- 根目录:
- arch
- mips
- cavium-octeon
- executive
- cvmx-helper-sgmii.c
/***********************license start***************
* Author: Cavium Networks
*
* Contact: support@caviumnetworks.com
* This file is part of the OCTEON SDK
*
* Copyright (c) 2003-2008 Cavium Networks
*
* This file is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License, Version 2, as
* published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful, but
* AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
* NONINFRINGEMENT. See the GNU General Public License for more
* details.
*
* You should have received a copy of the GNU General Public License
* along with this file; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
* or visit http://www.gnu.org/licenses/.
*
* This file may also be available under a different license from Cavium.
* Contact Cavium Networks for more information
***********************license end**************************************/
/*
* Functions for SGMII initialization, configuration,
* and monitoring.
*/
#include <asm/octeon/octeon.h>
#include <asm/octeon/cvmx-config.h>
#include <asm/octeon/cvmx-mdio.h>
#include <asm/octeon/cvmx-helper.h>
#include <asm/octeon/cvmx-helper-board.h>
#include <asm/octeon/cvmx-gmxx-defs.h>
#include <asm/octeon/cvmx-pcsx-defs.h>
void __cvmx_interrupt_gmxx_enable(int interface);
void __cvmx_interrupt_pcsx_intx_en_reg_enable(int index, int block);
void __cvmx_interrupt_pcsxx_int_en_reg_enable(int index);
/**
* Perform initialization required only once for an SGMII port.
*
* @interface: Interface to init
* @index: Index of prot on the interface
*
* Returns Zero on success, negative on failure
*/
static int __cvmx_helper_sgmii_hardware_init_one_time(int interface, int index)
{
const uint64_t clock_mhz = cvmx_sysinfo_get()->cpu_clock_hz / 1000000;
union cvmx_pcsx_miscx_ctl_reg pcs_misc_ctl_reg;
union cvmx_pcsx_linkx_timer_count_reg pcsx_linkx_timer_count_reg;
union cvmx_gmxx_prtx_cfg gmxx_prtx_cfg;
/* Disable GMX */
gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
gmxx_prtx_cfg.s.en = 0;
cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
/*
* Write PCS*_LINK*_TIMER_COUNT_REG[COUNT] with the
* appropriate value. 1000BASE-X specifies a 10ms
* interval. SGMII specifies a 1.6ms interval.
*/
pcs_misc_ctl_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
pcsx_linkx_timer_count_reg.u64 =
cvmx_read_csr(CVMX_PCSX_LINKX_TIMER_COUNT_REG(index, interface));
if (pcs_misc_ctl_reg.s.mode) {
/* 1000BASE-X */
pcsx_linkx_timer_count_reg.s.count =
(10000ull * clock_mhz) >> 10;
} else {
/* SGMII */
pcsx_linkx_timer_count_reg.s.count =
(1600ull * clock_mhz) >> 10;
}
cvmx_write_csr(CVMX_PCSX_LINKX_TIMER_COUNT_REG(index, interface),
pcsx_linkx_timer_count_reg.u64);
/*
* Write the advertisement register to be used as the
* tx_Config_Reg<D15:D0> of the autonegotiation. In
* 1000BASE-X mode, tx_Config_Reg<D15:D0> is PCS*_AN*_ADV_REG.
* In SGMII PHY mode, tx_Config_Reg<D15:D0> is
* PCS*_SGM*_AN_ADV_REG. In SGMII MAC mode,
* tx_Config_Reg<D15:D0> is the fixed value 0x4001, so this
* step can be skipped.
*/
if (pcs_misc_ctl_reg.s.mode) {
/* 1000BASE-X */
union cvmx_pcsx_anx_adv_reg pcsx_anx_adv_reg;
pcsx_anx_adv_reg.u64 =
cvmx_read_csr(CVMX_PCSX_ANX_ADV_REG(index, interface));
pcsx_anx_adv_reg.s.rem_flt = 0;
pcsx_anx_adv_reg.s.pause = 3;
pcsx_anx_adv_reg.s.hfd = 1;
pcsx_anx_adv_reg.s.fd = 1;
cvmx_write_csr(CVMX_PCSX_ANX_ADV_REG(index, interface),
pcsx_anx_adv_reg.u64);
} else {
union cvmx_pcsx_miscx_ctl_reg pcsx_miscx_ctl_reg;
pcsx_miscx_ctl_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
if (pcsx_miscx_ctl_reg.s.mac_phy) {
/* PHY Mode */
union cvmx_pcsx_sgmx_an_adv_reg pcsx_sgmx_an_adv_reg;
pcsx_sgmx_an_adv_reg.u64 =
cvmx_read_csr(CVMX_PCSX_SGMX_AN_ADV_REG
(index, interface));
pcsx_sgmx_an_adv_reg.s.link = 1;
pcsx_sgmx_an_adv_reg.s.dup = 1;
pcsx_sgmx_an_adv_reg.s.speed = 2;
cvmx_write_csr(CVMX_PCSX_SGMX_AN_ADV_REG
(index, interface),
pcsx_sgmx_an_adv_reg.u64);
} else {
/* MAC Mode - Nothing to do */
}
}
return 0;
}
/**
* Initialize the SERTES link for the first time or after a loss
* of link.
*
* @interface: Interface to init
* @index: Index of prot on the interface
*
* Returns Zero on success, negative on failure
*/
static int __cvmx_helper_sgmii_hardware_init_link(int interface, int index)
{
union cvmx_pcsx_mrx_control_reg control_reg;
/*
* Take PCS through a reset sequence.
* PCS*_MR*_CONTROL_REG[PWR_DN] should be cleared to zero.
* Write PCS*_MR*_CONTROL_REG[RESET]=1 (while not changing the
* value of the other PCS*_MR*_CONTROL_REG bits). Read
* PCS*_MR*_CONTROL_REG[RESET] until it changes value to
* zero.
*/
control_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface));
if (cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) {
control_reg.s.reset = 1;
cvmx_write_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface),
control_reg.u64);
if (CVMX_WAIT_FOR_FIELD64
(CVMX_PCSX_MRX_CONTROL_REG(index, interface),
union cvmx_pcsx_mrx_control_reg, reset, ==, 0, 10000)) {
cvmx_dprintf("SGMII%d: Timeout waiting for port %d "
"to finish reset\n",
interface, index);
return -1;
}
}
/*
* Write PCS*_MR*_CONTROL_REG[RST_AN]=1 to ensure a fresh
* sgmii negotiation starts.
*/
control_reg.s.rst_an = 1;
control_reg.s.an_en = 1;
control_reg.s.pwr_dn = 0;
cvmx_write_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface),
control_reg.u64);
/*
* Wait for PCS*_MR*_STATUS_REG[AN_CPT] to be set, indicating
* that sgmii autonegotiation is complete. In MAC mode this
* isn't an ethernet link, but a link between Octeon and the
* PHY.
*/
if ((cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) &&
CVMX_WAIT_FOR_FIELD64(CVMX_PCSX_MRX_STATUS_REG(index, interface),
union cvmx_pcsx_mrx_status_reg, an_cpt, ==, 1,
10000)) {
/* cvmx_dprintf("SGMII%d: Port %d link timeout\n", interface, index); */
return -1;
}
return 0;
}
/**
* Configure an SGMII link to the specified speed after the SERTES
* link is up.
*
* @interface: Interface to init
* @index: Index of prot on the interface
* @link_info: Link state to configure
*
* Returns Zero on success, negative on failure
*/
static int __cvmx_helper_sgmii_hardware_init_link_speed(int interface,
int index,
cvmx_helper_link_info_t
link_info)
{
int is_enabled;
union cvmx_gmxx_prtx_cfg gmxx_prtx_cfg;
union cvmx_pcsx_miscx_ctl_reg pcsx_miscx_ctl_reg;
/* Disable GMX before we make any changes. Remember the enable state */
gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
is_enabled = gmxx_prtx_cfg.s.en;
gmxx_prtx_cfg.s.en = 0;
cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
/* Wait for GMX to be idle */
if (CVMX_WAIT_FOR_FIELD64
(CVMX_GMXX_PRTX_CFG(index, interface), union cvmx_gmxx_prtx_cfg,
rx_idle, ==, 1, 10000)
|| CVMX_WAIT_FOR_FIELD64(CVMX_GMXX_PRTX_CFG(index, interface),
union cvmx_gmxx_prtx_cfg, tx_idle, ==, 1,
10000)) {
cvmx_dprintf
("SGMII%d: Timeout waiting for port %d to be idle\n",
interface, index);
return -1;
}
/* Read GMX CFG again to make sure the disable completed */
gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
/*
* Get the misc control for PCS. We will need to set the
* duplication amount.
*/
pcsx_miscx_ctl_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
/*
* Use GMXENO to force the link down if the status we get says
* it should be down.
*/
pcsx_miscx_ctl_reg.s.gmxeno = !link_info.s.link_up;
/* Only change the duplex setting if the link is up */
if (link_info.s.link_up)
gmxx_prtx_cfg.s.duplex = link_info.s.full_duplex;
/* Do speed based setting for GMX */
switch (link_info.s.speed) {
case 10:
gmxx_prtx_cfg.s.speed = 0;
gmxx_prtx_cfg.s.speed_msb = 1;
gmxx_prtx_cfg.s.slottime = 0;
/* Setting from GMX-603 */
pcsx_miscx_ctl_reg.s.samp_pt = 25;
cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 64);
cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0);
break;
case 100:
gmxx_prtx_cfg.s.speed = 0;
gmxx_prtx_cfg.s.speed_msb = 0;
gmxx_prtx_cfg.s.slottime = 0;
pcsx_miscx_ctl_reg.s.samp_pt = 0x5;
cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 64);
cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0);
break;
case 1000:
gmxx_prtx_cfg.s.speed = 1;
gmxx_prtx_cfg.s.speed_msb = 0;
gmxx_prtx_cfg.s.slottime = 1;
pcsx_miscx_ctl_reg.s.samp_pt = 1;
cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 512);
cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 8192);
break;
default:
break;
}
/* Write the new misc control for PCS */
cvmx_write_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface),
pcsx_miscx_ctl_reg.u64);
/* Write the new GMX settings with the port still disabled */
cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
/* Read GMX CFG again to make sure the config completed */
gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
/* Restore the enabled / disabled state */
gmxx_prtx_cfg.s.en = is_enabled;
cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
return 0;
}
/**
* Bring up the SGMII interface to be ready for packet I/O but
* leave I/O disabled using the GMX override. This function
* follows the bringup documented in 10.6.3 of the manual.
*
* @interface: Interface to bringup
* @num_ports: Number of ports on the interface
*
* Returns Zero on success, negative on failure
*/
static int __cvmx_helper_sgmii_hardware_init(int interface, int num_ports)
{
int index;
__cvmx_helper_setup_gmx(interface, num_ports);
for (index = 0; index < num_ports; index++) {
int ipd_port = cvmx_helper_get_ipd_port(interface, index);
__cvmx_helper_sgmii_hardware_init_one_time(interface, index);
__cvmx_helper_sgmii_link_set(ipd_port,
__cvmx_helper_sgmii_link_get
(ipd_port));
}
return 0;
}
int __cvmx_helper_sgmii_enumerate(int interface)
{
return 4;
}
/**
* Probe a SGMII interface and determine the number of ports
* connected to it. The SGMII interface should still be down after
* this call.
*
* @interface: Interface to probe
*
* Returns Number of ports on the interface. Zero to disable.
*/
int __cvmx_helper_sgmii_probe(int interface)
{
union cvmx_gmxx_inf_mode mode;
/*
* Due to errata GMX-700 on CN56XXp1.x and CN52XXp1.x, the
* interface needs to be enabled before IPD otherwise per port
* backpressure may not work properly
*/
mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
mode.s.en = 1;
cvmx_write_csr(CVMX_GMXX_INF_MODE(interface), mode.u64);
return __cvmx_helper_sgmii_enumerate(interface);
}
/**
* Bringup and enable a SGMII interface. After this call packet
* I/O should be fully functional. This is called with IPD
* enabled but PKO disabled.
*
* @interface: Interface to bring up
*
* Returns Zero on success, negative on failure
*/
int __cvmx_helper_sgmii_enable(int interface)
{
int num_ports = cvmx_helper_ports_on_interface(interface);
int index;
__cvmx_helper_sgmii_hardware_init(interface, num_ports);
for (index = 0; index < num_ports; index++) {
union cvmx_gmxx_prtx_cfg gmxx_prtx_cfg;
gmxx_prtx_cfg.u64 =
cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
gmxx_prtx_cfg.s.en = 1;
cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface),
gmxx_prtx_cfg.u64);
__cvmx_interrupt_pcsx_intx_en_reg_enable(index, interface);
}
__cvmx_interrupt_pcsxx_int_en_reg_enable(interface);
__cvmx_interrupt_gmxx_enable(interface);
return 0;
}
/**
* Return the link state of an IPD/PKO port as returned by
* auto negotiation. The result of this function may not match
* Octeon's link config if auto negotiation has changed since
* the last call to cvmx_helper_link_set().
*
* @ipd_port: IPD/PKO port to query
*
* Returns Link state
*/
cvmx_helper_link_info_t __cvmx_helper_sgmii_link_get(int ipd_port)
{
cvmx_helper_link_info_t result;
union cvmx_pcsx_miscx_ctl_reg pcs_misc_ctl_reg;
int interface = cvmx_helper_get_interface_num(ipd_port);
int index = cvmx_helper_get_interface_index_num(ipd_port);
union cvmx_pcsx_mrx_control_reg pcsx_mrx_control_reg;
result.u64 = 0;
if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_SIM) {
/* The simulator gives you a simulated 1Gbps full duplex link */
result.s.link_up = 1;
result.s.full_duplex = 1;
result.s.speed = 1000;
return result;
}
pcsx_mrx_control_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface));
if (pcsx_mrx_control_reg.s.loopbck1) {
/* Force 1Gbps full duplex link for internal loopback */
result.s.link_up = 1;
result.s.full_duplex = 1;
result.s.speed = 1000;
return result;
}
pcs_misc_ctl_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
if (pcs_misc_ctl_reg.s.mode) {
/* 1000BASE-X */
/* FIXME */
} else {
union cvmx_pcsx_miscx_ctl_reg pcsx_miscx_ctl_reg;
pcsx_miscx_ctl_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
if (pcsx_miscx_ctl_reg.s.mac_phy) {
/* PHY Mode */
union cvmx_pcsx_mrx_status_reg pcsx_mrx_status_reg;
union cvmx_pcsx_anx_results_reg pcsx_anx_results_reg;
/*
* Don't bother continuing if the SERTES low
* level link is down
*/
pcsx_mrx_status_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MRX_STATUS_REG
(index, interface));
if (pcsx_mrx_status_reg.s.lnk_st == 0) {
if (__cvmx_helper_sgmii_hardware_init_link
(interface, index) != 0)
return result;
}
/* Read the autoneg results */
pcsx_anx_results_reg.u64 =
cvmx_read_csr(CVMX_PCSX_ANX_RESULTS_REG
(index, interface));
if (pcsx_anx_results_reg.s.an_cpt) {
/*
* Auto negotiation is complete. Set
* status accordingly.
*/
result.s.full_duplex =
pcsx_anx_results_reg.s.dup;
result.s.link_up =
pcsx_anx_results_reg.s.link_ok;
switch (pcsx_anx_results_reg.s.spd) {
case 0:
result.s.speed = 10;
break;
case 1:
result.s.speed = 100;
break;
case 2:
result.s.speed = 1000;
break;
default:
result.s.speed = 0;
result.s.link_up = 0;
break;
}
} else {
/*
* Auto negotiation isn't
* complete. Return link down.
*/
result.s.speed = 0;
result.s.link_up = 0;
}
} else { /* MAC Mode */
result = __cvmx_helper_board_link_get(ipd_port);
}
}
return result;
}
/**
* Configure an IPD/PKO port for the specified link state. This
* function does not influence auto negotiation at the PHY level.
* The passed link state must always match the link state returned
* by cvmx_helper_link_get(). It is normally best to use
* cvmx_helper_link_autoconf() instead.
*
* @ipd_port: IPD/PKO port to configure
* @link_info: The new link state
*
* Returns Zero on success, negative on failure
*/
int __cvmx_helper_sgmii_link_set(int ipd_port,
cvmx_helper_link_info_t link_info)
{
int interface = cvmx_helper_get_interface_num(ipd_port);
int index = cvmx_helper_get_interface_index_num(ipd_port);
__cvmx_helper_sgmii_hardware_init_link(interface, index);
return __cvmx_helper_sgmii_hardware_init_link_speed(interface, index,
link_info);
}
/**
* Configure a port for internal and/or external loopback. Internal
* loopback causes packets sent by the port to be received by
* Octeon. External loopback causes packets received from the wire to
* sent out again.
*
* @ipd_port: IPD/PKO port to loopback.
* @enable_internal:
* Non zero if you want internal loopback
* @enable_external:
* Non zero if you want external loopback
*
* Returns Zero on success, negative on failure.
*/
int __cvmx_helper_sgmii_configure_loopback(int ipd_port, int enable_internal,
int enable_external)
{
int interface = cvmx_helper_get_interface_num(ipd_port);
int index = cvmx_helper_get_interface_index_num(ipd_port);
union cvmx_pcsx_mrx_control_reg pcsx_mrx_control_reg;
union cvmx_pcsx_miscx_ctl_reg pcsx_miscx_ctl_reg;
pcsx_mrx_control_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface));
pcsx_mrx_control_reg.s.loopbck1 = enable_internal;
cvmx_write_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface),
pcsx_mrx_control_reg.u64);
pcsx_miscx_ctl_reg.u64 =
cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
pcsx_miscx_ctl_reg.s.loopbck2 = enable_external;
cvmx_write_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface),
pcsx_miscx_ctl_reg.u64);
__cvmx_helper_sgmii_hardware_init_link(interface, index);
return 0;
}