/*
* Freescale GPMI NAND Flash Driver
*
* Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
* Copyright (C) 2008 Embedded Alley Solutions, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
*/
#include <linux/clk.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/mtd/partitions.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_mtd.h>
#include "gpmi-nand.h"
/* Resource names for the GPMI NAND driver. */
#define GPMI_NAND_GPMI_REGS_ADDR_RES_NAME "gpmi-nand"
#define GPMI_NAND_BCH_REGS_ADDR_RES_NAME "bch"
#define GPMI_NAND_BCH_INTERRUPT_RES_NAME "bch"
/* add our owner bbt descriptor */
static uint8_t scan_ff_pattern[] = { 0xff };
static struct nand_bbt_descr gpmi_bbt_descr = {
.options = 0,
.offs = 0,
.len = 1,
.pattern = scan_ff_pattern
};
/*
* We may change the layout if we can get the ECC info from the datasheet,
* else we will use all the (page + OOB).
*/
static struct nand_ecclayout gpmi_hw_ecclayout = {
.eccbytes = 0,
.eccpos = { 0, },
.oobfree = { {.offset = 0, .length = 0} }
};
static irqreturn_t bch_irq(int irq, void *cookie)
{
struct gpmi_nand_data *this = cookie;
gpmi_clear_bch(this);
complete(&this->bch_done);
return IRQ_HANDLED;
}
/*
* Calculate the ECC strength by hand:
* E : The ECC strength.
* G : the length of Galois Field.
* N : The chunk count of per page.
* O : the oobsize of the NAND chip.
* M : the metasize of per page.
*
* The formula is :
* E * G * N
* ------------ <= (O - M)
* 8
*
* So, we get E by:
* (O - M) * 8
* E <= -------------
* G * N
*/
static inline int get_ecc_strength(struct gpmi_nand_data *this)
{
struct bch_geometry *geo = &this->bch_geometry;
struct mtd_info *mtd = &this->mtd;
int ecc_strength;
ecc_strength = ((mtd->oobsize - geo->metadata_size) * 8)
/ (geo->gf_len * geo->ecc_chunk_count);
/* We need the minor even number. */
return round_down(ecc_strength, 2);
}
static inline bool gpmi_check_ecc(struct gpmi_nand_data *this)
{
struct bch_geometry *geo = &this->bch_geometry;
/* Do the sanity check. */
if (GPMI_IS_MX23(this) || GPMI_IS_MX28(this)) {
/* The mx23/mx28 only support the GF13. */
if (geo->gf_len == 14)
return false;
if (geo->ecc_strength > MXS_ECC_STRENGTH_MAX)
return false;
} else if (GPMI_IS_MX6Q(this)) {
if (geo->ecc_strength > MX6_ECC_STRENGTH_MAX)
return false;
}
return true;
}
/*
* If we can get the ECC information from the nand chip, we do not
* need to calculate them ourselves.
*
* We may have available oob space in this case.
*/
static bool set_geometry_by_ecc_info(struct gpmi_nand_data *this)
{
struct bch_geometry *geo = &this->bch_geometry;
struct mtd_info *mtd = &this->mtd;
struct nand_chip *chip = mtd->priv;
struct nand_oobfree *of = gpmi_hw_ecclayout.oobfree;
unsigned int block_mark_bit_offset;
if (!(chip->ecc_strength_ds > 0 && chip->ecc_step_ds > 0))
return false;
switch (chip->ecc_step_ds) {
case SZ_512:
geo->gf_len = 13;
break;
case SZ_1K:
geo->gf_len = 14;
break;
default:
dev_err(this->dev,
"unsupported nand chip. ecc bits : %d, ecc size : %d\n",
chip->ecc_strength_ds, chip->ecc_step_ds);
return false;
}
geo->ecc_chunk_size = chip->ecc_step_ds;
geo->ecc_strength = round_up(chip->ecc_strength_ds, 2);
if (!gpmi_check_ecc(this))
return false;
/* Keep the C >= O */
if (geo->ecc_chunk_size < mtd->oobsize) {
dev_err(this->dev,
"unsupported nand chip. ecc size: %d, oob size : %d\n",
chip->ecc_step_ds, mtd->oobsize);
return false;
}
/* The default value, see comment in the legacy_set_geometry(). */
geo->metadata_size = 10;
geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunk_size;
/*
* Now, the NAND chip with 2K page(data chunk is 512byte) shows below:
*
* | P |
* |<----------------------------------------------------->|
* | |
* | (Block Mark) |
* | P' | | | |
* |<-------------------------------------------->| D | | O' |
* | |<---->| |<--->|
* V V V V V
* +---+----------+-+----------+-+----------+-+----------+-+-----+
* | M | data |E| data |E| data |E| data |E| |
* +---+----------+-+----------+-+----------+-+----------+-+-----+
* ^ ^
* | O |
* |<------------>|
* | |
*
* P : the page size for BCH module.
* E : The ECC strength.
* G : the length of Galois Field.
* N : The chunk count of per page.
* M : the metasize of per page.
* C : the ecc chunk size, aka the "data" above.
* P': the nand chip's page size.
* O : the nand chip's oob size.
* O': the free oob.
*
* The formula for P is :
*
* E * G * N
* P = ------------ + P' + M
* 8
*
* The position of block mark moves forward in the ECC-based view
* of page, and the delta is:
*
* E * G * (N - 1)
* D = (---------------- + M)
* 8
*
* Please see the comment in legacy_set_geometry().
* With the condition C >= O , we still can get same result.
* So the bit position of the physical block mark within the ECC-based
* view of the page is :
* (P' - D) * 8
*/
geo->page_size = mtd->writesize + geo->metadata_size +
(geo->gf_len * geo->ecc_strength * geo->ecc_chunk_count) / 8;
/* The available oob size we have. */
if (geo->page_size < mtd->writesize + mtd->oobsize) {
of->offset = geo->page_size - mtd->writesize;
of->length = mtd->oobsize - of->offset;
}
geo->payload_size = mtd->writesize;
geo->auxiliary_status_offset = ALIGN(geo->metadata_size, 4);
geo->auxiliary_size = ALIGN(geo->metadata_size, 4)
+ ALIGN(geo->ecc_chunk_count, 4);
if (!this->swap_block_mark)
return true;
/* For bit swap. */
block_mark_bit_offset = mtd->writesize * 8 -
(geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1)
+ geo->metadata_size * 8);
geo->block_mark_byte_offset = block_mark_bit_offset / 8;
geo->block_mark_bit_offset = block_mark_bit_offset % 8;
return true;
}
static int legacy_set_geometry(struct gpmi_nand_data *this)
{
struct bch_geometry *geo = &this->bch_geometry;
struct mtd_info *mtd = &this->mtd;
unsigned int metadata_size;
unsigned int status_size;
unsigned int block_mark_bit_offset;
/*
* The size of the metadata can be changed, though we set it to 10
* bytes now. But it can't be too large, because we have to save
* enough space for BCH.
*/
geo->metadata_size = 10;
/* The default for the length of Galois Field. */
geo->gf_len = 13;
/* The default for chunk size. */
geo->ecc_chunk_size = 512;
while (geo->ecc_chunk_size < mtd->oobsize) {
geo->ecc_chunk_size *= 2; /* keep C >= O */
geo->gf_len = 14;
}
geo->ecc_chunk_count = mtd->writesize / geo->ecc_chunk_size;
/* We use the same ECC strength for all chunks. */
geo->ecc_strength = get_ecc_strength(this);
if (!gpmi_check_ecc(this)) {
dev_err(this->dev,
"We can not support this nand chip."
" Its required ecc strength(%d) is beyond our"
" capability(%d).\n", geo->ecc_strength,
(GPMI_IS_MX6Q(this) ? MX6_ECC_STRENGTH_MAX
: MXS_ECC_STRENGTH_MAX));
return -EINVAL;
}
geo->page_size = mtd->writesize + mtd->oobsize;
geo->payload_size = mtd->writesize;
/*
* The auxiliary buffer contains the metadata and the ECC status. The
* metadata is padded to the nearest 32-bit boundary. The ECC status
* contains one byte for every ECC chunk, and is also padded to the
* nearest 32-bit boundary.
*/
metadata_size = ALIGN(geo->metadata_size, 4);
status_size = ALIGN(geo->ecc_chunk_count, 4);
geo->auxiliary_size = metadata_size + status_size;
geo->auxiliary_status_offset = metadata_size;
if (!this->swap_block_mark)
return 0;
/*
* We need to compute the byte and bit offsets of
* the physical block mark within the ECC-based view of the page.
*
* NAND chip with 2K page shows below:
* (Block Mark)
* | |
* | D |
* |<---->|
* V V
* +---+----------+-+----------+-+----------+-+----------+-+
* | M | data |E| data |E| data |E| data |E|
* +---+----------+-+----------+-+----------+-+----------+-+
*
* The position of block mark moves forward in the ECC-based view
* of page, and the delta is:
*
* E * G * (N - 1)
* D = (---------------- + M)
* 8
*
* With the formula to compute the ECC strength, and the condition
* : C >= O (C is the ecc chunk size)
*
* It's easy to deduce to the following result:
*
* E * G (O - M) C - M C - M
* ----------- <= ------- <= -------- < ---------
* 8 N N (N - 1)
*
* So, we get:
*
* E * G * (N - 1)
* D = (---------------- + M) < C
* 8
*
* The above inequality means the position of block mark
* within the ECC-based view of the page is still in the data chunk,
* and it's NOT in the ECC bits of the chunk.
*
* Use the following to compute the bit position of the
* physical block mark within the ECC-based view of the page:
* (page_size - D) * 8
*
* --Huang Shijie
*/
block_mark_bit_offset = mtd->writesize * 8 -
(geo->ecc_strength * geo->gf_len * (geo->ecc_chunk_count - 1)
+ geo->metadata_size * 8);
geo->block_mark_byte_offset = block_mark_bit_offset / 8;
geo->block_mark_bit_offset = block_mark_bit_offset % 8;
return 0;
}
int common_nfc_set_geometry(struct gpmi_nand_data *this)
{
if (of_property_read_bool(this->dev->of_node, "fsl,use-minimum-ecc")
&& set_geometry_by_ecc_info(this))
return 0;
return legacy_set_geometry(this);
}
struct dma_chan *get_dma_chan(struct gpmi_nand_data *this)
{
/* We use the DMA channel 0 to access all the nand chips. */
return this->dma_chans[0];
}
/* Can we use the upper's buffer directly for DMA? */
void prepare_data_dma(struct gpmi_nand_data *this, enum dma_data_direction dr)
{
struct scatterlist *sgl = &this->data_sgl;
int ret;
/* first try to map the upper buffer directly */
if (virt_addr_valid(this->upper_buf) &&
!object_is_on_stack(this->upper_buf)) {
sg_init_one(sgl, this->upper_buf, this->upper_len);
ret = dma_map_sg(this->dev, sgl, 1, dr);
if (ret == 0)
goto map_fail;
this->direct_dma_map_ok = true;
return;
}
map_fail:
/* We have to use our own DMA buffer. */
sg_init_one(sgl, this->data_buffer_dma, this->upper_len);
if (dr == DMA_TO_DEVICE)
memcpy(this->data_buffer_dma, this->upper_buf, this->upper_len);
dma_map_sg(this->dev, sgl, 1, dr);
this->direct_dma_map_ok = false;
}
/* This will be called after the DMA operation is finished. */
static void dma_irq_callback(void *param)
{
struct gpmi_nand_data *this = param;
struct completion *dma_c = &this->dma_done;
switch (this->dma_type) {
case DMA_FOR_COMMAND:
dma_unmap_sg(this->dev, &this->cmd_sgl, 1, DMA_TO_DEVICE);
break;
case DMA_FOR_READ_DATA:
dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_FROM_DEVICE);
if (this->direct_dma_map_ok == false)
memcpy(this->upper_buf, this->data_buffer_dma,
this->upper_len);
break;
case DMA_FOR_WRITE_DATA:
dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_TO_DEVICE);
break;
case DMA_FOR_READ_ECC_PAGE:
case DMA_FOR_WRITE_ECC_PAGE:
/* We have to wait the BCH interrupt to finish. */
break;
default:
dev_err(this->dev, "in wrong DMA operation.\n");
}
complete(dma_c);
}
int start_dma_without_bch_irq(struct gpmi_nand_data *this,
struct dma_async_tx_descriptor *desc)
{
struct completion *dma_c = &this->dma_done;
int err;
init_completion(dma_c);
desc->callback = dma_irq_callback;
desc->callback_param = this;
dmaengine_submit(desc);
dma_async_issue_pending(get_dma_chan(this));
/* Wait for the interrupt from the DMA block. */
err = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000));
if (!err) {
dev_err(this->dev, "DMA timeout, last DMA :%d\n",
this->last_dma_type);
gpmi_dump_info(this);
return -ETIMEDOUT;
}
return 0;
}
/*
* This function is used in BCH reading or BCH writing pages.
* It will wait for the BCH interrupt as long as ONE second.
* Actually, we must wait for two interrupts :
* [1] firstly the DMA interrupt and
* [2] secondly the BCH interrupt.
*/
int start_dma_with_bch_irq(struct gpmi_nand_data *this,
struct dma_async_tx_descriptor *desc)
{
struct completion *bch_c = &this->bch_done;
int err;
/* Prepare to receive an interrupt from the BCH block. */
init_completion(bch_c);
/* start the DMA */
start_dma_without_bch_irq(this, desc);
/* Wait for the interrupt from the BCH block. */
err = wait_for_completion_timeout(bch_c, msecs_to_jiffies(1000));
if (!err) {
dev_err(this->dev, "BCH timeout, last DMA :%d\n",
this->last_dma_type);
gpmi_dump_info(this);
return -ETIMEDOUT;
}
return 0;
}
static int acquire_register_block(struct gpmi_nand_data *this,
const char *res_name)
{
struct platform_device *pdev = this->pdev;
struct resources *res = &this->resources;
struct resource *r;
void __iomem *p;
r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name);
p = devm_ioremap_resource(&pdev->dev, r);
if (IS_ERR(p))
return PTR_ERR(p);
if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME))
res->gpmi_regs = p;
else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME))
res->bch_regs = p;
else
dev_err(this->dev, "unknown resource name : %s\n", res_name);
return 0;
}
static int acquire_bch_irq(struct gpmi_nand_data *this, irq_handler_t irq_h)
{
struct platform_device *pdev = this->pdev;
const char *res_name = GPMI_NAND_BCH_INTERRUPT_RES_NAME;
struct resource *r;
int err;
r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, res_name);
if (!r) {
dev_err(this->dev, "Can't get resource for %s\n", res_name);
return -ENODEV;
}
err = devm_request_irq(this->dev, r->start, irq_h, 0, res_name, this);
if (err)
dev_err(this->dev, "error requesting BCH IRQ\n");
return err;
}
static void release_dma_channels(struct gpmi_nand_data *this)
{
unsigned int i;
for (i = 0; i < DMA_CHANS; i++)
if (this->dma_chans[i]) {
dma_release_channel(this->dma_chans[i]);
this->dma_chans[i] = NULL;
}
}
static int acquire_dma_channels(struct gpmi_nand_data *this)
{
struct platform_device *pdev = this->pdev;
struct dma_chan *dma_chan;
/* request dma channel */
dma_chan = dma_request_slave_channel(&pdev->dev, "rx-tx");
if (!dma_chan) {
dev_err(this->dev, "Failed to request DMA channel.\n");
goto acquire_err;
}
this->dma_chans[0] = dma_chan;
return 0;
acquire_err:
release_dma_channels(this);
return -EINVAL;
}
static char *extra_clks_for_mx6q[GPMI_CLK_MAX] = {
"gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch",
};
static int gpmi_get_clks(struct gpmi_nand_data *this)
{
struct resources *r = &this->resources;
char **extra_clks = NULL;
struct clk *clk;
int err, i;
/* The main clock is stored in the first. */
r->clock[0] = devm_clk_get(this->dev, "gpmi_io");
if (IS_ERR(r->clock[0])) {
err = PTR_ERR(r->clock[0]);
goto err_clock;
}
/* Get extra clocks */
if (GPMI_IS_MX6Q(this))
extra_clks = extra_clks_for_mx6q;
if (!extra_clks)
return 0;
for (i = 1; i < GPMI_CLK_MAX; i++) {
if (extra_clks[i - 1] == NULL)
break;
clk = devm_clk_get(this->dev, extra_clks[i - 1]);
if (IS_ERR(clk)) {
err = PTR_ERR(clk);
goto err_clock;
}
r->clock[i] = clk;
}
if (GPMI_IS_MX6Q(this))
/*
* Set the default value for the gpmi clock in mx6q:
*
* If you want to use the ONFI nand which is in the
* Synchronous Mode, you should change the clock as you need.
*/
clk_set_rate(r->clock[0], 22000000);
return 0;
err_clock:
dev_dbg(this->dev, "failed in finding the clocks.\n");
return err;
}
static int acquire_resources(struct gpmi_nand_data *this)
{
int ret;
ret = acquire_register_block(this, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME);
if (ret)
goto exit_regs;
ret = acquire_register_block(this, GPMI_NAND_BCH_REGS_ADDR_RES_NAME);
if (ret)
goto exit_regs;
ret = acquire_bch_irq(this, bch_irq);
if (ret)
goto exit_regs;
ret = acquire_dma_channels(this);
if (ret)
goto exit_regs;
ret = gpmi_get_clks(this);
if (ret)
goto exit_clock;
return 0;
exit_clock:
release_dma_channels(this);
exit_regs:
return ret;
}
static void release_resources(struct gpmi_nand_data *this)
{
release_dma_channels(this);
}
static int init_hardware(struct gpmi_nand_data *this)
{
int ret;
/*
* This structure contains the "safe" GPMI timing that should succeed
* with any NAND Flash device
* (although, with less-than-optimal performance).
*/
struct nand_timing safe_timing = {
.data_setup_in_ns = 80,
.data_hold_in_ns = 60,
.address_setup_in_ns = 25,
.gpmi_sample_delay_in_ns = 6,
.tREA_in_ns = -1,
.tRLOH_in_ns = -1,
.tRHOH_in_ns = -1,
};
/* Initialize the hardwares. */
ret = gpmi_init(this);
if (ret)
return ret;
this->timing = safe_timing;
return 0;
}
static int read_page_prepare(struct gpmi_nand_data *this,
void *destination, unsigned length,
void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
void **use_virt, dma_addr_t *use_phys)
{
struct device *dev = this->dev;
if (virt_addr_valid(destination)) {
dma_addr_t dest_phys;
dest_phys = dma_map_single(dev, destination,
length, DMA_FROM_DEVICE);
if (dma_mapping_error(dev, dest_phys)) {
if (alt_size < length) {
dev_err(dev, "Alternate buffer is too small\n");
return -ENOMEM;
}
goto map_failed;
}
*use_virt = destination;
*use_phys = dest_phys;
this->direct_dma_map_ok = true;
return 0;
}
map_failed:
*use_virt = alt_virt;
*use_phys = alt_phys;
this->direct_dma_map_ok = false;
return 0;
}
static inline void read_page_end(struct gpmi_nand_data *this,
void *destination, unsigned length,
void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
void *used_virt, dma_addr_t used_phys)
{
if (this->direct_dma_map_ok)
dma_unmap_single(this->dev, used_phys, length, DMA_FROM_DEVICE);
}
static inline void read_page_swap_end(struct gpmi_nand_data *this,
void *destination, unsigned length,
void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
void *used_virt, dma_addr_t used_phys)
{
if (!this->direct_dma_map_ok)
memcpy(destination, alt_virt, length);
}
static int send_page_prepare(struct gpmi_nand_data *this,
const void *source, unsigned length,
void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
const void **use_virt, dma_addr_t *use_phys)
{
struct device *dev = this->dev;
if (virt_addr_valid(source)) {
dma_addr_t source_phys;
source_phys = dma_map_single(dev, (void *)source, length,
DMA_TO_DEVICE);
if (dma_mapping_error(dev, source_phys)) {
if (alt_size < length) {
dev_err(dev, "Alternate buffer is too small\n");
return -ENOMEM;
}
goto map_failed;
}
*use_virt = source;
*use_phys = source_phys;
return 0;
}
map_failed:
/*
* Copy the content of the source buffer into the alternate
* buffer and set up the return values accordingly.
*/
memcpy(alt_virt, source, length);
*use_virt = alt_virt;
*use_phys = alt_phys;
return 0;
}
static void send_page_end(struct gpmi_nand_data *this,
const void *source, unsigned length,
void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
const void *used_virt, dma_addr_t used_phys)
{
struct device *dev = this->dev;
if (used_virt == source)
dma_unmap_single(dev, used_phys, length, DMA_TO_DEVICE);
}
static void gpmi_free_dma_buffer(struct gpmi_nand_data *this)
{
struct device *dev = this->dev;
if (this->page_buffer_virt && virt_addr_valid(this->page_buffer_virt))
dma_free_coherent(dev, this->page_buffer_size,
this->page_buffer_virt,
this->page_buffer_phys);
kfree(this->cmd_buffer);
kfree(this->data_buffer_dma);
this->cmd_buffer = NULL;
this->data_buffer_dma = NULL;
this->page_buffer_virt = NULL;
this->page_buffer_size = 0;
}
/* Allocate the DMA buffers */
static int gpmi_alloc_dma_buffer(struct gpmi_nand_data *this)
{
struct bch_geometry *geo = &this->bch_geometry;
struct device *dev = this->dev;
struct mtd_info *mtd = &this->mtd;
/* [1] Allocate a command buffer. PAGE_SIZE is enough. */
this->cmd_buffer = kzalloc(PAGE_SIZE, GFP_DMA | GFP_KERNEL);
if (this->cmd_buffer == NULL)
goto error_alloc;
/*
* [2] Allocate a read/write data buffer.
* The gpmi_alloc_dma_buffer can be called twice.
* We allocate a PAGE_SIZE length buffer if gpmi_alloc_dma_buffer
* is called before the nand_scan_ident; and we allocate a buffer
* of the real NAND page size when the gpmi_alloc_dma_buffer is
* called after the nand_scan_ident.
*/
this->data_buffer_dma = kzalloc(mtd->writesize ?: PAGE_SIZE,
GFP_DMA | GFP_KERNEL);
if (this->data_buffer_dma == NULL)
goto error_alloc;
/*
* [3] Allocate the page buffer.
*
* Both the payload buffer and the auxiliary buffer must appear on
* 32-bit boundaries. We presume the size of the payload buffer is a
* power of two and is much larger than four, which guarantees the
* auxiliary buffer will appear on a 32-bit boundary.
*/
this->page_buffer_size = geo->payload_size + geo->auxiliary_size;
this->page_buffer_virt = dma_alloc_coherent(dev, this->page_buffer_size,
&this->page_buffer_phys, GFP_DMA);
if (!this->page_buffer_virt)
goto error_alloc;
/* Slice up the page buffer. */
this->payload_virt = this->page_buffer_virt;
this->payload_phys = this->page_buffer_phys;
this->auxiliary_virt = this->payload_virt + geo->payload_size;
this->auxiliary_phys = this->payload_phys + geo->payload_size;
return 0;
error_alloc:
gpmi_free_dma_buffer(this);
return -ENOMEM;
}
static void gpmi_cmd_ctrl(struct mtd_info *mtd, int data, unsigned int ctrl)
{
struct nand_chip *chip = mtd->priv;
struct gpmi_nand_data *this = chip->priv;
int ret;
/*
* Every operation begins with a command byte and a series of zero or
* more address bytes. These are distinguished by either the Address
* Latch Enable (ALE) or Command Latch Enable (CLE) signals being
* asserted. When MTD is ready to execute the command, it will deassert
* both latch enables.
*
* Rather than run a separate DMA operation for every single byte, we
* queue them up and run a single DMA operation for the entire series
* of command and data bytes. NAND_CMD_NONE means the END of the queue.
*/
if ((ctrl & (NAND_ALE | NAND_CLE))) {
if (data != NAND_CMD_NONE)
this->cmd_buffer[this->command_length++] = data;
return;
}
if (!this->command_length)
return;
ret = gpmi_send_command(this);
if (ret)
dev_err(this->dev, "Chip: %u, Error %d\n",
this->current_chip, ret);
this->command_length = 0;
}
static int gpmi_dev_ready(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
struct gpmi_nand_data *this = chip->priv;
return gpmi_is_ready(this, this->current_chip);
}
static void gpmi_select_chip(struct mtd_info *mtd, int chipnr)
{
struct nand_chip *chip = mtd->priv;
struct gpmi_nand_data *this = chip->priv;
if ((this->current_chip < 0) && (chipnr >= 0))
gpmi_begin(this);
else if ((this->current_chip >= 0) && (chipnr < 0))
gpmi_end(this);
this->current_chip = chipnr;
}
static void gpmi_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
{
struct nand_chip *chip = mtd->priv;
struct gpmi_nand_data *this = chip->priv;
dev_dbg(this->dev, "len is %d\n", len);
this->upper_buf = buf;
this->upper_len = len;
gpmi_read_data(this);
}
static void gpmi_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
{
struct nand_chip *chip = mtd->priv;
struct gpmi_nand_data *this = chip->priv;
dev_dbg(this->dev, "len is %d\n", len);
this->upper_buf = (uint8_t *)buf;
this->upper_len = len;
gpmi_send_data(this);
}
static uint8_t gpmi_read_byte(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
struct gpmi_nand_data *this = chip->priv;
uint8_t *buf = this->data_buffer_dma;
gpmi_read_buf(mtd, buf, 1);
return buf[0];
}
/*
* Handles block mark swapping.
* It can be called in swapping the block mark, or swapping it back,
* because the the operations are the same.
*/
static void block_mark_swapping(struct gpmi_nand_data *this,
void *payload, void *auxiliary)
{
struct bch_geometry *nfc_geo = &this->bch_geometry;
unsigned char *p;
unsigned char *a;
unsigned int bit;
unsigned char mask;
unsigned char from_data;
unsigned char from_oob;
if (!this->swap_block_mark)
return;
/*
* If control arrives here, we're swapping. Make some convenience
* variables.
*/
bit = nfc_geo->block_mark_bit_offset;
p = payload + nfc_geo->block_mark_byte_offset;
a = auxiliary;
/*
* Get the byte from the data area that overlays the block mark. Since
* the ECC engine applies its own view to the bits in the page, the
* physical block mark won't (in general) appear on a byte boundary in
* the data.
*/
from_data = (p[0] >> bit) | (p[1] << (8 - bit));
/* Get the byte from the OOB. */
from_oob = a[0];
/* Swap them. */
a[0] = from_data;
mask = (0x1 << bit) - 1;
p[0] = (p[0] & mask) | (from_oob << bit);
mask = ~0 << bit;
p[1] = (p[1] & mask) | (from_oob >> (8 - bit));
}
static int gpmi_ecc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
uint8_t *buf, int oob_required, int page)
{
struct gpmi_nand_data *this = chip->priv;
struct bch_geometry *nfc_geo = &this->bch_geometry;
void *payload_virt;
dma_addr_t payload_phys;
void *auxiliary_virt;
dma_addr_t auxiliary_phys;
unsigned int i;
unsigned char *status;
unsigned int max_bitflips = 0;
int ret;
dev_dbg(this->dev, "page number is : %d\n", page);
ret = read_page_prepare(this, buf, mtd->writesize,
this->payload_virt, this->payload_phys,
nfc_geo->payload_size,
&payload_virt, &payload_phys);
if (ret) {
dev_err(this->dev, "Inadequate DMA buffer\n");
ret = -ENOMEM;
return ret;
}
auxiliary_virt = this->auxiliary_virt;
auxiliary_phys = this->auxiliary_phys;
/* go! */
ret = gpmi_read_page(this, payload_phys, auxiliary_phys);
read_page_end(this, buf, mtd->writesize,
this->payload_virt, this->payload_phys,
nfc_geo->payload_size,
payload_virt, payload_phys);
if (ret) {
dev_err(this->dev, "Error in ECC-based read: %d\n", ret);
return ret;
}
/* handle the block mark swapping */
block_mark_swapping(this, payload_virt, auxiliary_virt);
/* Loop over status bytes, accumulating ECC status. */
status = auxiliary_virt + nfc_geo->auxiliary_status_offset;
for (i = 0; i < nfc_geo->ecc_chunk_count; i++, status++) {
if ((*status == STATUS_GOOD) || (*status == STATUS_ERASED))
continue;
if (*status == STATUS_UNCORRECTABLE) {
mtd->ecc_stats.failed++;
continue;
}
mtd->ecc_stats.corrected += *status;
max_bitflips = max_t(unsigned int, max_bitflips, *status);
}
if (oob_required) {
/*
* It's time to deliver the OOB bytes. See gpmi_ecc_read_oob()
* for details about our policy for delivering the OOB.
*
* We fill the caller's buffer with set bits, and then copy the
* block mark to th caller's buffer. Note that, if block mark
* swapping was necessary, it has already been done, so we can
* rely on the first byte of the auxiliary buffer to contain
* the block mark.
*/
memset(chip->oob_poi, ~0, mtd->oobsize);
chip->oob_poi[0] = ((uint8_t *) auxiliary_virt)[0];
}
read_page_swap_end(this, buf, mtd->writesize,
this->payload_virt, this->payload_phys,
nfc_geo->payload_size,
payload_virt, payload_phys);
return max_bitflips;
}
static int gpmi_ecc_write_page(struct mtd_info *mtd, struct nand_chip *chip,
const uint8_t *buf, int oob_required)
{
struct gpmi_nand_data *this = chip->priv;
struct bch_geometry *nfc_geo = &this->bch_geometry;
const void *payload_virt;
dma_addr_t payload_phys;
const void *auxiliary_virt;
dma_addr_t auxiliary_phys;
int ret;
dev_dbg(this->dev, "ecc write page.\n");
if (this->swap_block_mark) {
/*
* If control arrives here, we're doing block mark swapping.
* Since we can't modify the caller's buffers, we must copy them
* into our own.
*/
memcpy(this->payload_virt, buf, mtd->writesize);
payload_virt = this->payload_virt;
payload_phys = this->payload_phys;
memcpy(this->auxiliary_virt, chip->oob_poi,
nfc_geo->auxiliary_size);
auxiliary_virt = this->auxiliary_virt;
auxiliary_phys = this->auxiliary_phys;
/* Handle block mark swapping. */
block_mark_swapping(this,
(void *) payload_virt, (void *) auxiliary_virt);
} else {
/*
* If control arrives here, we're not doing block mark swapping,
* so we can to try and use the caller's buffers.
*/
ret = send_page_prepare(this,
buf, mtd->writesize,
this->payload_virt, this->payload_phys,
nfc_geo->payload_size,
&payload_virt, &payload_phys);
if (ret) {
dev_err(this->dev, "Inadequate payload DMA buffer\n");
return 0;
}
ret = send_page_prepare(this,
chip->oob_poi, mtd->oobsize,
this->auxiliary_virt, this->auxiliary_phys,
nfc_geo->auxiliary_size,
&auxiliary_virt, &auxiliary_phys);
if (ret) {
dev_err(this->dev, "Inadequate auxiliary DMA buffer\n");
goto exit_auxiliary;
}
}
/* Ask the NFC. */
ret = gpmi_send_page(this, payload_phys, auxiliary_phys);
if (ret)
dev_err(this->dev, "Error in ECC-based write: %d\n", ret);
if (!this->swap_block_mark) {
send_page_end(this, chip->oob_poi, mtd->oobsize,
this->auxiliary_virt, this->auxiliary_phys,
nfc_geo->auxiliary_size,
auxiliary_virt, auxiliary_phys);
exit_auxiliary:
send_page_end(this, buf, mtd->writesize,
this->payload_virt, this->payload_phys,
nfc_geo->payload_size,
payload_virt, payload_phys);
}
return 0;
}
/*
* There are several places in this driver where we have to handle the OOB and
* block marks. This is the function where things are the most complicated, so
* this is where we try to explain it all. All the other places refer back to
* here.
*
* These are the rules, in order of decreasing importance:
*
* 1) Nothing the caller does can be allowed to imperil the block mark.
*
* 2) In read operations, the first byte of the OOB we return must reflect the
* true state of the block mark, no matter where that block mark appears in
* the physical page.
*
* 3) ECC-based read operations return an OOB full of set bits (since we never
* allow ECC-based writes to the OOB, it doesn't matter what ECC-based reads
* return).
*
* 4) "Raw" read operations return a direct view of the physical bytes in the
* page, using the conventional definition of which bytes are data and which
* are OOB. This gives the caller a way to see the actual, physical bytes
* in the page, without the distortions applied by our ECC engine.
*
*
* What we do for this specific read operation depends on two questions:
*
* 1) Are we doing a "raw" read, or an ECC-based read?
*
* 2) Are we using block mark swapping or transcription?
*
* There are four cases, illustrated by the following Karnaugh map:
*
* | Raw | ECC-based |
* -------------+-------------------------+-------------------------+
* | Read the conventional | |
* | OOB at the end of the | |
* Swapping | page and return it. It | |
* | contains exactly what | |
* | we want. | Read the block mark and |
* -------------+-------------------------+ return it in a buffer |
* | Read the conventional | full of set bits. |
* | OOB at the end of the | |
* | page and also the block | |
* Transcribing | mark in the metadata. | |
* | Copy the block mark | |
* | into the first byte of | |
* | the OOB. | |
* -------------+-------------------------+-------------------------+
*
* Note that we break rule #4 in the Transcribing/Raw case because we're not
* giving an accurate view of the actual, physical bytes in the page (we're
* overwriting the block mark). That's OK because it's more important to follow
* rule #2.
*
* It turns out that knowing whether we want an "ECC-based" or "raw" read is not
* easy. When reading a page, for example, the NAND Flash MTD code calls our
* ecc.read_page or ecc.read_page_raw function. Thus, the fact that MTD wants an
* ECC-based or raw view of the page is implicit in which function it calls
* (there is a similar pair of ECC-based/raw functions for writing).
*
* FIXME: The following paragraph is incorrect, now that there exist
* ecc.read_oob_raw and ecc.write_oob_raw functions.
*
* Since MTD assumes the OOB is not covered by ECC, there is no pair of
* ECC-based/raw functions for reading or or writing the OOB. The fact that the
* caller wants an ECC-based or raw view of the page is not propagated down to
* this driver.
*/
static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
int page)
{
struct gpmi_nand_data *this = chip->priv;
dev_dbg(this->dev, "page number is %d\n", page);
/* clear the OOB buffer */
memset(chip->oob_poi, ~0, mtd->oobsize);
/* Read out the conventional OOB. */
chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page);
chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
/*
* Now, we want to make sure the block mark is correct. In the
* Swapping/Raw case, we already have it. Otherwise, we need to
* explicitly read it.
*/
if (!this->swap_block_mark) {
/* Read the block mark into the first byte of the OOB buffer. */
chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
chip->oob_poi[0] = chip->read_byte(mtd);
}
return 0;
}
static int
gpmi_ecc_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page)
{
struct nand_oobfree *of = mtd->ecclayout->oobfree;
int status = 0;
/* Do we have available oob area? */
if (!of->length)
return -EPERM;
if (!nand_is_slc(chip))
return -EPERM;
chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize + of->offset, page);
chip->write_buf(mtd, chip->oob_poi + of->offset, of->length);
chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
status = chip->waitfunc(mtd, chip);
return status & NAND_STATUS_FAIL ? -EIO : 0;
}
static int gpmi_block_markbad(struct mtd_info *mtd, loff_t ofs)
{
struct nand_chip *chip = mtd->priv;
struct gpmi_nand_data *this = chip->priv;
int ret = 0;
uint8_t *block_mark;
int column, page, status, chipnr;
chipnr = (int)(ofs >> chip->chip_shift);
chip->select_chip(mtd, chipnr);
column = this->swap_block_mark ? mtd->writesize : 0;
/* Write the block mark. */
block_mark = this->data_buffer_dma;
block_mark[0] = 0; /* bad block marker */
/* Shift to get page */
page = (int)(ofs >> chip->page_shift);
chip->cmdfunc(mtd, NAND_CMD_SEQIN, column, page);
chip->write_buf(mtd, block_mark, 1);
chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
status = chip->waitfunc(mtd, chip);
if (status & NAND_STATUS_FAIL)
ret = -EIO;
chip->select_chip(mtd, -1);
return ret;
}
static int nand_boot_set_geometry(struct gpmi_nand_data *this)
{
struct boot_rom_geometry *geometry = &this->rom_geometry;
/*
* Set the boot block stride size.
*
* In principle, we should be reading this from the OTP bits, since
* that's where the ROM is going to get it. In fact, we don't have any
* way to read the OTP bits, so we go with the default and hope for the
* best.
*/
geometry->stride_size_in_pages = 64;
/*
* Set the search area stride exponent.
*
* In principle, we should be reading this from the OTP bits, since
* that's where the ROM is going to get it. In fact, we don't have any
* way to read the OTP bits, so we go with the default and hope for the
* best.
*/
geometry->search_area_stride_exponent = 2;
return 0;
}
static const char *fingerprint = "STMP";
static int mx23_check_transcription_stamp(struct gpmi_nand_data *this)
{
struct boot_rom_geometry *rom_geo = &this->rom_geometry;
struct device *dev = this->dev;
struct mtd_info *mtd = &this->mtd;
struct nand_chip *chip = &this->nand;
unsigned int search_area_size_in_strides;
unsigned int stride;
unsigned int page;
uint8_t *buffer = chip->buffers->databuf;
int saved_chip_number;
int found_an_ncb_fingerprint = false;
/* Compute the number of strides in a search area. */
search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent;
saved_chip_number = this->current_chip;
chip->select_chip(mtd, 0);
/*
* Loop through the first search area, looking for the NCB fingerprint.
*/
dev_dbg(dev, "Scanning for an NCB fingerprint...\n");
for (stride = 0; stride < search_area_size_in_strides; stride++) {
/* Compute the page addresses. */
page = stride * rom_geo->stride_size_in_pages;
dev_dbg(dev, "Looking for a fingerprint in page 0x%x\n", page);
/*
* Read the NCB fingerprint. The fingerprint is four bytes long
* and starts in the 12th byte of the page.
*/
chip->cmdfunc(mtd, NAND_CMD_READ0, 12, page);
chip->read_buf(mtd, buffer, strlen(fingerprint));
/* Look for the fingerprint. */
if (!memcmp(buffer, fingerprint, strlen(fingerprint))) {
found_an_ncb_fingerprint = true;
break;
}
}
chip->select_chip(mtd, saved_chip_number);
if (found_an_ncb_fingerprint)
dev_dbg(dev, "\tFound a fingerprint\n");
else
dev_dbg(dev, "\tNo fingerprint found\n");
return found_an_ncb_fingerprint;
}
/* Writes a transcription stamp. */
static int mx23_write_transcription_stamp(struct gpmi_nand_data *this)
{
struct device *dev = this->dev;
struct boot_rom_geometry *rom_geo = &this->rom_geometry;
struct mtd_info *mtd = &this->mtd;
struct nand_chip *chip = &this->nand;
unsigned int block_size_in_pages;
unsigned int search_area_size_in_strides;
unsigned int search_area_size_in_pages;
unsigned int search_area_size_in_blocks;
unsigned int block;
unsigned int stride;
unsigned int page;
uint8_t *buffer = chip->buffers->databuf;
int saved_chip_number;
int status;
/* Compute the search area geometry. */
block_size_in_pages = mtd->erasesize / mtd->writesize;
search_area_size_in_strides = 1 << rom_geo->search_area_stride_exponent;
search_area_size_in_pages = search_area_size_in_strides *
rom_geo->stride_size_in_pages;
search_area_size_in_blocks =
(search_area_size_in_pages + (block_size_in_pages - 1)) /
block_size_in_pages;
dev_dbg(dev, "Search Area Geometry :\n");
dev_dbg(dev, "\tin Blocks : %u\n", search_area_size_in_blocks);
dev_dbg(dev, "\tin Strides: %u\n", search_area_size_in_strides);
dev_dbg(dev, "\tin Pages : %u\n", search_area_size_in_pages);
/* Select chip 0. */
saved_chip_number = this->current_chip;
chip->select_chip(mtd, 0);
/* Loop over blocks in the first search area, erasing them. */
dev_dbg(dev, "Erasing the search area...\n");
for (block = 0; block < search_area_size_in_blocks; block++) {
/* Compute the page address. */
page = block * block_size_in_pages;
/* Erase this block. */
dev_dbg(dev, "\tErasing block 0x%x\n", block);
chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
/* Wait for the erase to finish. */
status = chip->waitfunc(mtd, chip);
if (status & NAND_STATUS_FAIL)
dev_err(dev, "[%s] Erase failed.\n", __func__);
}
/* Write the NCB fingerprint into the page buffer. */
memset(buffer, ~0, mtd->writesize);
memcpy(buffer + 12, fingerprint, strlen(fingerprint));
/* Loop through the first search area, writing NCB fingerprints. */
dev_dbg(dev, "Writing NCB fingerprints...\n");
for (stride = 0; stride < search_area_size_in_strides; stride++) {
/* Compute the page addresses. */
page = stride * rom_geo->stride_size_in_pages;
/* Write the first page of the current stride. */
dev_dbg(dev, "Writing an NCB fingerprint in page 0x%x\n", page);
chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
chip->ecc.write_page_raw(mtd, chip, buffer, 0);
chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
/* Wait for the write to finish. */
status = chip->waitfunc(mtd, chip);
if (status & NAND_STATUS_FAIL)
dev_err(dev, "[%s] Write failed.\n", __func__);
}
/* Deselect chip 0. */
chip->select_chip(mtd, saved_chip_number);
return 0;
}
static int mx23_boot_init(struct gpmi_nand_data *this)
{
struct device *dev = this->dev;
struct nand_chip *chip = &this->nand;
struct mtd_info *mtd = &this->mtd;
unsigned int block_count;
unsigned int block;
int chipnr;
int page;
loff_t byte;
uint8_t block_mark;
int ret = 0;
/*
* If control arrives here, we can't use block mark swapping, which
* means we're forced to use transcription. First, scan for the
* transcription stamp. If we find it, then we don't have to do
* anything -- the block marks are already transcribed.
*/
if (mx23_check_transcription_stamp(this))
return 0;
/*
* If control arrives here, we couldn't find a transcription stamp, so
* so we presume the block marks are in the conventional location.
*/
dev_dbg(dev, "Transcribing bad block marks...\n");
/* Compute the number of blocks in the entire medium. */
block_count = chip->chipsize >> chip->phys_erase_shift;
/*
* Loop over all the blocks in the medium, transcribing block marks as
* we go.
*/
for (block = 0; block < block_count; block++) {
/*
* Compute the chip, page and byte addresses for this block's
* conventional mark.
*/
chipnr = block >> (chip->chip_shift - chip->phys_erase_shift);
page = block << (chip->phys_erase_shift - chip->page_shift);
byte = block << chip->phys_erase_shift;
/* Send the command to read the conventional block mark. */
chip->select_chip(mtd, chipnr);
chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page);
block_mark = chip->read_byte(mtd);
chip->select_chip(mtd, -1);
/*
* Check if the block is marked bad. If so, we need to mark it
* again, but this time the result will be a mark in the
* location where we transcribe block marks.
*/
if (block_mark != 0xff) {
dev_dbg(dev, "Transcribing mark in block %u\n", block);
ret = chip->block_markbad(mtd, byte);
if (ret)
dev_err(dev, "Failed to mark block bad with "
"ret %d\n", ret);
}
}
/* Write the stamp that indicates we've transcribed the block marks. */
mx23_write_transcription_stamp(this);
return 0;
}
static int nand_boot_init(struct gpmi_nand_data *this)
{
nand_boot_set_geometry(this);
/* This is ROM arch-specific initilization before the BBT scanning. */
if (GPMI_IS_MX23(this))
return mx23_boot_init(this);
return 0;
}
static int gpmi_set_geometry(struct gpmi_nand_data *this)
{
int ret;
/* Free the temporary DMA memory for reading ID. */
gpmi_free_dma_buffer(this);
/* Set up the NFC geometry which is used by BCH. */
ret = bch_set_geometry(this);
if (ret) {
dev_err(this->dev, "Error setting BCH geometry : %d\n", ret);
return ret;
}
/* Alloc the new DMA buffers according to the pagesize and oobsize */
return gpmi_alloc_dma_buffer(this);
}
static void gpmi_nand_exit(struct gpmi_nand_data *this)
{
nand_release(&this->mtd);
gpmi_free_dma_buffer(this);
}
static int gpmi_init_last(struct gpmi_nand_data *this)
{
struct mtd_info *mtd = &this->mtd;
struct nand_chip *chip = mtd->priv;
struct nand_ecc_ctrl *ecc = &chip->ecc;
struct bch_geometry *bch_geo = &this->bch_geometry;
int ret;
/* Set up swap_block_mark, must be set before the gpmi_set_geometry() */
this->swap_block_mark = !GPMI_IS_MX23(this);
/* Set up the medium geometry */
ret = gpmi_set_geometry(this);
if (ret)
return ret;
/* Init the nand_ecc_ctrl{} */
ecc->read_page = gpmi_ecc_read_page;
ecc->write_page = gpmi_ecc_write_page;
ecc->read_oob = gpmi_ecc_read_oob;
ecc->write_oob = gpmi_ecc_write_oob;
ecc->mode = NAND_ECC_HW;
ecc->size = bch_geo->ecc_chunk_size;
ecc->strength = bch_geo->ecc_strength;
ecc->layout = &gpmi_hw_ecclayout;
/*
* Can we enable the extra features? such as EDO or Sync mode.
*
* We do not check the return value now. That's means if we fail in
* enable the extra features, we still can run in the normal way.
*/
gpmi_extra_init(this);
return 0;
}
static int gpmi_nand_init(struct gpmi_nand_data *this)
{
struct mtd_info *mtd = &this->mtd;
struct nand_chip *chip = &this->nand;
struct mtd_part_parser_data ppdata = {};
int ret;
/* init current chip */
this->current_chip = -1;
/* init the MTD data structures */
mtd->priv = chip;
mtd->name = "gpmi-nand";
mtd->owner = THIS_MODULE;
/* init the nand_chip{}, we don't support a 16-bit NAND Flash bus. */
chip->priv = this;
chip->select_chip = gpmi_select_chip;
chip->cmd_ctrl = gpmi_cmd_ctrl;
chip->dev_ready = gpmi_dev_ready;
chip->read_byte = gpmi_read_byte;
chip->read_buf = gpmi_read_buf;
chip->write_buf = gpmi_write_buf;
chip->badblock_pattern = &gpmi_bbt_descr;
chip->block_markbad = gpmi_block_markbad;
chip->options |= NAND_NO_SUBPAGE_WRITE;
if (of_get_nand_on_flash_bbt(this->dev->of_node))
chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB;
/*
* Allocate a temporary DMA buffer for reading ID in the
* nand_scan_ident().
*/
this->bch_geometry.payload_size = 1024;
this->bch_geometry.auxiliary_size = 128;
ret = gpmi_alloc_dma_buffer(this);
if (ret)
goto err_out;
ret = nand_scan_ident(mtd, GPMI_IS_MX6Q(this) ? 2 : 1, NULL);
if (ret)
goto err_out;
ret = gpmi_init_last(this);
if (ret)
goto err_out;
chip->options |= NAND_SKIP_BBTSCAN;
ret = nand_scan_tail(mtd);
if (ret)
goto err_out;
ret = nand_boot_init(this);
if (ret)
goto err_out;
chip->scan_bbt(mtd);
ppdata.of_node = this->pdev->dev.of_node;
ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
if (ret)
goto err_out;
return 0;
err_out:
gpmi_nand_exit(this);
return ret;
}
static const struct platform_device_id gpmi_ids[] = {
{ .name = "imx23-gpmi-nand", .driver_data = IS_MX23, },
{ .name = "imx28-gpmi-nand", .driver_data = IS_MX28, },
{ .name = "imx6q-gpmi-nand", .driver_data = IS_MX6Q, },
{}
};
static const struct of_device_id gpmi_nand_id_table[] = {
{
.compatible = "fsl,imx23-gpmi-nand",
.data = (void *)&gpmi_ids[IS_MX23],
}, {
.compatible = "fsl,imx28-gpmi-nand",
.data = (void *)&gpmi_ids[IS_MX28],
}, {
.compatible = "fsl,imx6q-gpmi-nand",
.data = (void *)&gpmi_ids[IS_MX6Q],
}, {}
};
MODULE_DEVICE_TABLE(of, gpmi_nand_id_table);
static int gpmi_nand_probe(struct platform_device *pdev)
{
struct gpmi_nand_data *this;
const struct of_device_id *of_id;
int ret;
of_id = of_match_device(gpmi_nand_id_table, &pdev->dev);
if (of_id) {
pdev->id_entry = of_id->data;
} else {
dev_err(&pdev->dev, "Failed to find the right device id.\n");
return -ENODEV;
}
this = devm_kzalloc(&pdev->dev, sizeof(*this), GFP_KERNEL);
if (!this)
return -ENOMEM;
platform_set_drvdata(pdev, this);
this->pdev = pdev;
this->dev = &pdev->dev;
ret = acquire_resources(this);
if (ret)
goto exit_acquire_resources;
ret = init_hardware(this);
if (ret)
goto exit_nfc_init;
ret = gpmi_nand_init(this);
if (ret)
goto exit_nfc_init;
dev_info(this->dev, "driver registered.\n");
return 0;
exit_nfc_init:
release_resources(this);
exit_acquire_resources:
dev_err(this->dev, "driver registration failed: %d\n", ret);
return ret;
}
static int gpmi_nand_remove(struct platform_device *pdev)
{
struct gpmi_nand_data *this = platform_get_drvdata(pdev);
gpmi_nand_exit(this);
release_resources(this);
return 0;
}
static struct platform_driver gpmi_nand_driver = {
.driver = {
.name = "gpmi-nand",
.of_match_table = gpmi_nand_id_table,
},
.probe = gpmi_nand_probe,
.remove = gpmi_nand_remove,
.id_table = gpmi_ids,
};
module_platform_driver(gpmi_nand_driver);
MODULE_AUTHOR("Freescale Semiconductor, Inc.");
MODULE_DESCRIPTION("i.MX GPMI NAND Flash Controller Driver");
MODULE_LICENSE("GPL");