- 根目录:
- drivers
- mmc
- core
- mmc_ops.c
/*
* linux/drivers/mmc/core/mmc_ops.h
*
* Copyright 2006-2007 Pierre Ossman
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
#include <linux/slab.h>
#include <linux/export.h>
#include <linux/types.h>
#include <linux/scatterlist.h>
#include <linux/mmc/host.h>
#include <linux/mmc/card.h>
#include <linux/mmc/mmc.h>
#include "core.h"
#include "mmc_ops.h"
static int _mmc_select_card(struct mmc_host *host, struct mmc_card *card)
{
int err;
struct mmc_command cmd = {0};
BUG_ON(!host);
cmd.opcode = MMC_SELECT_CARD;
if (card) {
cmd.arg = card->rca << 16;
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
} else {
cmd.arg = 0;
cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
}
err = mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
return 0;
}
int mmc_select_card(struct mmc_card *card)
{
BUG_ON(!card);
return _mmc_select_card(card->host, card);
}
int mmc_deselect_cards(struct mmc_host *host)
{
return _mmc_select_card(host, NULL);
}
int mmc_card_sleepawake(struct mmc_host *host, int sleep)
{
struct mmc_command cmd = {0};
struct mmc_card *card = host->card;
int err;
if (sleep)
mmc_deselect_cards(host);
cmd.opcode = MMC_SLEEP_AWAKE;
cmd.arg = card->rca << 16;
if (sleep)
cmd.arg |= 1 << 15;
cmd.flags = MMC_RSP_R1B | MMC_CMD_AC;
err = mmc_wait_for_cmd(host, &cmd, 0);
if (err)
return err;
/*
* If the host does not wait while the card signals busy, then we will
* will have to wait the sleep/awake timeout. Note, we cannot use the
* SEND_STATUS command to poll the status because that command (and most
* others) is invalid while the card sleeps.
*/
if (!(host->caps & MMC_CAP_WAIT_WHILE_BUSY))
mmc_delay(DIV_ROUND_UP(card->ext_csd.sa_timeout, 10000));
if (!sleep)
err = mmc_select_card(card);
return err;
}
int mmc_go_idle(struct mmc_host *host)
{
int err;
struct mmc_command cmd = {0};
/*
* Non-SPI hosts need to prevent chipselect going active during
* GO_IDLE; that would put chips into SPI mode. Remind them of
* that in case of hardware that won't pull up DAT3/nCS otherwise.
*
* SPI hosts ignore ios.chip_select; it's managed according to
* rules that must accommodate non-MMC slaves which this layer
* won't even know about.
*/
if (!mmc_host_is_spi(host)) {
mmc_set_chip_select(host, MMC_CS_HIGH);
mmc_delay(1);
}
cmd.opcode = MMC_GO_IDLE_STATE;
cmd.arg = 0;
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_NONE | MMC_CMD_BC;
err = mmc_wait_for_cmd(host, &cmd, 0);
mmc_delay(1);
if (!mmc_host_is_spi(host)) {
mmc_set_chip_select(host, MMC_CS_DONTCARE);
mmc_delay(1);
}
host->use_spi_crc = 0;
return err;
}
int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
{
struct mmc_command cmd = {0};
int i, err = 0;
BUG_ON(!host);
cmd.opcode = MMC_SEND_OP_COND;
cmd.arg = mmc_host_is_spi(host) ? 0 : ocr;
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R3 | MMC_CMD_BCR;
for (i = 100; i; i--) {
err = mmc_wait_for_cmd(host, &cmd, 0);
if (err)
break;
/* if we're just probing, do a single pass */
if (ocr == 0)
break;
/* otherwise wait until reset completes */
if (mmc_host_is_spi(host)) {
if (!(cmd.resp[0] & R1_SPI_IDLE))
break;
} else {
if (cmd.resp[0] & MMC_CARD_BUSY)
break;
}
err = -ETIMEDOUT;
mmc_delay(10);
}
if (rocr && !mmc_host_is_spi(host))
*rocr = cmd.resp[0];
return err;
}
int mmc_all_send_cid(struct mmc_host *host, u32 *cid)
{
int err;
struct mmc_command cmd = {0};
BUG_ON(!host);
BUG_ON(!cid);
cmd.opcode = MMC_ALL_SEND_CID;
cmd.arg = 0;
cmd.flags = MMC_RSP_R2 | MMC_CMD_BCR;
err = mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
memcpy(cid, cmd.resp, sizeof(u32) * 4);
return 0;
}
int mmc_set_relative_addr(struct mmc_card *card)
{
int err;
struct mmc_command cmd = {0};
BUG_ON(!card);
BUG_ON(!card->host);
cmd.opcode = MMC_SET_RELATIVE_ADDR;
cmd.arg = card->rca << 16;
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
err = mmc_wait_for_cmd(card->host, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
return 0;
}
static int
mmc_send_cxd_native(struct mmc_host *host, u32 arg, u32 *cxd, int opcode)
{
int err;
struct mmc_command cmd = {0};
BUG_ON(!host);
BUG_ON(!cxd);
cmd.opcode = opcode;
cmd.arg = arg;
cmd.flags = MMC_RSP_R2 | MMC_CMD_AC;
err = mmc_wait_for_cmd(host, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
memcpy(cxd, cmd.resp, sizeof(u32) * 4);
return 0;
}
static int
mmc_send_cxd_data(struct mmc_card *card, struct mmc_host *host,
u32 opcode, void *buf, unsigned len)
{
struct mmc_request mrq = {NULL};
struct mmc_command cmd = {0};
struct mmc_data data = {0};
struct scatterlist sg;
void *data_buf;
/* dma onto stack is unsafe/nonportable, but callers to this
* routine normally provide temporary on-stack buffers ...
*/
data_buf = kmalloc(len, GFP_KERNEL);
if (data_buf == NULL)
return -ENOMEM;
mrq.cmd = &cmd;
mrq.data = &data;
cmd.opcode = opcode;
cmd.arg = 0;
/* NOTE HACK: the MMC_RSP_SPI_R1 is always correct here, but we
* rely on callers to never use this with "native" calls for reading
* CSD or CID. Native versions of those commands use the R2 type,
* not R1 plus a data block.
*/
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
data.blksz = len;
data.blocks = 1;
data.flags = MMC_DATA_READ;
data.sg = &sg;
data.sg_len = 1;
sg_init_one(&sg, data_buf, len);
if (opcode == MMC_SEND_CSD || opcode == MMC_SEND_CID) {
/*
* The spec states that CSR and CID accesses have a timeout
* of 64 clock cycles.
*/
data.timeout_ns = 0;
data.timeout_clks = 64;
} else
mmc_set_data_timeout(&data, card);
mmc_wait_for_req(host, &mrq);
memcpy(buf, data_buf, len);
kfree(data_buf);
if (cmd.error)
return cmd.error;
if (data.error)
return data.error;
return 0;
}
int mmc_send_csd(struct mmc_card *card, u32 *csd)
{
int ret, i;
if (!mmc_host_is_spi(card->host))
return mmc_send_cxd_native(card->host, card->rca << 16,
csd, MMC_SEND_CSD);
ret = mmc_send_cxd_data(card, card->host, MMC_SEND_CSD, csd, 16);
if (ret)
return ret;
for (i = 0;i < 4;i++)
csd[i] = be32_to_cpu(csd[i]);
return 0;
}
int mmc_send_cid(struct mmc_host *host, u32 *cid)
{
int ret, i;
if (!mmc_host_is_spi(host)) {
if (!host->card)
return -EINVAL;
return mmc_send_cxd_native(host, host->card->rca << 16,
cid, MMC_SEND_CID);
}
ret = mmc_send_cxd_data(NULL, host, MMC_SEND_CID, cid, 16);
if (ret)
return ret;
for (i = 0;i < 4;i++)
cid[i] = be32_to_cpu(cid[i]);
return 0;
}
int mmc_send_ext_csd(struct mmc_card *card, u8 *ext_csd)
{
return mmc_send_cxd_data(card, card->host, MMC_SEND_EXT_CSD,
ext_csd, 512);
}
int mmc_spi_read_ocr(struct mmc_host *host, int highcap, u32 *ocrp)
{
struct mmc_command cmd = {0};
int err;
cmd.opcode = MMC_SPI_READ_OCR;
cmd.arg = highcap ? (1 << 30) : 0;
cmd.flags = MMC_RSP_SPI_R3;
err = mmc_wait_for_cmd(host, &cmd, 0);
*ocrp = cmd.resp[1];
return err;
}
int mmc_spi_set_crc(struct mmc_host *host, int use_crc)
{
struct mmc_command cmd = {0};
int err;
cmd.opcode = MMC_SPI_CRC_ON_OFF;
cmd.flags = MMC_RSP_SPI_R1;
cmd.arg = use_crc;
err = mmc_wait_for_cmd(host, &cmd, 0);
if (!err)
host->use_spi_crc = use_crc;
return err;
}
/**
* mmc_switch - modify EXT_CSD register
* @card: the MMC card associated with the data transfer
* @set: cmd set values
* @index: EXT_CSD register index
* @value: value to program into EXT_CSD register
* @timeout_ms: timeout (ms) for operation performed by register write,
* timeout of zero implies maximum possible timeout
*
* Modifies the EXT_CSD register for selected card.
*/
int mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
unsigned int timeout_ms)
{
int err;
struct mmc_command cmd = {0};
u32 status;
BUG_ON(!card);
BUG_ON(!card->host);
cmd.opcode = MMC_SWITCH;
cmd.arg = (MMC_SWITCH_MODE_WRITE_BYTE << 24) |
(index << 16) |
(value << 8) |
set;
cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
cmd.cmd_timeout_ms = timeout_ms;
err = mmc_wait_for_cmd(card->host, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
/* Must check status to be sure of no errors */
do {
err = mmc_send_status(card, &status);
if (err)
return err;
if (card->host->caps & MMC_CAP_WAIT_WHILE_BUSY)
break;
if (mmc_host_is_spi(card->host))
break;
} while (R1_CURRENT_STATE(status) == R1_STATE_PRG);
if (mmc_host_is_spi(card->host)) {
if (status & R1_SPI_ILLEGAL_COMMAND)
return -EBADMSG;
} else {
if (status & 0xFDFFA000)
pr_warning("%s: unexpected status %#x after "
"switch", mmc_hostname(card->host), status);
if (status & R1_SWITCH_ERROR)
return -EBADMSG;
}
return 0;
}
EXPORT_SYMBOL_GPL(mmc_switch);
int mmc_send_status(struct mmc_card *card, u32 *status)
{
int err;
struct mmc_command cmd = {0};
BUG_ON(!card);
BUG_ON(!card->host);
cmd.opcode = MMC_SEND_STATUS;
if (!mmc_host_is_spi(card->host))
cmd.arg = card->rca << 16;
cmd.flags = MMC_RSP_SPI_R2 | MMC_RSP_R1 | MMC_CMD_AC;
err = mmc_wait_for_cmd(card->host, &cmd, MMC_CMD_RETRIES);
if (err)
return err;
/* NOTE: callers are required to understand the difference
* between "native" and SPI format status words!
*/
if (status)
*status = cmd.resp[0];
return 0;
}
static int
mmc_send_bus_test(struct mmc_card *card, struct mmc_host *host, u8 opcode,
u8 len)
{
struct mmc_request mrq = {NULL};
struct mmc_command cmd = {0};
struct mmc_data data = {0};
struct scatterlist sg;
u8 *data_buf;
u8 *test_buf;
int i, err;
static u8 testdata_8bit[8] = { 0x55, 0xaa, 0, 0, 0, 0, 0, 0 };
static u8 testdata_4bit[4] = { 0x5a, 0, 0, 0 };
/* dma onto stack is unsafe/nonportable, but callers to this
* routine normally provide temporary on-stack buffers ...
*/
data_buf = kmalloc(len, GFP_KERNEL);
if (!data_buf)
return -ENOMEM;
if (len == 8)
test_buf = testdata_8bit;
else if (len == 4)
test_buf = testdata_4bit;
else {
pr_err("%s: Invalid bus_width %d\n",
mmc_hostname(host), len);
kfree(data_buf);
return -EINVAL;
}
if (opcode == MMC_BUS_TEST_W)
memcpy(data_buf, test_buf, len);
mrq.cmd = &cmd;
mrq.data = &data;
cmd.opcode = opcode;
cmd.arg = 0;
/* NOTE HACK: the MMC_RSP_SPI_R1 is always correct here, but we
* rely on callers to never use this with "native" calls for reading
* CSD or CID. Native versions of those commands use the R2 type,
* not R1 plus a data block.
*/
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
data.blksz = len;
data.blocks = 1;
if (opcode == MMC_BUS_TEST_R)
data.flags = MMC_DATA_READ;
else
data.flags = MMC_DATA_WRITE;
data.sg = &sg;
data.sg_len = 1;
sg_init_one(&sg, data_buf, len);
mmc_wait_for_req(host, &mrq);
err = 0;
if (opcode == MMC_BUS_TEST_R) {
for (i = 0; i < len / 4; i++)
if ((test_buf[i] ^ data_buf[i]) != 0xff) {
err = -EIO;
break;
}
}
kfree(data_buf);
if (cmd.error)
return cmd.error;
if (data.error)
return data.error;
return err;
}
int mmc_bus_test(struct mmc_card *card, u8 bus_width)
{
int err, width;
if (bus_width == MMC_BUS_WIDTH_8)
width = 8;
else if (bus_width == MMC_BUS_WIDTH_4)
width = 4;
else if (bus_width == MMC_BUS_WIDTH_1)
return 0; /* no need for test */
else
return -EINVAL;
/*
* Ignore errors from BUS_TEST_W. BUS_TEST_R will fail if there
* is a problem. This improves chances that the test will work.
*/
mmc_send_bus_test(card, card->host, MMC_BUS_TEST_W, width);
err = mmc_send_bus_test(card, card->host, MMC_BUS_TEST_R, width);
return err;
}
int mmc_send_hpi_cmd(struct mmc_card *card, u32 *status)
{
struct mmc_command cmd = {0};
unsigned int opcode;
unsigned int flags;
int err;
opcode = card->ext_csd.hpi_cmd;
if (opcode == MMC_STOP_TRANSMISSION)
flags = MMC_RSP_R1 | MMC_CMD_AC;
else if (opcode == MMC_SEND_STATUS)
flags = MMC_RSP_R1 | MMC_CMD_AC;
cmd.opcode = opcode;
cmd.arg = card->rca << 16 | 1;
cmd.flags = flags;
cmd.cmd_timeout_ms = card->ext_csd.out_of_int_time;
err = mmc_wait_for_cmd(card->host, &cmd, 0);
if (err) {
pr_warn("%s: error %d interrupting operation. "
"HPI command response %#x\n", mmc_hostname(card->host),
err, cmd.resp[0]);
return err;
}
if (status)
*status = cmd.resp[0];
return 0;
}