#ifndef SPI_ADIS16240_H_
#define SPI_ADIS16240_H_

#define ADIS16240_STARTUP_DELAY	220 /* ms */

/* Flash memory write count */
#define ADIS16240_FLASH_CNT      0x00
/* Output, power supply */
#define ADIS16240_SUPPLY_OUT     0x02
/* Output, x-axis accelerometer */
#define ADIS16240_XACCL_OUT      0x04
/* Output, y-axis accelerometer */
#define ADIS16240_YACCL_OUT      0x06
/* Output, z-axis accelerometer */
#define ADIS16240_ZACCL_OUT      0x08
/* Output, auxiliary ADC input */
#define ADIS16240_AUX_ADC        0x0A
/* Output, temperature */
#define ADIS16240_TEMP_OUT       0x0C
/* Output, x-axis acceleration peak */
#define ADIS16240_XPEAK_OUT      0x0E
/* Output, y-axis acceleration peak */
#define ADIS16240_YPEAK_OUT      0x10
/* Output, z-axis acceleration peak */
#define ADIS16240_ZPEAK_OUT      0x12
/* Output, sum-of-squares acceleration peak */
#define ADIS16240_XYZPEAK_OUT    0x14
/* Output, Capture Buffer 1, X and Y acceleration */
#define ADIS16240_CAPT_BUF1      0x16
/* Output, Capture Buffer 2, Z acceleration */
#define ADIS16240_CAPT_BUF2      0x18
/* Diagnostic, error flags */
#define ADIS16240_DIAG_STAT      0x1A
/* Diagnostic, event counter */
#define ADIS16240_EVNT_CNTR      0x1C
/* Diagnostic, check sum value from firmware test */
#define ADIS16240_CHK_SUM        0x1E
/* Calibration, x-axis acceleration offset adjustment */
#define ADIS16240_XACCL_OFF      0x20
/* Calibration, y-axis acceleration offset adjustment */
#define ADIS16240_YACCL_OFF      0x22
/* Calibration, z-axis acceleration offset adjustment */
#define ADIS16240_ZACCL_OFF      0x24
/* Clock, hour and minute */
#define ADIS16240_CLK_TIME       0x2E
/* Clock, month and day */
#define ADIS16240_CLK_DATE       0x30
/* Clock, year */
#define ADIS16240_CLK_YEAR       0x32
/* Wake-up setting, hour and minute */
#define ADIS16240_WAKE_TIME      0x34
/* Wake-up setting, month and day */
#define ADIS16240_WAKE_DATE      0x36
/* Alarm 1 amplitude threshold */
#define ADIS16240_ALM_MAG1       0x38
/* Alarm 2 amplitude threshold */
#define ADIS16240_ALM_MAG2       0x3A
/* Alarm control */
#define ADIS16240_ALM_CTRL       0x3C
/* Capture, external trigger control */
#define ADIS16240_XTRIG_CTRL     0x3E
/* Capture, address pointer */
#define ADIS16240_CAPT_PNTR      0x40
/* Capture, configuration and control */
#define ADIS16240_CAPT_CTRL      0x42
/* General-purpose digital input/output control */
#define ADIS16240_GPIO_CTRL      0x44
/* Miscellaneous control */
#define ADIS16240_MSC_CTRL       0x46
/* Internal sample period (rate) control */
#define ADIS16240_SMPL_PRD       0x48
/* System command */
#define ADIS16240_GLOB_CMD       0x4A

/* MSC_CTRL */
/* Enables sum-of-squares output (XYZPEAK_OUT) */
#define ADIS16240_MSC_CTRL_XYZPEAK_OUT_EN	(1 << 15)
/* Enables peak tracking output (XPEAK_OUT, YPEAK_OUT, and ZPEAK_OUT) */
#define ADIS16240_MSC_CTRL_X_Y_ZPEAK_OUT_EN	(1 << 14)
/* Self-test enable: 1 = apply electrostatic force, 0 = disabled */
#define ADIS16240_MSC_CTRL_SELF_TEST_EN	        (1 << 8)
/* Data-ready enable: 1 = enabled, 0 = disabled */
#define ADIS16240_MSC_CTRL_DATA_RDY_EN	        (1 << 2)
/* Data-ready polarity: 1 = active high, 0 = active low */
#define ADIS16240_MSC_CTRL_ACTIVE_HIGH	        (1 << 1)
/* Data-ready line selection: 1 = DIO2, 0 = DIO1 */
#define ADIS16240_MSC_CTRL_DATA_RDY_DIO2	(1 << 0)

/* DIAG_STAT */
/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
#define ADIS16240_DIAG_STAT_ALARM2      (1<<9)
/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
#define ADIS16240_DIAG_STAT_ALARM1      (1<<8)
/* Capture buffer full: 1 = capture buffer is full */
#define ADIS16240_DIAG_STAT_CPT_BUF_FUL (1<<7)
/* Flash test, checksum flag: 1 = mismatch, 0 = match */
#define ADIS16240_DIAG_STAT_CHKSUM      (1<<6)
/* Power-on, self-test flag: 1 = failure, 0 = pass */
#define ADIS16240_DIAG_STAT_PWRON_FAIL_BIT  5
/* Power-on self-test: 1 = in-progress, 0 = complete */
#define ADIS16240_DIAG_STAT_PWRON_BUSY  (1<<4)
/* SPI communications failure */
#define ADIS16240_DIAG_STAT_SPI_FAIL_BIT	3
/* Flash update failure */
#define ADIS16240_DIAG_STAT_FLASH_UPT_BIT	2
/* Power supply above 3.625 V */
#define ADIS16240_DIAG_STAT_POWER_HIGH_BIT	1
 /* Power supply below 3.15 V */
#define ADIS16240_DIAG_STAT_POWER_LOW_BIT	0

/* GLOB_CMD */
#define ADIS16240_GLOB_CMD_RESUME	(1<<8)
#define ADIS16240_GLOB_CMD_SW_RESET	(1<<7)
#define ADIS16240_GLOB_CMD_STANDBY	(1<<2)

#define ADIS16240_ERROR_ACTIVE          (1<<14)

/* At the moment triggers are only used for ring buffer
 * filling. This may change!
 */

#define ADIS16240_SCAN_ACC_X	0
#define ADIS16240_SCAN_ACC_Y	1
#define ADIS16240_SCAN_ACC_Z	2
#define ADIS16240_SCAN_SUPPLY	3
#define ADIS16240_SCAN_AUX_ADC	4
#define ADIS16240_SCAN_TEMP	5

#endif /* SPI_ADIS16240_H_ */