/*
* linux/drivers/net/irda/sa1100_ir.c
*
* Copyright (C) 2000-2001 Russell King
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Infra-red driver for the StrongARM SA1100 embedded microprocessor
*
* Note that we don't have to worry about the SA1111's DMA bugs in here,
* so we use the straight forward dma_map_* functions with a null pointer.
*
* This driver takes one kernel command line parameter, sa1100ir=, with
* the following options:
* max_rate:baudrate - set the maximum baud rate
* power_leve:level - set the transmitter power level
* tx_lpm:0|1 - set transmit low power mode
*/
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/netdevice.h>
#include <linux/slab.h>
#include <linux/rtnetlink.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <net/irda/irda.h>
#include <net/irda/wrapper.h>
#include <net/irda/irda_device.h>
#include <asm/irq.h>
#include <mach/dma.h>
#include <mach/hardware.h>
#include <asm/mach/irda.h>
static int power_level = 3;
static int tx_lpm;
static int max_rate = 4000000;
struct sa1100_irda {
unsigned char hscr0;
unsigned char utcr4;
unsigned char power;
unsigned char open;
int speed;
int newspeed;
struct sk_buff *txskb;
struct sk_buff *rxskb;
dma_addr_t txbuf_dma;
dma_addr_t rxbuf_dma;
dma_regs_t *txdma;
dma_regs_t *rxdma;
struct device *dev;
struct irda_platform_data *pdata;
struct irlap_cb *irlap;
struct qos_info qos;
iobuff_t tx_buff;
iobuff_t rx_buff;
};
#define IS_FIR(si) ((si)->speed >= 4000000)
#define HPSIR_MAX_RXLEN 2047
/*
* Allocate and map the receive buffer, unless it is already allocated.
*/
static int sa1100_irda_rx_alloc(struct sa1100_irda *si)
{
if (si->rxskb)
return 0;
si->rxskb = alloc_skb(HPSIR_MAX_RXLEN + 1, GFP_ATOMIC);
if (!si->rxskb) {
printk(KERN_ERR "sa1100_ir: out of memory for RX SKB\n");
return -ENOMEM;
}
/*
* Align any IP headers that may be contained
* within the frame.
*/
skb_reserve(si->rxskb, 1);
si->rxbuf_dma = dma_map_single(si->dev, si->rxskb->data,
HPSIR_MAX_RXLEN,
DMA_FROM_DEVICE);
return 0;
}
/*
* We want to get here as soon as possible, and get the receiver setup.
* We use the existing buffer.
*/
static void sa1100_irda_rx_dma_start(struct sa1100_irda *si)
{
if (!si->rxskb) {
printk(KERN_ERR "sa1100_ir: rx buffer went missing\n");
return;
}
/*
* First empty receive FIFO
*/
Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
/*
* Enable the DMA, receiver and receive interrupt.
*/
sa1100_clear_dma(si->rxdma);
sa1100_start_dma(si->rxdma, si->rxbuf_dma, HPSIR_MAX_RXLEN);
Ser2HSCR0 = si->hscr0 | HSCR0_HSSP | HSCR0_RXE;
}
/*
* Set the IrDA communications speed.
*/
static int sa1100_irda_set_speed(struct sa1100_irda *si, int speed)
{
unsigned long flags;
int brd, ret = -EINVAL;
switch (speed) {
case 9600: case 19200: case 38400:
case 57600: case 115200:
brd = 3686400 / (16 * speed) - 1;
/*
* Stop the receive DMA.
*/
if (IS_FIR(si))
sa1100_stop_dma(si->rxdma);
local_irq_save(flags);
Ser2UTCR3 = 0;
Ser2HSCR0 = HSCR0_UART;
Ser2UTCR1 = brd >> 8;
Ser2UTCR2 = brd;
/*
* Clear status register
*/
Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE;
if (si->pdata->set_speed)
si->pdata->set_speed(si->dev, speed);
si->speed = speed;
local_irq_restore(flags);
ret = 0;
break;
case 4000000:
local_irq_save(flags);
si->hscr0 = 0;
Ser2HSSR0 = 0xff;
Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
Ser2UTCR3 = 0;
si->speed = speed;
if (si->pdata->set_speed)
si->pdata->set_speed(si->dev, speed);
sa1100_irda_rx_alloc(si);
sa1100_irda_rx_dma_start(si);
local_irq_restore(flags);
break;
default:
break;
}
return ret;
}
/*
* Control the power state of the IrDA transmitter.
* State:
* 0 - off
* 1 - short range, lowest power
* 2 - medium range, medium power
* 3 - maximum range, high power
*
* Currently, only assabet is known to support this.
*/
static int
__sa1100_irda_set_power(struct sa1100_irda *si, unsigned int state)
{
int ret = 0;
if (si->pdata->set_power)
ret = si->pdata->set_power(si->dev, state);
return ret;
}
static inline int
sa1100_set_power(struct sa1100_irda *si, unsigned int state)
{
int ret;
ret = __sa1100_irda_set_power(si, state);
if (ret == 0)
si->power = state;
return ret;
}
static int sa1100_irda_startup(struct sa1100_irda *si)
{
int ret;
/*
* Ensure that the ports for this device are setup correctly.
*/
if (si->pdata->startup) {
ret = si->pdata->startup(si->dev);
if (ret)
return ret;
}
/*
* Configure PPC for IRDA - we want to drive TXD2 low.
* We also want to drive this pin low during sleep.
*/
PPSR &= ~PPC_TXD2;
PSDR &= ~PPC_TXD2;
PPDR |= PPC_TXD2;
/*
* Enable HP-SIR modulation, and ensure that the port is disabled.
*/
Ser2UTCR3 = 0;
Ser2HSCR0 = HSCR0_UART;
Ser2UTCR4 = si->utcr4;
Ser2UTCR0 = UTCR0_8BitData;
Ser2HSCR2 = HSCR2_TrDataH | HSCR2_RcDataL;
/*
* Clear status register
*/
Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
ret = sa1100_irda_set_speed(si, si->speed = 9600);
if (ret) {
Ser2UTCR3 = 0;
Ser2HSCR0 = 0;
if (si->pdata->shutdown)
si->pdata->shutdown(si->dev);
}
return ret;
}
static void sa1100_irda_shutdown(struct sa1100_irda *si)
{
/*
* Stop all DMA activity.
*/
sa1100_stop_dma(si->rxdma);
sa1100_stop_dma(si->txdma);
/* Disable the port. */
Ser2UTCR3 = 0;
Ser2HSCR0 = 0;
if (si->pdata->shutdown)
si->pdata->shutdown(si->dev);
}
#ifdef CONFIG_PM
/*
* Suspend the IrDA interface.
*/
static int sa1100_irda_suspend(struct platform_device *pdev, pm_message_t state)
{
struct net_device *dev = platform_get_drvdata(pdev);
struct sa1100_irda *si;
if (!dev)
return 0;
si = netdev_priv(dev);
if (si->open) {
/*
* Stop the transmit queue
*/
netif_device_detach(dev);
disable_irq(dev->irq);
sa1100_irda_shutdown(si);
__sa1100_irda_set_power(si, 0);
}
return 0;
}
/*
* Resume the IrDA interface.
*/
static int sa1100_irda_resume(struct platform_device *pdev)
{
struct net_device *dev = platform_get_drvdata(pdev);
struct sa1100_irda *si;
if (!dev)
return 0;
si = netdev_priv(dev);
if (si->open) {
/*
* If we missed a speed change, initialise at the new speed
* directly. It is debatable whether this is actually
* required, but in the interests of continuing from where
* we left off it is desirable. The converse argument is
* that we should re-negotiate at 9600 baud again.
*/
if (si->newspeed) {
si->speed = si->newspeed;
si->newspeed = 0;
}
sa1100_irda_startup(si);
__sa1100_irda_set_power(si, si->power);
enable_irq(dev->irq);
/*
* This automatically wakes up the queue
*/
netif_device_attach(dev);
}
return 0;
}
#else
#define sa1100_irda_suspend NULL
#define sa1100_irda_resume NULL
#endif
/*
* HP-SIR format interrupt service routines.
*/
static void sa1100_irda_hpsir_irq(struct net_device *dev)
{
struct sa1100_irda *si = netdev_priv(dev);
int status;
status = Ser2UTSR0;
/*
* Deal with any receive errors first. The bytes in error may be
* the only bytes in the receive FIFO, so we do this first.
*/
while (status & UTSR0_EIF) {
int stat, data;
stat = Ser2UTSR1;
data = Ser2UTDR;
if (stat & (UTSR1_FRE | UTSR1_ROR)) {
dev->stats.rx_errors++;
if (stat & UTSR1_FRE)
dev->stats.rx_frame_errors++;
if (stat & UTSR1_ROR)
dev->stats.rx_fifo_errors++;
} else
async_unwrap_char(dev, &dev->stats, &si->rx_buff, data);
status = Ser2UTSR0;
}
/*
* We must clear certain bits.
*/
Ser2UTSR0 = status & (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
if (status & UTSR0_RFS) {
/*
* There are at least 4 bytes in the FIFO. Read 3 bytes
* and leave the rest to the block below.
*/
async_unwrap_char(dev, &dev->stats, &si->rx_buff, Ser2UTDR);
async_unwrap_char(dev, &dev->stats, &si->rx_buff, Ser2UTDR);
async_unwrap_char(dev, &dev->stats, &si->rx_buff, Ser2UTDR);
}
if (status & (UTSR0_RFS | UTSR0_RID)) {
/*
* Fifo contains more than 1 character.
*/
do {
async_unwrap_char(dev, &dev->stats, &si->rx_buff,
Ser2UTDR);
} while (Ser2UTSR1 & UTSR1_RNE);
}
if (status & UTSR0_TFS && si->tx_buff.len) {
/*
* Transmitter FIFO is not full
*/
do {
Ser2UTDR = *si->tx_buff.data++;
si->tx_buff.len -= 1;
} while (Ser2UTSR1 & UTSR1_TNF && si->tx_buff.len);
if (si->tx_buff.len == 0) {
dev->stats.tx_packets++;
dev->stats.tx_bytes += si->tx_buff.data -
si->tx_buff.head;
/*
* We need to ensure that the transmitter has
* finished.
*/
do
rmb();
while (Ser2UTSR1 & UTSR1_TBY);
/*
* Ok, we've finished transmitting. Now enable
* the receiver. Sometimes we get a receive IRQ
* immediately after a transmit...
*/
Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE;
if (si->newspeed) {
sa1100_irda_set_speed(si, si->newspeed);
si->newspeed = 0;
}
/* I'm hungry! */
netif_wake_queue(dev);
}
}
}
static void sa1100_irda_fir_error(struct sa1100_irda *si, struct net_device *dev)
{
struct sk_buff *skb = si->rxskb;
dma_addr_t dma_addr;
unsigned int len, stat, data;
if (!skb) {
printk(KERN_ERR "sa1100_ir: SKB is NULL!\n");
return;
}
/*
* Get the current data position.
*/
dma_addr = sa1100_get_dma_pos(si->rxdma);
len = dma_addr - si->rxbuf_dma;
if (len > HPSIR_MAX_RXLEN)
len = HPSIR_MAX_RXLEN;
dma_unmap_single(si->dev, si->rxbuf_dma, len, DMA_FROM_DEVICE);
do {
/*
* Read Status, and then Data.
*/
stat = Ser2HSSR1;
rmb();
data = Ser2HSDR;
if (stat & (HSSR1_CRE | HSSR1_ROR)) {
dev->stats.rx_errors++;
if (stat & HSSR1_CRE)
dev->stats.rx_crc_errors++;
if (stat & HSSR1_ROR)
dev->stats.rx_frame_errors++;
} else
skb->data[len++] = data;
/*
* If we hit the end of frame, there's
* no point in continuing.
*/
if (stat & HSSR1_EOF)
break;
} while (Ser2HSSR0 & HSSR0_EIF);
if (stat & HSSR1_EOF) {
si->rxskb = NULL;
skb_put(skb, len);
skb->dev = dev;
skb_reset_mac_header(skb);
skb->protocol = htons(ETH_P_IRDA);
dev->stats.rx_packets++;
dev->stats.rx_bytes += len;
/*
* Before we pass the buffer up, allocate a new one.
*/
sa1100_irda_rx_alloc(si);
netif_rx(skb);
} else {
/*
* Remap the buffer.
*/
si->rxbuf_dma = dma_map_single(si->dev, si->rxskb->data,
HPSIR_MAX_RXLEN,
DMA_FROM_DEVICE);
}
}
/*
* FIR format interrupt service routine. We only have to
* handle RX events; transmit events go via the TX DMA handler.
*
* No matter what, we disable RX, process, and the restart RX.
*/
static void sa1100_irda_fir_irq(struct net_device *dev)
{
struct sa1100_irda *si = netdev_priv(dev);
/*
* Stop RX DMA
*/
sa1100_stop_dma(si->rxdma);
/*
* Framing error - we throw away the packet completely.
* Clearing RXE flushes the error conditions and data
* from the fifo.
*/
if (Ser2HSSR0 & (HSSR0_FRE | HSSR0_RAB)) {
dev->stats.rx_errors++;
if (Ser2HSSR0 & HSSR0_FRE)
dev->stats.rx_frame_errors++;
/*
* Clear out the DMA...
*/
Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
/*
* Clear selected status bits now, so we
* don't miss them next time around.
*/
Ser2HSSR0 = HSSR0_FRE | HSSR0_RAB;
}
/*
* Deal with any receive errors. The any of the lowest
* 8 bytes in the FIFO may contain an error. We must read
* them one by one. The "error" could even be the end of
* packet!
*/
if (Ser2HSSR0 & HSSR0_EIF)
sa1100_irda_fir_error(si, dev);
/*
* No matter what happens, we must restart reception.
*/
sa1100_irda_rx_dma_start(si);
}
static irqreturn_t sa1100_irda_irq(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
if (IS_FIR(((struct sa1100_irda *)netdev_priv(dev))))
sa1100_irda_fir_irq(dev);
else
sa1100_irda_hpsir_irq(dev);
return IRQ_HANDLED;
}
/*
* TX DMA completion handler.
*/
static void sa1100_irda_txdma_irq(void *id)
{
struct net_device *dev = id;
struct sa1100_irda *si = netdev_priv(dev);
struct sk_buff *skb = si->txskb;
si->txskb = NULL;
/*
* Wait for the transmission to complete. Unfortunately,
* the hardware doesn't give us an interrupt to indicate
* "end of frame".
*/
do
rmb();
while (!(Ser2HSSR0 & HSSR0_TUR) || Ser2HSSR1 & HSSR1_TBY);
/*
* Clear the transmit underrun bit.
*/
Ser2HSSR0 = HSSR0_TUR;
/*
* Do we need to change speed? Note that we're lazy
* here - we don't free the old rxskb. We don't need
* to allocate a buffer either.
*/
if (si->newspeed) {
sa1100_irda_set_speed(si, si->newspeed);
si->newspeed = 0;
}
/*
* Start reception. This disables the transmitter for
* us. This will be using the existing RX buffer.
*/
sa1100_irda_rx_dma_start(si);
/*
* Account and free the packet.
*/
if (skb) {
dma_unmap_single(si->dev, si->txbuf_dma, skb->len, DMA_TO_DEVICE);
dev->stats.tx_packets ++;
dev->stats.tx_bytes += skb->len;
dev_kfree_skb_irq(skb);
}
/*
* Make sure that the TX queue is available for sending
* (for retries). TX has priority over RX at all times.
*/
netif_wake_queue(dev);
}
static int sa1100_irda_hard_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct sa1100_irda *si = netdev_priv(dev);
int speed = irda_get_next_speed(skb);
/*
* Does this packet contain a request to change the interface
* speed? If so, remember it until we complete the transmission
* of this frame.
*/
if (speed != si->speed && speed != -1)
si->newspeed = speed;
/*
* If this is an empty frame, we can bypass a lot.
*/
if (skb->len == 0) {
if (si->newspeed) {
si->newspeed = 0;
sa1100_irda_set_speed(si, speed);
}
dev_kfree_skb(skb);
return NETDEV_TX_OK;
}
if (!IS_FIR(si)) {
netif_stop_queue(dev);
si->tx_buff.data = si->tx_buff.head;
si->tx_buff.len = async_wrap_skb(skb, si->tx_buff.data,
si->tx_buff.truesize);
/*
* Set the transmit interrupt enable. This will fire
* off an interrupt immediately. Note that we disable
* the receiver so we won't get spurious characteres
* received.
*/
Ser2UTCR3 = UTCR3_TIE | UTCR3_TXE;
dev_kfree_skb(skb);
} else {
int mtt = irda_get_mtt(skb);
/*
* We must not be transmitting...
*/
BUG_ON(si->txskb);
netif_stop_queue(dev);
si->txskb = skb;
si->txbuf_dma = dma_map_single(si->dev, skb->data,
skb->len, DMA_TO_DEVICE);
sa1100_start_dma(si->txdma, si->txbuf_dma, skb->len);
/*
* If we have a mean turn-around time, impose the specified
* specified delay. We could shorten this by timing from
* the point we received the packet.
*/
if (mtt)
udelay(mtt);
Ser2HSCR0 = si->hscr0 | HSCR0_HSSP | HSCR0_TXE;
}
return NETDEV_TX_OK;
}
static int
sa1100_irda_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd)
{
struct if_irda_req *rq = (struct if_irda_req *)ifreq;
struct sa1100_irda *si = netdev_priv(dev);
int ret = -EOPNOTSUPP;
switch (cmd) {
case SIOCSBANDWIDTH:
if (capable(CAP_NET_ADMIN)) {
/*
* We are unable to set the speed if the
* device is not running.
*/
if (si->open) {
ret = sa1100_irda_set_speed(si,
rq->ifr_baudrate);
} else {
printk("sa1100_irda_ioctl: SIOCSBANDWIDTH: !netif_running\n");
ret = 0;
}
}
break;
case SIOCSMEDIABUSY:
ret = -EPERM;
if (capable(CAP_NET_ADMIN)) {
irda_device_set_media_busy(dev, TRUE);
ret = 0;
}
break;
case SIOCGRECEIVING:
rq->ifr_receiving = IS_FIR(si) ? 0
: si->rx_buff.state != OUTSIDE_FRAME;
break;
default:
break;
}
return ret;
}
static int sa1100_irda_start(struct net_device *dev)
{
struct sa1100_irda *si = netdev_priv(dev);
int err;
si->speed = 9600;
err = request_irq(dev->irq, sa1100_irda_irq, 0, dev->name, dev);
if (err)
goto err_irq;
err = sa1100_request_dma(DMA_Ser2HSSPRd, "IrDA receive",
NULL, NULL, &si->rxdma);
if (err)
goto err_rx_dma;
err = sa1100_request_dma(DMA_Ser2HSSPWr, "IrDA transmit",
sa1100_irda_txdma_irq, dev, &si->txdma);
if (err)
goto err_tx_dma;
/*
* The interrupt must remain disabled for now.
*/
disable_irq(dev->irq);
/*
* Setup the serial port for the specified speed.
*/
err = sa1100_irda_startup(si);
if (err)
goto err_startup;
/*
* Open a new IrLAP layer instance.
*/
si->irlap = irlap_open(dev, &si->qos, "sa1100");
err = -ENOMEM;
if (!si->irlap)
goto err_irlap;
/*
* Now enable the interrupt and start the queue
*/
si->open = 1;
sa1100_set_power(si, power_level); /* low power mode */
enable_irq(dev->irq);
netif_start_queue(dev);
return 0;
err_irlap:
si->open = 0;
sa1100_irda_shutdown(si);
err_startup:
sa1100_free_dma(si->txdma);
err_tx_dma:
sa1100_free_dma(si->rxdma);
err_rx_dma:
free_irq(dev->irq, dev);
err_irq:
return err;
}
static int sa1100_irda_stop(struct net_device *dev)
{
struct sa1100_irda *si = netdev_priv(dev);
disable_irq(dev->irq);
sa1100_irda_shutdown(si);
/*
* If we have been doing DMA receive, make sure we
* tidy that up cleanly.
*/
if (si->rxskb) {
dma_unmap_single(si->dev, si->rxbuf_dma, HPSIR_MAX_RXLEN,
DMA_FROM_DEVICE);
dev_kfree_skb(si->rxskb);
si->rxskb = NULL;
}
/* Stop IrLAP */
if (si->irlap) {
irlap_close(si->irlap);
si->irlap = NULL;
}
netif_stop_queue(dev);
si->open = 0;
/*
* Free resources
*/
sa1100_free_dma(si->txdma);
sa1100_free_dma(si->rxdma);
free_irq(dev->irq, dev);
sa1100_set_power(si, 0);
return 0;
}
static int sa1100_irda_init_iobuf(iobuff_t *io, int size)
{
io->head = kmalloc(size, GFP_KERNEL | GFP_DMA);
if (io->head != NULL) {
io->truesize = size;
io->in_frame = FALSE;
io->state = OUTSIDE_FRAME;
io->data = io->head;
}
return io->head ? 0 : -ENOMEM;
}
static const struct net_device_ops sa1100_irda_netdev_ops = {
.ndo_open = sa1100_irda_start,
.ndo_stop = sa1100_irda_stop,
.ndo_start_xmit = sa1100_irda_hard_xmit,
.ndo_do_ioctl = sa1100_irda_ioctl,
};
static int sa1100_irda_probe(struct platform_device *pdev)
{
struct net_device *dev;
struct sa1100_irda *si;
unsigned int baudrate_mask;
int err;
if (!pdev->dev.platform_data)
return -EINVAL;
err = request_mem_region(__PREG(Ser2UTCR0), 0x24, "IrDA") ? 0 : -EBUSY;
if (err)
goto err_mem_1;
err = request_mem_region(__PREG(Ser2HSCR0), 0x1c, "IrDA") ? 0 : -EBUSY;
if (err)
goto err_mem_2;
err = request_mem_region(__PREG(Ser2HSCR2), 0x04, "IrDA") ? 0 : -EBUSY;
if (err)
goto err_mem_3;
dev = alloc_irdadev(sizeof(struct sa1100_irda));
if (!dev)
goto err_mem_4;
si = netdev_priv(dev);
si->dev = &pdev->dev;
si->pdata = pdev->dev.platform_data;
/*
* Initialise the HP-SIR buffers
*/
err = sa1100_irda_init_iobuf(&si->rx_buff, 14384);
if (err)
goto err_mem_5;
err = sa1100_irda_init_iobuf(&si->tx_buff, 4000);
if (err)
goto err_mem_5;
dev->netdev_ops = &sa1100_irda_netdev_ops;
dev->irq = IRQ_Ser2ICP;
irda_init_max_qos_capabilies(&si->qos);
/*
* We support original IRDA up to 115k2. (we don't currently
* support 4Mbps). Min Turn Time set to 1ms or greater.
*/
baudrate_mask = IR_9600;
switch (max_rate) {
case 4000000: baudrate_mask |= IR_4000000 << 8;
case 115200: baudrate_mask |= IR_115200;
case 57600: baudrate_mask |= IR_57600;
case 38400: baudrate_mask |= IR_38400;
case 19200: baudrate_mask |= IR_19200;
}
si->qos.baud_rate.bits &= baudrate_mask;
si->qos.min_turn_time.bits = 7;
irda_qos_bits_to_value(&si->qos);
si->utcr4 = UTCR4_HPSIR;
if (tx_lpm)
si->utcr4 |= UTCR4_Z1_6us;
/*
* Initially enable HP-SIR modulation, and ensure that the port
* is disabled.
*/
Ser2UTCR3 = 0;
Ser2UTCR4 = si->utcr4;
Ser2HSCR0 = HSCR0_UART;
err = register_netdev(dev);
if (err == 0)
platform_set_drvdata(pdev, dev);
if (err) {
err_mem_5:
kfree(si->tx_buff.head);
kfree(si->rx_buff.head);
free_netdev(dev);
err_mem_4:
release_mem_region(__PREG(Ser2HSCR2), 0x04);
err_mem_3:
release_mem_region(__PREG(Ser2HSCR0), 0x1c);
err_mem_2:
release_mem_region(__PREG(Ser2UTCR0), 0x24);
}
err_mem_1:
return err;
}
static int sa1100_irda_remove(struct platform_device *pdev)
{
struct net_device *dev = platform_get_drvdata(pdev);
if (dev) {
struct sa1100_irda *si = netdev_priv(dev);
unregister_netdev(dev);
kfree(si->tx_buff.head);
kfree(si->rx_buff.head);
free_netdev(dev);
}
release_mem_region(__PREG(Ser2HSCR2), 0x04);
release_mem_region(__PREG(Ser2HSCR0), 0x1c);
release_mem_region(__PREG(Ser2UTCR0), 0x24);
return 0;
}
static struct platform_driver sa1100ir_driver = {
.probe = sa1100_irda_probe,
.remove = sa1100_irda_remove,
.suspend = sa1100_irda_suspend,
.resume = sa1100_irda_resume,
.driver = {
.name = "sa11x0-ir",
.owner = THIS_MODULE,
},
};
static int __init sa1100_irda_init(void)
{
/*
* Limit power level a sensible range.
*/
if (power_level < 1)
power_level = 1;
if (power_level > 3)
power_level = 3;
return platform_driver_register(&sa1100ir_driver);
}
static void __exit sa1100_irda_exit(void)
{
platform_driver_unregister(&sa1100ir_driver);
}
module_init(sa1100_irda_init);
module_exit(sa1100_irda_exit);
module_param(power_level, int, 0);
module_param(tx_lpm, int, 0);
module_param(max_rate, int, 0);
MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
MODULE_DESCRIPTION("StrongARM SA1100 IrDA driver");
MODULE_LICENSE("GPL");
MODULE_PARM_DESC(power_level, "IrDA power level, 1 (low) to 3 (high)");
MODULE_PARM_DESC(tx_lpm, "Enable transmitter low power (1.6us) mode");
MODULE_PARM_DESC(max_rate, "Maximum baud rate (4000000, 115200, 57600, 38400, 19200, 9600)");
MODULE_ALIAS("platform:sa11x0-ir");