- 根目录:
- drivers
- usb
- host
- ehci-hub.c
/*
* Copyright (C) 2001-2004 by David Brownell
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/* this file is part of ehci-hcd.c */
/*-------------------------------------------------------------------------*/
/*
* EHCI Root Hub ... the nonsharable stuff
*
* Registers don't need cpu_to_le32, that happens transparently
*/
/*-------------------------------------------------------------------------*/
#include <linux/usb/otg.h>
#define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)
#ifdef CONFIG_PM
static int ehci_hub_control(
struct usb_hcd *hcd,
u16 typeReq,
u16 wValue,
u16 wIndex,
char *buf,
u16 wLength
);
/* After a power loss, ports that were owned by the companion must be
* reset so that the companion can still own them.
*/
static void ehci_handover_companion_ports(struct ehci_hcd *ehci)
{
u32 __iomem *reg;
u32 status;
int port;
__le32 buf;
struct usb_hcd *hcd = ehci_to_hcd(ehci);
if (!ehci->owned_ports)
return;
/* Give the connections some time to appear */
msleep(20);
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (test_bit(port, &ehci->owned_ports)) {
reg = &ehci->regs->port_status[port];
status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
/* Port already owned by companion? */
if (status & PORT_OWNER)
clear_bit(port, &ehci->owned_ports);
else if (test_bit(port, &ehci->companion_ports))
ehci_writel(ehci, status & ~PORT_PE, reg);
else
ehci_hub_control(hcd, SetPortFeature,
USB_PORT_FEAT_RESET, port + 1,
NULL, 0);
}
}
if (!ehci->owned_ports)
return;
msleep(90); /* Wait for resets to complete */
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (test_bit(port, &ehci->owned_ports)) {
ehci_hub_control(hcd, GetPortStatus,
0, port + 1,
(char *) &buf, sizeof(buf));
/* The companion should now own the port,
* but if something went wrong the port must not
* remain enabled.
*/
reg = &ehci->regs->port_status[port];
status = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
if (status & PORT_OWNER)
ehci_writel(ehci, status | PORT_CSC, reg);
else {
ehci_dbg(ehci, "failed handover port %d: %x\n",
port + 1, status);
ehci_writel(ehci, status & ~PORT_PE, reg);
}
}
}
ehci->owned_ports = 0;
}
static int ehci_port_change(struct ehci_hcd *ehci)
{
int i = HCS_N_PORTS(ehci->hcs_params);
/* First check if the controller indicates a change event */
if (ehci_readl(ehci, &ehci->regs->status) & STS_PCD)
return 1;
/*
* Not all controllers appear to update this while going from D3 to D0,
* so check the individual port status registers as well
*/
while (i--)
if (ehci_readl(ehci, &ehci->regs->port_status[i]) & PORT_CSC)
return 1;
return 0;
}
static __maybe_unused void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci,
bool suspending, bool do_wakeup)
{
int port;
u32 temp;
unsigned long flags;
/* If remote wakeup is enabled for the root hub but disabled
* for the controller, we must adjust all the port wakeup flags
* when the controller is suspended or resumed. In all other
* cases they don't need to be changed.
*/
if (!ehci_to_hcd(ehci)->self.root_hub->do_remote_wakeup || do_wakeup)
return;
spin_lock_irqsave(&ehci->lock, flags);
/* clear phy low-power mode before changing wakeup flags */
if (ehci->has_hostpc) {
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *hostpc_reg;
hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+ HOSTPC0 + 4 * port);
temp = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp & ~HOSTPC_PHCD, hostpc_reg);
}
spin_unlock_irqrestore(&ehci->lock, flags);
msleep(5);
spin_lock_irqsave(&ehci->lock, flags);
}
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status[port];
u32 t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
u32 t2 = t1 & ~PORT_WAKE_BITS;
/* If we are suspending the controller, clear the flags.
* If we are resuming the controller, set the wakeup flags.
*/
if (!suspending) {
if (t1 & PORT_CONNECT)
t2 |= PORT_WKOC_E | PORT_WKDISC_E;
else
t2 |= PORT_WKOC_E | PORT_WKCONN_E;
}
ehci_vdbg(ehci, "port %d, %08x -> %08x\n",
port + 1, t1, t2);
ehci_writel(ehci, t2, reg);
}
/* enter phy low-power mode again */
if (ehci->has_hostpc) {
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *hostpc_reg;
hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+ HOSTPC0 + 4 * port);
temp = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp | HOSTPC_PHCD, hostpc_reg);
}
}
/* Does the root hub have a port wakeup pending? */
if (!suspending && ehci_port_change(ehci))
usb_hcd_resume_root_hub(ehci_to_hcd(ehci));
spin_unlock_irqrestore(&ehci->lock, flags);
}
static int ehci_bus_suspend (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int port;
int mask;
int changed;
ehci_dbg(ehci, "suspend root hub\n");
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
del_timer_sync(&ehci->watchdog);
del_timer_sync(&ehci->iaa_watchdog);
spin_lock_irq (&ehci->lock);
/* Once the controller is stopped, port resumes that are already
* in progress won't complete. Hence if remote wakeup is enabled
* for the root hub and any ports are in the middle of a resume or
* remote wakeup, we must fail the suspend.
*/
if (hcd->self.root_hub->do_remote_wakeup) {
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
if (ehci->reset_done[port] != 0) {
spin_unlock_irq(&ehci->lock);
ehci_dbg(ehci, "suspend failed because "
"port %d is resuming\n",
port + 1);
return -EBUSY;
}
}
}
/* stop schedules, clean any completed work */
if (ehci->rh_state == EHCI_RH_RUNNING)
ehci_quiesce (ehci);
ehci->command = ehci_readl(ehci, &ehci->regs->command);
ehci_work(ehci);
/* Unlike other USB host controller types, EHCI doesn't have
* any notion of "global" or bus-wide suspend. The driver has
* to manually suspend all the active unsuspended ports, and
* then manually resume them in the bus_resume() routine.
*/
ehci->bus_suspended = 0;
ehci->owned_ports = 0;
changed = 0;
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status [port];
u32 t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
u32 t2 = t1 & ~PORT_WAKE_BITS;
/* keep track of which ports we suspend */
if (t1 & PORT_OWNER)
set_bit(port, &ehci->owned_ports);
else if ((t1 & PORT_PE) && !(t1 & PORT_SUSPEND)) {
t2 |= PORT_SUSPEND;
set_bit(port, &ehci->bus_suspended);
}
/* enable remote wakeup on all ports, if told to do so */
if (hcd->self.root_hub->do_remote_wakeup) {
/* only enable appropriate wake bits, otherwise the
* hardware can not go phy low power mode. If a race
* condition happens here(connection change during bits
* set), the port change detection will finally fix it.
*/
if (t1 & PORT_CONNECT)
t2 |= PORT_WKOC_E | PORT_WKDISC_E;
else
t2 |= PORT_WKOC_E | PORT_WKCONN_E;
}
if (t1 != t2) {
ehci_vdbg (ehci, "port %d, %08x -> %08x\n",
port + 1, t1, t2);
ehci_writel(ehci, t2, reg);
changed = 1;
}
}
if (changed && ehci->has_hostpc) {
spin_unlock_irq(&ehci->lock);
msleep(5); /* 5 ms for HCD to enter low-power mode */
spin_lock_irq(&ehci->lock);
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *hostpc_reg;
u32 t3;
hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+ HOSTPC0 + 4 * port);
t3 = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, t3 | HOSTPC_PHCD, hostpc_reg);
t3 = ehci_readl(ehci, hostpc_reg);
ehci_dbg(ehci, "Port %d phy low-power mode %s\n",
port, (t3 & HOSTPC_PHCD) ?
"succeeded" : "failed");
}
}
/* Apparently some devices need a >= 1-uframe delay here */
if (ehci->bus_suspended)
udelay(150);
/* turn off now-idle HC */
ehci_halt (ehci);
ehci->rh_state = EHCI_RH_SUSPENDED;
if (ehci->reclaim)
end_unlink_async(ehci);
/* allow remote wakeup */
mask = INTR_MASK;
if (!hcd->self.root_hub->do_remote_wakeup)
mask &= ~STS_PCD;
ehci_writel(ehci, mask, &ehci->regs->intr_enable);
ehci_readl(ehci, &ehci->regs->intr_enable);
ehci->next_statechange = jiffies + msecs_to_jiffies(10);
spin_unlock_irq (&ehci->lock);
/* ehci_work() may have re-enabled the watchdog timer, which we do not
* want, and so we must delete any pending watchdog timer events.
*/
del_timer_sync(&ehci->watchdog);
return 0;
}
/* caller has locked the root hub, and should reset/reinit on error */
static int ehci_bus_resume (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp;
u32 power_okay;
int i;
unsigned long resume_needed = 0;
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
spin_lock_irq (&ehci->lock);
if (!HCD_HW_ACCESSIBLE(hcd)) {
spin_unlock_irq(&ehci->lock);
return -ESHUTDOWN;
}
if (unlikely(ehci->debug)) {
if (!dbgp_reset_prep())
ehci->debug = NULL;
else
dbgp_external_startup();
}
/* Ideally and we've got a real resume here, and no port's power
* was lost. (For PCI, that means Vaux was maintained.) But we
* could instead be restoring a swsusp snapshot -- so that BIOS was
* the last user of the controller, not reset/pm hardware keeping
* state we gave to it.
*/
power_okay = ehci_readl(ehci, &ehci->regs->intr_enable);
ehci_dbg(ehci, "resume root hub%s\n",
power_okay ? "" : " after power loss");
/* at least some APM implementations will try to deliver
* IRQs right away, so delay them until we're ready.
*/
ehci_writel(ehci, 0, &ehci->regs->intr_enable);
/* re-init operational registers */
ehci_writel(ehci, 0, &ehci->regs->segment);
ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
ehci_writel(ehci, (u32) ehci->async->qh_dma, &ehci->regs->async_next);
/* restore CMD_RUN, framelist size, and irq threshold */
ehci_writel(ehci, ehci->command, &ehci->regs->command);
ehci->rh_state = EHCI_RH_RUNNING;
/* Some controller/firmware combinations need a delay during which
* they set up the port statuses. See Bugzilla #8190. */
spin_unlock_irq(&ehci->lock);
msleep(8);
spin_lock_irq(&ehci->lock);
/* clear phy low-power mode before resume */
if (ehci->bus_suspended && ehci->has_hostpc) {
i = HCS_N_PORTS(ehci->hcs_params);
while (i--) {
if (test_bit(i, &ehci->bus_suspended)) {
u32 __iomem *hostpc_reg;
hostpc_reg = (u32 __iomem *)((u8 *) ehci->regs
+ HOSTPC0 + 4 * i);
temp = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp & ~HOSTPC_PHCD,
hostpc_reg);
}
}
spin_unlock_irq(&ehci->lock);
msleep(5);
spin_lock_irq(&ehci->lock);
}
/* manually resume the ports we suspended during bus_suspend() */
i = HCS_N_PORTS (ehci->hcs_params);
while (i--) {
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
if (test_bit(i, &ehci->bus_suspended) &&
(temp & PORT_SUSPEND)) {
temp |= PORT_RESUME;
set_bit(i, &resume_needed);
}
ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
}
/* msleep for 20ms only if code is trying to resume port */
if (resume_needed) {
spin_unlock_irq(&ehci->lock);
msleep(20);
spin_lock_irq(&ehci->lock);
}
i = HCS_N_PORTS (ehci->hcs_params);
while (i--) {
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
if (test_bit(i, &resume_needed)) {
temp &= ~(PORT_RWC_BITS | PORT_RESUME);
ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
ehci_vdbg (ehci, "resumed port %d\n", i + 1);
}
}
(void) ehci_readl(ehci, &ehci->regs->command);
/* maybe re-activate the schedule(s) */
temp = 0;
if (ehci->async->qh_next.qh)
temp |= CMD_ASE;
if (ehci->periodic_sched)
temp |= CMD_PSE;
if (temp) {
ehci->command |= temp;
ehci_writel(ehci, ehci->command, &ehci->regs->command);
}
ehci->next_statechange = jiffies + msecs_to_jiffies(5);
/* Now we can safely re-enable irqs */
ehci_writel(ehci, INTR_MASK, &ehci->regs->intr_enable);
spin_unlock_irq (&ehci->lock);
ehci_handover_companion_ports(ehci);
return 0;
}
#else
#define ehci_bus_suspend NULL
#define ehci_bus_resume NULL
#endif /* CONFIG_PM */
/*-------------------------------------------------------------------------*/
/*
* Sets the owner of a port
*/
static void set_owner(struct ehci_hcd *ehci, int portnum, int new_owner)
{
u32 __iomem *status_reg;
u32 port_status;
int try;
status_reg = &ehci->regs->port_status[portnum];
/*
* The controller won't set the OWNER bit if the port is
* enabled, so this loop will sometimes require at least two
* iterations: one to disable the port and one to set OWNER.
*/
for (try = 4; try > 0; --try) {
spin_lock_irq(&ehci->lock);
port_status = ehci_readl(ehci, status_reg);
if ((port_status & PORT_OWNER) == new_owner
|| (port_status & (PORT_OWNER | PORT_CONNECT))
== 0)
try = 0;
else {
port_status ^= PORT_OWNER;
port_status &= ~(PORT_PE | PORT_RWC_BITS);
ehci_writel(ehci, port_status, status_reg);
}
spin_unlock_irq(&ehci->lock);
if (try > 1)
msleep(5);
}
}
/*-------------------------------------------------------------------------*/
static int check_reset_complete (
struct ehci_hcd *ehci,
int index,
u32 __iomem *status_reg,
int port_status
) {
if (!(port_status & PORT_CONNECT))
return port_status;
/* if reset finished and it's still not enabled -- handoff */
if (!(port_status & PORT_PE)) {
/* with integrated TT, there's nobody to hand it to! */
if (ehci_is_TDI(ehci)) {
ehci_dbg (ehci,
"Failed to enable port %d on root hub TT\n",
index+1);
return port_status;
}
ehci_dbg (ehci, "port %d full speed --> companion\n",
index + 1);
// what happens if HCS_N_CC(params) == 0 ?
port_status |= PORT_OWNER;
port_status &= ~PORT_RWC_BITS;
ehci_writel(ehci, port_status, status_reg);
/* ensure 440EPX ohci controller state is operational */
if (ehci->has_amcc_usb23)
set_ohci_hcfs(ehci, 1);
} else {
ehci_dbg (ehci, "port %d high speed\n", index + 1);
/* ensure 440EPx ohci controller state is suspended */
if (ehci->has_amcc_usb23)
set_ohci_hcfs(ehci, 0);
}
return port_status;
}
/*-------------------------------------------------------------------------*/
/* build "status change" packet (one or two bytes) from HC registers */
static int
ehci_hub_status_data (struct usb_hcd *hcd, char *buf)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
u32 temp, status = 0;
u32 mask;
int ports, i, retval = 1;
unsigned long flags;
u32 ppcd = 0;
/* if !USB_SUSPEND, root hub timers won't get shut down ... */
if (ehci->rh_state != EHCI_RH_RUNNING)
return 0;
/* init status to no-changes */
buf [0] = 0;
ports = HCS_N_PORTS (ehci->hcs_params);
if (ports > 7) {
buf [1] = 0;
retval++;
}
/* Some boards (mostly VIA?) report bogus overcurrent indications,
* causing massive log spam unless we completely ignore them. It
* may be relevant that VIA VT8235 controllers, where PORT_POWER is
* always set, seem to clear PORT_OCC and PORT_CSC when writing to
* PORT_POWER; that's surprising, but maybe within-spec.
*/
if (!ignore_oc)
mask = PORT_CSC | PORT_PEC | PORT_OCC;
else
mask = PORT_CSC | PORT_PEC;
// PORT_RESUME from hardware ~= PORT_STAT_C_SUSPEND
/* no hub change reports (bit 0) for now (power, ...) */
/* port N changes (bit N)? */
spin_lock_irqsave (&ehci->lock, flags);
/* get per-port change detect bits */
if (ehci->has_ppcd)
ppcd = ehci_readl(ehci, &ehci->regs->status) >> 16;
for (i = 0; i < ports; i++) {
/* leverage per-port change bits feature */
if (ehci->has_ppcd && !(ppcd & (1 << i)))
continue;
temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
/*
* Return status information even for ports with OWNER set.
* Otherwise khubd wouldn't see the disconnect event when a
* high-speed device is switched over to the companion
* controller by the user.
*/
if ((temp & mask) != 0 || test_bit(i, &ehci->port_c_suspend)
|| (ehci->reset_done[i] && time_after_eq(
jiffies, ehci->reset_done[i]))) {
if (i < 7)
buf [0] |= 1 << (i + 1);
else
buf [1] |= 1 << (i - 7);
status = STS_PCD;
}
}
/* FIXME autosuspend idle root hubs */
spin_unlock_irqrestore (&ehci->lock, flags);
return status ? retval : 0;
}
/*-------------------------------------------------------------------------*/
static void
ehci_hub_descriptor (
struct ehci_hcd *ehci,
struct usb_hub_descriptor *desc
) {
int ports = HCS_N_PORTS (ehci->hcs_params);
u16 temp;
desc->bDescriptorType = 0x29;
desc->bPwrOn2PwrGood = 10; /* ehci 1.0, 2.3.9 says 20ms max */
desc->bHubContrCurrent = 0;
desc->bNbrPorts = ports;
temp = 1 + (ports / 8);
desc->bDescLength = 7 + 2 * temp;
/* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */
memset(&desc->u.hs.DeviceRemovable[0], 0, temp);
memset(&desc->u.hs.DeviceRemovable[temp], 0xff, temp);
temp = 0x0008; /* per-port overcurrent reporting */
if (HCS_PPC (ehci->hcs_params))
temp |= 0x0001; /* per-port power control */
else
temp |= 0x0002; /* no power switching */
#if 0
// re-enable when we support USB_PORT_FEAT_INDICATOR below.
if (HCS_INDICATOR (ehci->hcs_params))
temp |= 0x0080; /* per-port indicators (LEDs) */
#endif
desc->wHubCharacteristics = cpu_to_le16(temp);
}
/*-------------------------------------------------------------------------*/
static int ehci_hub_control (
struct usb_hcd *hcd,
u16 typeReq,
u16 wValue,
u16 wIndex,
char *buf,
u16 wLength
) {
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int ports = HCS_N_PORTS (ehci->hcs_params);
u32 __iomem *status_reg = &ehci->regs->port_status[
(wIndex & 0xff) - 1];
u32 __iomem *hostpc_reg = NULL;
u32 temp, temp1, status;
unsigned long flags;
int retval = 0;
unsigned selector;
/*
* FIXME: support SetPortFeatures USB_PORT_FEAT_INDICATOR.
* HCS_INDICATOR may say we can change LEDs to off/amber/green.
* (track current state ourselves) ... blink for diagnostics,
* power, "this is the one", etc. EHCI spec supports this.
*/
if (ehci->has_hostpc)
hostpc_reg = (u32 __iomem *)((u8 *)ehci->regs
+ HOSTPC0 + 4 * ((wIndex & 0xff) - 1));
spin_lock_irqsave (&ehci->lock, flags);
switch (typeReq) {
case ClearHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case ClearPortFeature:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = ehci_readl(ehci, status_reg);
/*
* Even if OWNER is set, so the port is owned by the
* companion controller, khubd needs to be able to clear
* the port-change status bits (especially
* USB_PORT_STAT_C_CONNECTION).
*/
switch (wValue) {
case USB_PORT_FEAT_ENABLE:
ehci_writel(ehci, temp & ~PORT_PE, status_reg);
break;
case USB_PORT_FEAT_C_ENABLE:
ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_PEC,
status_reg);
break;
case USB_PORT_FEAT_SUSPEND:
if (temp & PORT_RESET)
goto error;
if (ehci->no_selective_suspend)
break;
#ifdef CONFIG_USB_OTG
if ((hcd->self.otg_port == (wIndex + 1))
&& hcd->self.b_hnp_enable) {
otg_start_hnp(ehci->transceiver);
break;
}
#endif
if (!(temp & PORT_SUSPEND))
break;
if ((temp & PORT_PE) == 0)
goto error;
/* clear phy low-power mode before resume */
if (hostpc_reg) {
temp1 = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp1 & ~HOSTPC_PHCD,
hostpc_reg);
spin_unlock_irqrestore(&ehci->lock, flags);
msleep(5);/* wait to leave low-power mode */
spin_lock_irqsave(&ehci->lock, flags);
}
/* resume signaling for 20 msec */
temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
ehci_writel(ehci, temp | PORT_RESUME, status_reg);
ehci->reset_done[wIndex] = jiffies
+ msecs_to_jiffies(20);
break;
case USB_PORT_FEAT_C_SUSPEND:
clear_bit(wIndex, &ehci->port_c_suspend);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC (ehci->hcs_params))
ehci_writel(ehci,
temp & ~(PORT_RWC_BITS | PORT_POWER),
status_reg);
break;
case USB_PORT_FEAT_C_CONNECTION:
if (ehci->has_lpm) {
/* clear PORTSC bits on disconnect */
temp &= ~PORT_LPM;
temp &= ~PORT_DEV_ADDR;
}
ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_CSC,
status_reg);
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_OCC,
status_reg);
break;
case USB_PORT_FEAT_C_RESET:
/* GetPortStatus clears reset */
break;
default:
goto error;
}
ehci_readl(ehci, &ehci->regs->command); /* unblock posted write */
break;
case GetHubDescriptor:
ehci_hub_descriptor (ehci, (struct usb_hub_descriptor *)
buf);
break;
case GetHubStatus:
/* no hub-wide feature/status flags */
memset (buf, 0, 4);
//cpu_to_le32s ((u32 *) buf);
break;
case GetPortStatus:
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
status = 0;
temp = ehci_readl(ehci, status_reg);
// wPortChange bits
if (temp & PORT_CSC)
status |= USB_PORT_STAT_C_CONNECTION << 16;
if (temp & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
if ((temp & PORT_OCC) && !ignore_oc){
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
/*
* Hubs should disable port power on over-current.
* However, not all EHCI implementations do this
* automatically, even if they _do_ support per-port
* power switching; they're allowed to just limit the
* current. khubd will turn the power back on.
*/
if ((temp & PORT_OC) && HCS_PPC(ehci->hcs_params)) {
ehci_writel(ehci,
temp & ~(PORT_RWC_BITS | PORT_POWER),
status_reg);
temp = ehci_readl(ehci, status_reg);
}
}
/* whoever resumes must GetPortStatus to complete it!! */
if (temp & PORT_RESUME) {
/* Remote Wakeup received? */
if (!ehci->reset_done[wIndex]) {
/* resume signaling for 20 msec */
ehci->reset_done[wIndex] = jiffies
+ msecs_to_jiffies(20);
/* check the port again */
mod_timer(&ehci_to_hcd(ehci)->rh_timer,
ehci->reset_done[wIndex]);
}
/* resume completed? */
else if (time_after_eq(jiffies,
ehci->reset_done[wIndex])) {
clear_bit(wIndex, &ehci->suspended_ports);
set_bit(wIndex, &ehci->port_c_suspend);
ehci->reset_done[wIndex] = 0;
/* stop resume signaling */
temp = ehci_readl(ehci, status_reg);
ehci_writel(ehci,
temp & ~(PORT_RWC_BITS | PORT_RESUME),
status_reg);
retval = handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
if (retval != 0) {
ehci_err(ehci,
"port %d resume error %d\n",
wIndex + 1, retval);
goto error;
}
temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10));
}
}
/* whoever resets must GetPortStatus to complete it!! */
if ((temp & PORT_RESET)
&& time_after_eq(jiffies,
ehci->reset_done[wIndex])) {
status |= USB_PORT_STAT_C_RESET << 16;
ehci->reset_done [wIndex] = 0;
/* force reset to complete */
ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESET),
status_reg);
/* REVISIT: some hardware needs 550+ usec to clear
* this bit; seems too long to spin routinely...
*/
retval = handshake(ehci, status_reg,
PORT_RESET, 0, 1000);
if (retval != 0) {
ehci_err (ehci, "port %d reset error %d\n",
wIndex + 1, retval);
goto error;
}
/* see what we found out */
temp = check_reset_complete (ehci, wIndex, status_reg,
ehci_readl(ehci, status_reg));
}
if (!(temp & (PORT_RESUME|PORT_RESET)))
ehci->reset_done[wIndex] = 0;
/* transfer dedicated ports to the companion hc */
if ((temp & PORT_CONNECT) &&
test_bit(wIndex, &ehci->companion_ports)) {
temp &= ~PORT_RWC_BITS;
temp |= PORT_OWNER;
ehci_writel(ehci, temp, status_reg);
ehci_dbg(ehci, "port %d --> companion\n", wIndex + 1);
temp = ehci_readl(ehci, status_reg);
}
/*
* Even if OWNER is set, there's no harm letting khubd
* see the wPortStatus values (they should all be 0 except
* for PORT_POWER anyway).
*/
if (temp & PORT_CONNECT) {
status |= USB_PORT_STAT_CONNECTION;
// status may be from integrated TT
if (ehci->has_hostpc) {
temp1 = ehci_readl(ehci, hostpc_reg);
status |= ehci_port_speed(ehci, temp1);
} else
status |= ehci_port_speed(ehci, temp);
}
if (temp & PORT_PE)
status |= USB_PORT_STAT_ENABLE;
/* maybe the port was unsuspended without our knowledge */
if (temp & (PORT_SUSPEND|PORT_RESUME)) {
status |= USB_PORT_STAT_SUSPEND;
} else if (test_bit(wIndex, &ehci->suspended_ports)) {
clear_bit(wIndex, &ehci->suspended_ports);
ehci->reset_done[wIndex] = 0;
if (temp & PORT_PE)
set_bit(wIndex, &ehci->port_c_suspend);
}
if (temp & PORT_OC)
status |= USB_PORT_STAT_OVERCURRENT;
if (temp & PORT_RESET)
status |= USB_PORT_STAT_RESET;
if (temp & PORT_POWER)
status |= USB_PORT_STAT_POWER;
if (test_bit(wIndex, &ehci->port_c_suspend))
status |= USB_PORT_STAT_C_SUSPEND << 16;
#ifndef VERBOSE_DEBUG
if (status & ~0xffff) /* only if wPortChange is interesting */
#endif
dbg_port (ehci, "GetStatus", wIndex + 1, temp);
put_unaligned_le32(status, buf);
break;
case SetHubFeature:
switch (wValue) {
case C_HUB_LOCAL_POWER:
case C_HUB_OVER_CURRENT:
/* no hub-wide feature/status flags */
break;
default:
goto error;
}
break;
case SetPortFeature:
selector = wIndex >> 8;
wIndex &= 0xff;
if (unlikely(ehci->debug)) {
/* If the debug port is active any port
* feature requests should get denied */
if (wIndex == HCS_DEBUG_PORT(ehci->hcs_params) &&
(readl(&ehci->debug->control) & DBGP_ENABLED)) {
retval = -ENODEV;
goto error_exit;
}
}
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
temp = ehci_readl(ehci, status_reg);
if (temp & PORT_OWNER)
break;
temp &= ~PORT_RWC_BITS;
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
if (ehci->no_selective_suspend)
break;
if ((temp & PORT_PE) == 0
|| (temp & PORT_RESET) != 0)
goto error;
/* After above check the port must be connected.
* Set appropriate bit thus could put phy into low power
* mode if we have hostpc feature
*/
temp &= ~PORT_WKCONN_E;
temp |= PORT_WKDISC_E | PORT_WKOC_E;
ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
if (hostpc_reg) {
spin_unlock_irqrestore(&ehci->lock, flags);
msleep(5);/* 5ms for HCD enter low pwr mode */
spin_lock_irqsave(&ehci->lock, flags);
temp1 = ehci_readl(ehci, hostpc_reg);
ehci_writel(ehci, temp1 | HOSTPC_PHCD,
hostpc_reg);
temp1 = ehci_readl(ehci, hostpc_reg);
ehci_dbg(ehci, "Port%d phy low pwr mode %s\n",
wIndex, (temp1 & HOSTPC_PHCD) ?
"succeeded" : "failed");
}
set_bit(wIndex, &ehci->suspended_ports);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC (ehci->hcs_params))
ehci_writel(ehci, temp | PORT_POWER,
status_reg);
break;
case USB_PORT_FEAT_RESET:
if (temp & PORT_RESUME)
goto error;
/* line status bits may report this as low speed,
* which can be fine if this root hub has a
* transaction translator built in.
*/
if ((temp & (PORT_PE|PORT_CONNECT)) == PORT_CONNECT
&& !ehci_is_TDI(ehci)
&& PORT_USB11 (temp)) {
ehci_dbg (ehci,
"port %d low speed --> companion\n",
wIndex + 1);
temp |= PORT_OWNER;
} else {
ehci_vdbg (ehci, "port %d reset\n", wIndex + 1);
temp |= PORT_RESET;
temp &= ~PORT_PE;
/*
* caller must wait, then call GetPortStatus
* usb 2.0 spec says 50 ms resets on root
*/
ehci->reset_done [wIndex] = jiffies
+ msecs_to_jiffies (50);
}
ehci_writel(ehci, temp, status_reg);
break;
/* For downstream facing ports (these): one hub port is put
* into test mode according to USB2 11.24.2.13, then the hub
* must be reset (which for root hub now means rmmod+modprobe,
* or else system reboot). See EHCI 2.3.9 and 4.14 for info
* about the EHCI-specific stuff.
*/
case USB_PORT_FEAT_TEST:
if (!selector || selector > 5)
goto error;
ehci_quiesce(ehci);
/* Put all enabled ports into suspend */
while (ports--) {
u32 __iomem *sreg =
&ehci->regs->port_status[ports];
temp = ehci_readl(ehci, sreg) & ~PORT_RWC_BITS;
if (temp & PORT_PE)
ehci_writel(ehci, temp | PORT_SUSPEND,
sreg);
}
ehci_halt(ehci);
temp = ehci_readl(ehci, status_reg);
temp |= selector << 16;
ehci_writel(ehci, temp, status_reg);
break;
default:
goto error;
}
ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
break;
default:
error:
/* "stall" on error */
retval = -EPIPE;
}
error_exit:
spin_unlock_irqrestore (&ehci->lock, flags);
return retval;
}
static void ehci_relinquish_port(struct usb_hcd *hcd, int portnum)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
if (ehci_is_TDI(ehci))
return;
set_owner(ehci, --portnum, PORT_OWNER);
}
static int ehci_port_handed_over(struct usb_hcd *hcd, int portnum)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
u32 __iomem *reg;
if (ehci_is_TDI(ehci))
return 0;
reg = &ehci->regs->port_status[portnum - 1];
return ehci_readl(ehci, reg) & PORT_OWNER;
}