- 根目录:
- drivers
- staging
- cxt1e1
- pmc93x6_eeprom.c
/* pmc93x6_eeprom.c - PMC's 93LC46 EEPROM Device
*
* The 93LC46 is a low-power, serial Electrically Erasable and
* Programmable Read Only Memory organized as 128 8-bit bytes.
*
* Accesses to the 93LC46 are done in a bit serial stream, organized
* in a 3 wire format. Writes are internally timed by the device
* (the In data bit is pulled low until the write is complete and
* then is pulled high) and take about 6 milliseconds.
*
* Copyright (C) 2003-2005 SBE, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/types.h>
#include "pmcc4_sysdep.h"
#include "sbecom_inline_linux.h"
#include "pmcc4.h"
#include "sbe_promformat.h"
#ifndef TRUE
#define TRUE 1
#define FALSE 0
#endif
/*------------------------------------------------------------------------
* EEPROM address definitions
*------------------------------------------------------------------------
*
* The offset in the definitions below allows the test to skip over
* areas of the EEPROM that other programs (such a VxWorks) are
* using.
*/
#define EE_MFG (long)0 /* Index to manufacturing record */
#define EE_FIRST 0x28 /* Index to start testing at */
#define EE_LIMIT 128 /* Index to end testing at */
/* Bit Ordering for Instructions
**
** A0, A1, A2, A3, A4, A5, A6, OP0, OP1, SB (lsb, or 1st bit out)
**
*/
#define EPROM_EWEN 0x0019 /* Erase/Write enable (reversed) */
#define EPROM_EWDS 0x0001 /* Erase/Write disable (reversed) */
#define EPROM_READ 0x0003 /* Read (reversed) */
#define EPROM_WRITE 0x0005 /* Write (reversed) */
#define EPROM_ERASE 0x0007 /* Erase (reversed) */
#define EPROM_ERAL 0x0009 /* Erase All (reversed) */
#define EPROM_WRAL 0x0011 /* Write All (reversed) */
#define EPROM_ADR_SZ 7 /* Number of bits in offset address */
#define EPROM_OP_SZ 3 /* Number of bits in command */
#define SIZE_ADDR_OP (EPROM_ADR_SZ + EPROM_OP_SZ)
#define LC46A_MAX_OPS 10 /* Number of bits in Instruction */
#define NUM_OF_BITS 8 /* Number of bits in data */
/* EEPROM signal bits */
#define EPROM_ACTIVE_OUT_BIT 0x0001 /* Out data bit */
#define EPROM_ACTIVE_IN_BIT 0x0002 /* In data bit */
#define ACTIVE_IN_BIT_SHIFT 0x0001 /* Shift In data bit to LSB */
#define EPROM_ENCS 0x0004 /* Set EEPROM CS during operation */
/*------------------------------------------------------------------------
* The ByteReverse table is used to reverses the 8 bits within a byte
*------------------------------------------------------------------------
*/
static unsigned char ByteReverse[256];
static int ByteReverseBuilt = FALSE;
/*------------------------------------------------------------------------
* mfg_template - initial serial EEPROM data structure
*------------------------------------------------------------------------
*/
short mfg_template[sizeof (FLD_TYPE2)] =
{
PROM_FORMAT_TYPE2, /* type; */
0x00, 0x1A, /* length[2]; */
0x00, 0x00, 0x00, 0x00, /* Crc32[4]; */
0x11, 0x76, /* Id[2]; */
0x07, 0x05, /* SubId[2] E1; */
0x00, 0xA0, 0xD6, 0x00, 0x00, 0x00, /* Serial[6]; */
0x00, 0x00, 0x00, 0x00, /* CreateTime[4]; */
0x00, 0x00, 0x00, 0x00, /* HeatRunTime[4]; */
0x00, 0x00, 0x00, 0x00, /* HeatRunIterations[4]; */
0x00, 0x00, 0x00, 0x00, /* HeatRunErrors[4]; */
};
/*------------------------------------------------------------------------
* BuildByteReverse - build the 8-bit reverse table
*------------------------------------------------------------------------
*
* The 'ByteReverse' table reverses the 8 bits within a byte
* (the MSB becomes the LSB etc.).
*/
static void
BuildByteReverse (void)
{
long half; /* Used to build by powers to 2 */
int i;
ByteReverse[0] = 0;
for (half = 1; half < sizeof (ByteReverse); half <<= 1)
for (i = 0; i < half; i++)
ByteReverse[half + i] = (char) (ByteReverse[i] | (0x80 / half));
ByteReverseBuilt = TRUE;
}
/*------------------------------------------------------------------------
* eeprom_delay - small delay for EEPROM timing
*------------------------------------------------------------------------
*/
static void
eeprom_delay (void)
{
int timeout;
for (timeout = 20; timeout; --timeout)
{
OS_uwait_dummy ();
}
}
/*------------------------------------------------------------------------
* eeprom_put_byte - Send a byte to the EEPROM serially
*------------------------------------------------------------------------
*
* Given the PCI address and the data, this routine serially sends
* the data to the EEPROM.
*/
void
eeprom_put_byte (long addr, long data, int count)
{
u_int32_t output;
while (--count >= 0)
{
output = (data & EPROM_ACTIVE_OUT_BIT) ? 1 : 0; /* Get next data bit */
output |= EPROM_ENCS; /* Add Chip Select */
data >>= 1;
eeprom_delay ();
pci_write_32 ((u_int32_t *) addr, output); /* Output it */
}
}
/*------------------------------------------------------------------------
* eeprom_get_byte - Receive a byte from the EEPROM serially
*------------------------------------------------------------------------
*
* Given the PCI address, this routine serially fetches the data
* from the EEPROM.
*/
u_int32_t
eeprom_get_byte (long addr)
{
u_int32_t input;
u_int32_t data;
int count;
/* Start the Reading of DATA
**
** The first read is a dummy as the data is latched in the
** EPLD and read on the next read access to the EEPROM.
*/
input = pci_read_32 ((u_int32_t *) addr);
data = 0;
count = NUM_OF_BITS;
while (--count >= 0)
{
eeprom_delay ();
input = pci_read_32 ((u_int32_t *) addr);
data <<= 1; /* Shift data over */
data |= (input & EPROM_ACTIVE_IN_BIT) ? 1 : 0;
}
return data;
}
/*------------------------------------------------------------------------
* disable_pmc_eeprom - Disable writes to the EEPROM
*------------------------------------------------------------------------
*
* Issue the EEPROM command to disable writes.
*/
static void
disable_pmc_eeprom (long addr)
{
eeprom_put_byte (addr, EPROM_EWDS, SIZE_ADDR_OP);
pci_write_32 ((u_int32_t *) addr, 0); /* this removes Chip Select
* from EEPROM */
}
/*------------------------------------------------------------------------
* enable_pmc_eeprom - Enable writes to the EEPROM
*------------------------------------------------------------------------
*
* Issue the EEPROM command to enable writes.
*/
static void
enable_pmc_eeprom (long addr)
{
eeprom_put_byte (addr, EPROM_EWEN, SIZE_ADDR_OP);
pci_write_32 ((u_int32_t *) addr, 0); /* this removes Chip Select
* from EEPROM */
}
/*------------------------------------------------------------------------
* pmc_eeprom_read - EEPROM location read
*------------------------------------------------------------------------
*
* Given a EEPROM PCI address and location offset, this routine returns
* the contents of the specified location to the calling routine.
*/
u_int32_t
pmc_eeprom_read (long addr, long mem_offset)
{
u_int32_t data; /* Data from chip */
if (!ByteReverseBuilt)
BuildByteReverse ();
mem_offset = ByteReverse[0x7F & mem_offset]; /* Reverse address */
/*
* NOTE: The max offset address is 128 or half the reversal table. So the
* LSB is always zero and counts as a built in shift of one bit. So even
* though we need to shift 3 bits to make room for the command, we only
* need to shift twice more because of the built in shift.
*/
mem_offset <<= 2; /* Shift for command */
mem_offset |= EPROM_READ; /* Add command */
eeprom_put_byte (addr, mem_offset, SIZE_ADDR_OP); /* Output chip address */
data = eeprom_get_byte (addr); /* Read chip data */
pci_write_32 ((u_int32_t *) addr, 0); /* Remove Chip Select from
* EEPROM */
return (data & 0x000000FF);
}
/*------------------------------------------------------------------------
* pmc_eeprom_write - EEPROM location write
*------------------------------------------------------------------------
*
* Given a EEPROM PCI address, location offset and value, this
* routine writes the value to the specified location.
*
* Note: it is up to the caller to determine if the write
* operation succeeded.
*/
int
pmc_eeprom_write (long addr, long mem_offset, u_int32_t data)
{
volatile u_int32_t temp;
int count;
if (!ByteReverseBuilt)
BuildByteReverse ();
mem_offset = ByteReverse[0x7F & mem_offset]; /* Reverse address */
/*
* NOTE: The max offset address is 128 or half the reversal table. So the
* LSB is always zero and counts as a built in shift of one bit. So even
* though we need to shift 3 bits to make room for the command, we only
* need to shift twice more because of the built in shift.
*/
mem_offset <<= 2; /* Shift for command */
mem_offset |= EPROM_WRITE; /* Add command */
eeprom_put_byte (addr, mem_offset, SIZE_ADDR_OP); /* Output chip address */
data = ByteReverse[0xFF & data];/* Reverse data */
eeprom_put_byte (addr, data, NUM_OF_BITS); /* Output chip data */
pci_write_32 ((u_int32_t *) addr, 0); /* Remove Chip Select from
* EEPROM */
/*
** Must see Data In at a low state before completing this transaction.
**
** Afterwards, the data bit will return to a high state, ~6 ms, terminating
** the operation.
*/
pci_write_32 ((u_int32_t *) addr, EPROM_ENCS); /* Re-enable Chip Select */
temp = pci_read_32 ((u_int32_t *) addr); /* discard first read */
temp = pci_read_32 ((u_int32_t *) addr);
if (temp & EPROM_ACTIVE_IN_BIT)
{
temp = pci_read_32 ((u_int32_t *) addr);
if (temp & EPROM_ACTIVE_IN_BIT)
{
pci_write_32 ((u_int32_t *) addr, 0); /* Remove Chip Select
* from EEPROM */
return (1);
}
}
count = 1000;
while (count--)
{
for (temp = 0; temp < 0x10; temp++)
OS_uwait_dummy ();
if (pci_read_32 ((u_int32_t *) addr) & EPROM_ACTIVE_IN_BIT)
break;
}
if (count == -1)
return (2);
return (0);
}
/*------------------------------------------------------------------------
* pmcGetBuffValue - read the specified value from buffer
*------------------------------------------------------------------------
*/
long
pmcGetBuffValue (char *ptr, int size)
{
long value = 0;
int index;
for (index = 0; index < size; ++index)
{
value <<= 8;
value |= ptr[index] & 0xFF;
}
return value;
}
/*------------------------------------------------------------------------
* pmcSetBuffValue - save the specified value to buffer
*------------------------------------------------------------------------
*/
void
pmcSetBuffValue (char *ptr, long value, int size)
{
int index = size;
while (--index >= 0)
{
ptr[index] = (char) (value & 0xFF);
value >>= 8;
}
}
/*------------------------------------------------------------------------
* pmc_eeprom_read_buffer - read EEPROM data into specified buffer
*------------------------------------------------------------------------
*/
void
pmc_eeprom_read_buffer (long addr, long mem_offset, char *dest_ptr, int size)
{
while (--size >= 0)
*dest_ptr++ = (char) pmc_eeprom_read (addr, mem_offset++);
}
/*------------------------------------------------------------------------
* pmc_eeprom_write_buffer - write EEPROM data from specified buffer
*------------------------------------------------------------------------
*/
void
pmc_eeprom_write_buffer (long addr, long mem_offset, char *dest_ptr, int size)
{
enable_pmc_eeprom (addr);
while (--size >= 0)
pmc_eeprom_write (addr, mem_offset++, *dest_ptr++);
disable_pmc_eeprom (addr);
}
/*------------------------------------------------------------------------
* pmcCalcCrc - calculate the CRC for the serial EEPROM structure
*------------------------------------------------------------------------
*/
u_int32_t
pmcCalcCrc_T01 (void *bufp)
{
FLD_TYPE2 *buf = bufp;
u_int32_t crc; /* CRC of the structure */
/* Calc CRC for type and length fields */
sbeCrc (
(u_int8_t *) &buf->type,
(u_int32_t) STRUCT_OFFSET (FLD_TYPE1, Crc32),
(u_int32_t) 0,
(u_int32_t *) &crc);
#ifdef EEPROM_TYPE_DEBUG
pr_info("sbeCrc: crc 1 calculated as %08x\n", crc); /* RLD DEBUG */
#endif
return ~crc;
}
u_int32_t
pmcCalcCrc_T02 (void *bufp)
{
FLD_TYPE2 *buf = bufp;
u_int32_t crc; /* CRC of the structure */
/* Calc CRC for type and length fields */
sbeCrc (
(u_int8_t *) &buf->type,
(u_int32_t) STRUCT_OFFSET (FLD_TYPE2, Crc32),
(u_int32_t) 0,
(u_int32_t *) &crc);
/* Calc CRC for remaining fields */
sbeCrc (
(u_int8_t *) &buf->Id[0],
(u_int32_t) (sizeof (FLD_TYPE2) - STRUCT_OFFSET (FLD_TYPE2, Id)),
(u_int32_t) crc,
(u_int32_t *) &crc);
#ifdef EEPROM_TYPE_DEBUG
pr_info("sbeCrc: crc 2 calculated as %08x\n", crc); /* RLD DEBUG */
#endif
return crc;
}
/*------------------------------------------------------------------------
* pmc_init_seeprom - initialize the serial EEPROM structure
*------------------------------------------------------------------------
*
* At the front of the serial EEPROM there is a record that contains
* manufacturing information. If the info does not already exist, it
* is created. The only field modifiable by the operator is the
* serial number field.
*/
void
pmc_init_seeprom (u_int32_t addr, u_int32_t serialNum)
{
PROMFORMAT buffer; /* Memory image of structure */
u_int32_t crc; /* CRC of structure */
time_t createTime;
int i;
createTime = get_seconds ();
/* use template data */
for (i = 0; i < sizeof (FLD_TYPE2); ++i)
buffer.bytes[i] = mfg_template[i];
/* Update serial number field in buffer */
pmcSetBuffValue (&buffer.fldType2.Serial[3], serialNum, 3);
/* Update create time field in buffer */
pmcSetBuffValue (&buffer.fldType2.CreateTime[0], createTime, 4);
/* Update CRC field in buffer */
crc = pmcCalcCrc_T02 (&buffer);
pmcSetBuffValue (&buffer.fldType2.Crc32[0], crc, 4);
#ifdef DEBUG
for (i = 0; i < sizeof (FLD_TYPE2); ++i)
pr_info("[%02X] = %02X\n", i, buffer.bytes[i] & 0xFF);
#endif
/* Write structure to serial EEPROM */
pmc_eeprom_write_buffer (addr, EE_MFG, (char *) &buffer, sizeof (FLD_TYPE2));
}
char
pmc_verify_cksum (void *bufp)
{
FLD_TYPE1 *buf1 = bufp;
FLD_TYPE2 *buf2 = bufp;
u_int32_t crc1, crc2; /* CRC read from EEPROM */
/* Retrieve contents of CRC field */
crc1 = pmcGetBuffValue (&buf1->Crc32[0], sizeof (buf1->Crc32));
#ifdef EEPROM_TYPE_DEBUG
pr_info("EEPROM: chksum 1 reads as %08x\n", crc1); /* RLD DEBUG */
#endif
if ((buf1->type == PROM_FORMAT_TYPE1) &&
(pmcCalcCrc_T01 ((void *) buf1) == crc1))
return PROM_FORMAT_TYPE1; /* checksum type 1 verified */
crc2 = pmcGetBuffValue (&buf2->Crc32[0], sizeof (buf2->Crc32));
#ifdef EEPROM_TYPE_DEBUG
pr_info("EEPROM: chksum 2 reads as %08x\n", crc2); /* RLD DEBUG */
#endif
if ((buf2->type == PROM_FORMAT_TYPE2) &&
(pmcCalcCrc_T02 ((void *) buf2) == crc2))
return PROM_FORMAT_TYPE2; /* checksum type 2 verified */
return PROM_FORMAT_Unk; /* failed to validate */
}
/*** End-of-File ***/