT (10) /* PTP Trigger Select */ #define TRIG_SEL_MASK (0x7) #define TRIG_DIS (1<<9) /* Disable PTP Trigger */ #define TRIG_EN (1<<8) /* Enable PTP Trigger */ #define TRIG_READ (1<<7) /* Read PTP Trigger */ #define TRIG_LOAD (1<<6) /* Load PTP Trigger */ #define PTP_RD_CLK (1<<5) /* Read PTP Clock */ #define PTP_LOAD_CLK (1<<4) /* Load PTP Clock */ #define PTP_STEP_CLK (1<<3) /* Step PTP Clock */ #define PTP_ENABLE (1<<2) /* Enable PTP Clock */ #define PTP_DISABLE (1<<1) /* Disable PTP Clock */ #define PTP_RESET (1<<0) /* Reset PTP Clock */ /* Bit definitions for the PTP_STS register */ #define TXTS_RDY (1<<11) /* Transmit Timestamp Ready */ #define RXTS_RDY (1<<10) /* Receive Timestamp Ready */ #define TRIG_DONE (1<<9) /* PTP Trigger Done */ #define EVENT_RDY (1<<8) /* PTP Event Timestamp Ready */ #define TXTS_IE (1<<3) /* Transmit Timestamp Interrupt Enable */ #define RXTS_IE (1<<2) /* Receive Timestamp Interrupt Enable */ #define TRIG_IE (1<<1) /* Trigger Interrupt Enable */ #define EVENT_IE (1<<0) /* Event Interrupt Enable */ /* Bit definitions for the PTP_TSTS register */ #define TRIG7_ERROR (1<<15) /* Trigger 7 Error */ #define TRIG7_ACTIVE (1<<14) /* Trigger 7 Active */ #define TRIG6_ERROR (1<<13) /* Trigger 6 Error */ #define TRIG6_ACTIVE (1<<12) /* Trigger 6 Active */ #define TRIG5_ERROR (1<<11) /* Trigger 5 Error */ #define TRIG5_ACTIVE (1<<10) /* Trigger 5 Active */ #define TRIG4_ERROR (1<<9) /* Trigger 4 Error */ #define TRIG4_ACTIVE (1<<8) /* Trigger 4 Active */ #define TRIG3_ERROR (1<<7) /* Trigger 3 Error */ #define TRIG3_ACTIVE (1<<6) /* Trigger 3 Active */ #define TRIG2_ERROR (1<<5) /* Trigger 2 Error */ #define TRIG2_ACTIVE (1<<4) /* Trigger 2 Active */ #define TRIG1_ERROR (1<<3) /* Trigger 1 Error */ #define TRIG1_ACTIVE (1<<2) /* Trigger 1 Active */ #define TRIG0_ERROR (1<<1) /* Trigger 0 Error */ #define TRIG0_ACTIVE (1<<0) /* Trigger 0 Active */ /* Bit definitions for the PTP_RATEH register */ #define PTP_RATE_DIR (1<<15) /* PTP Rate Direction */ #define PTP_TMP_RATE (1<<14) /* PTP Temporary Rate */ #define PTP_RATE_HI_SHIFT (0) /* PTP Rate High 10-bits */ #define PTP_RATE_HI_MASK (0x3ff) /* Bit definitions for the PTP_ESTS register */ #define EVNTS_MISSED_SHIFT (8) /* Indicates number of events missed */ #define EVNTS_MISSED_MASK (0x7) #define EVNT_TS_LEN_SHIFT (6) /* Indicates length of the Timestamp field in 16-bit words minus 1 */ #define EVNT_TS_LEN_MASK (0x3) #define EVNT_RF (1<<5) /* Indicates whether the event is a rise or falling event */ #define EVNT_NUM_SHIFT (2) /* Indicates Event Timestamp Unit which detected an event */ #define EVNT_NUM_MASK (0x7) #define MULT_EVNT (1<<1) /* Indicates multiple events were detected at the same time */ #define EVENT_DET (1<<0) /* PTP Event Detected */ /* Bit definitions for the PTP_EDATA register */ #define E7_RISE (1<<15) /* Indicates direction of Event 7 */ #define E7_DET (1<<14) /* Indicates Event 7 detected */ #define E6_RISE (1<<13) /* Indicates direction of Event 6 */ #define E6_DET (1<<12) /* Indicates Event 6 detected */ #define E5_RISE (1<<11) /* Indicates direction of Event 5 */ #define E5_DET (1<<10) /* Indicates Event 5 detected */ #define E4_RISE (1<<9) /* Indicates direction of Event 4 */ #define E4_DET (1<<8) /* Indicates Event 4 detected */ #define E3_RISE (1<<7) /* Indicates direction of Event 3 */ #define E3_DET (1<<6) /* Indicates Event 3 detected */ #define E2_RISE (1<<5) /* Indicates direction of Event 2 */ #define E2_DET (1<<4) /* Indicates Event 2 detected */ #define E1_RISE (1<<3) /* Indicates direction of Event 1 */ #define E1_DET (1<<2) /* Indicates Event 1 detected */ #define E0_RISE (1<<1) /* Indicates direction of Event 0 */ #define E0_DET (1<<0) /* Indicates Event 0 detected */ /* Bit definitions for the PTP_TRIG register */ #define TRIG_PULSE (1<<15) /* generate a Pulse rather than a single edge */ #define TRIG_PER (1<<14) /* generate a periodic signal */ #define TRIG_IF_LATE (1<<13) /* trigger immediately if already past */ #define TRIG_NOTIFY (1<<12) /* Trigger Notification Enable */ #define TRIG_GPIO_SHIFT (8) /* Trigger GPIO Connection, value 1-12 */ #define TRIG_GPIO_MASK (0xf) #define TRIG_TOGGLE (1<<7) /* Trigger Toggle Mode Enable */ #define TRIG_CSEL_SHIFT (1) /* Trigger Configuration Select */ #define TRIG_CSEL_MASK (0x7) #define TRIG_WR (1<<0) /* Trigger Configuration Write */ /* Bit definitions for the PTP_EVNT register */ #define EVNT_RISE (1<<14) /* Event Rise Detect Enable */ #define EVNT_FALL (1<<13) /* Event Fall Detect Enable */ #define EVNT_SINGLE (1<<12) /* enable single event capture operation */ #define EVNT_GPIO_SHIFT (8) /* Event GPIO Connection, value 1-12 */ #define EVNT_GPIO_MASK (0xf) #define EVNT_SEL_SHIFT (1) /* Event Select */ #define EVNT_SEL_MASK (0x7) #define EVNT_WR (1<<0) /* Event Configuration Write */ /* Bit definitions for the PTP_TXCFG0 register */ #define SYNC_1STEP (1<<15) /* insert timestamp into transmit Sync Messages */ #define DR_INSERT (1<<13) /* Insert Delay_Req Timestamp in Delay_Resp (dangerous) */ #define NTP_TS_EN (1<<12) /* Enable Timestamping of NTP Packets */ #define IGNORE_2STEP (1<<11) /* Ignore Two_Step flag for One-Step operation */ #define CRC_1STEP (1<<10) /* Disable checking of CRC for One-Step operation */ #define CHK_1STEP (1<<9) /* Enable UDP Checksum correction for One-Step Operation */ #define IP1588_EN (1<<8) /* Enable IEEE 1588 defined IP address filter */ #define TX_L2_EN (1<<7) /* Layer2 Timestamp Enable */ #define TX_IPV6_EN (1<<6) /* IPv6 Timestamp Enable */ #define TX_IPV4_EN (1<<5) /* IPv4 Timestamp Enable */ #define TX_PTP_VER_SHIFT (1) /* Enable Timestamp capture for IEEE 1588 version X */ #define TX_PTP_VER_MASK (0xf) #define TX_TS_EN (1<<0) /* Transmit Timestamp Enable */ /* Bit definitions for the PTP_TXCFG1 register */ #define BYTE0_MASK_SHIFT (8) /* Bit mask to be used for matching Byte0 of the PTP Message */ #define BYTE0_MASK_MASK (0xff) #define BYTE0_DATA_SHIFT (0) /* Data to be used for matching Byte0 of the PTP Message */ #define BYTE0_DATA_MASK (0xff) /* Bit definitions for the PSF_CFG0 register */ #define MAC_SRC_ADD_SHIFT (11) /* Status Frame Mac Source Address */ #define MAC_SRC_ADD_MASK (0x3) #define MIN_PRE_SHIFT (8) /* Status Frame Minimum Preamble */ #define MIN_PRE_MASK (0x7) #define PSF_ENDIAN (1<<7) /* Status Frame Endian Control */ #define PSF_IPV4 (1<<6) /* Status Frame IPv4 Enable */ #define PSF_PCF_RD (1<<5) /* Control Frame Read PHY Status Frame Enable */ #define PSF_ERR_EN (1<<4) /* Error PHY Status Frame Enable */ #define PSF_TXTS_EN (1<<3) /* Transmit Timestamp PHY Status Frame Enable */ #define PSF_RXTS_EN (1<<2) /* Receive Timestamp PHY Status Frame Enable */ #define PSF_TRIG_EN (1<<1) /* Trigger PHY Status Frame Enable */ #define PSF_EVNT_EN (1<<0) /* Event PHY Status Frame Enable */ /* Bit definitions for the PTP_RXCFG0 register */ #define DOMAIN_EN (1<<15) /* Domain Match Enable */ #define ALT_MAST_DIS (1<<14) /* Alternate Master Timestamp Disable */ #define USER_IP_SEL (1<<13) /* Selects portion of IP address accessible thru PTP_RXCFG2 */ #define USER_IP_EN (1<<12) /* Enable User-programmed IP address filter */ #define RX_SLAVE (1<<11) /* Receive Slave Only */ #define IP1588_EN_SHIFT (8) /* Enable IEEE 1588 defined IP address filters */ #define IP1588_EN_MASK (0xf) #define RX_L2_EN (1<<7) /* Layer2 Timestamp Enable */ #define RX_IPV6_EN (1<<6) /* IPv6 Timestamp Enable */ #define RX_IPV4_EN (1<<5) /* IPv4 Timestamp Enable */ #define RX_PTP_VER_SHIFT (1) /* Enable Timestamp capture for IEEE 1588 version X */ #define RX_PTP_VER_MASK (0xf) #define RX_TS_EN (1<<0) /* Receive Timestamp Enable */ /* Bit definitions for the PTP_RXCFG1 register */ #define BYTE0_MASK_SHIFT (8) /* Bit mask to be used for matching Byte0 of the PTP Message */ #define BYTE0_MASK_MASK (0xff) #define BYTE0_DATA_SHIFT (0) /* Data to be used for matching Byte0 of the PTP Message */ #define BYTE0_DATA_MASK (0xff) /* Bit definitions for the PTP_RXCFG3 register */ #define TS_MIN_IFG_SHIFT (12) /* Minimum Inter-frame Gap */ #define TS_MIN_IFG_MASK (0xf) #define ACC_UDP (1<<11) /* Record Timestamp if UDP Checksum Error */ #define ACC_CRC (1<<10) /* Record Timestamp if CRC Error */ #define TS_APPEND (1<<9) /* Append Timestamp for L2 */ #define TS_INSERT (1<<8) /* Enable Timestamp Insertion */ #define PTP_DOMAIN_SHIFT (0) /* PTP Message domainNumber field */ #define PTP_DOMAIN_MASK (0xff) /* Bit definitions for the PTP_RXCFG4 register */ #define IPV4_UDP_MOD (1<<15) /* Enable IPV4 UDP Modification */ #define TS_SEC_EN (1<<14) /* Enable Timestamp Seconds */ #define TS_SEC_LEN_SHIFT (12) /* Inserted Timestamp Seconds Length */ #define TS_SEC_LEN_MASK (0x3) #define RXTS_NS_OFF_SHIFT (6) /* Receive Timestamp Nanoseconds offset */ #define RXTS_NS_OFF_MASK (0x3f) #define RXTS_SEC_OFF_SHIFT (0) /* Receive Timestamp Seconds offset */ #define RXTS_SEC_OFF_MASK (0x3f) /* Bit definitions for the PTP_COC register */ #define PTP_CLKOUT_EN (1<<15) /* PTP Clock Output Enable */ #define PTP_CLKOUT_SEL (1<<14) /* PTP Clock Output Source Select */ #define PTP_CLKOUT_SPEEDSEL (1<<13) /* PTP Clock Output I/O Speed Select */ #define PTP_CLKDIV_SHIFT (0) /* PTP Clock Divide-by Value */ #define PTP_CLKDIV_MASK (0xff) /* Bit definitions for the PSF_CFG1 register */ #define PTPRESERVED_SHIFT (12) /* PTP v2 reserved field */ #define PTPRESERVED_MASK (0xf) #define VERSIONPTP_SHIFT (8) /* PTP v2 versionPTP field */ #define VERSIONPTP_MASK (0xf) #define TRANSPORT_SPECIFIC_SHIFT (4) /* PTP v2 Header transportSpecific field */ #define TRANSPORT_SPECIFIC_MASK (0xf) #define MESSAGETYPE_SHIFT (0) /* PTP v2 messageType field */ #define MESSAGETYPE_MASK (0xf) /* Bit definitions for the PTP_SFDCFG register */ #define TX_SFD_GPIO_SHIFT (4) /* TX SFD GPIO Select, value 1-12 */ #define TX_SFD_GPIO_MASK (0xf) #define RX_SFD_GPIO_SHIFT (0) /* RX SFD GPIO Select, value 1-12 */ #define RX_SFD_GPIO_MASK (0xf) /* Bit definitions for the PTP_INTCTL register */ #define PTP_INT_GPIO_SHIFT (0) /* PTP Interrupt GPIO Select */ #define PTP_INT_GPIO_MASK (0xf) /* Bit definitions for the PTP_CLKSRC register */ #define CLK_SRC_SHIFT (14) /* PTP Clock Source Select */ #define CLK_SRC_MASK (0x3) #define CLK_SRC_PER_SHIFT (0) /* PTP Clock Source Period */ #define CLK_SRC_PER_MASK (0x7f) /* Bit definitions for the PTP_OFF register */ #define PTP_OFFSET_SHIFT (0) /* PTP Message offset from preceding header */ #define PTP_OFFSET_MASK (0xff) #endif