- 根目录:
- sound
- pci
- ice1712
- juli.c
/*
* ALSA driver for ICEnsemble VT1724 (Envy24HT)
*
* Lowlevel functions for ESI Juli@ cards
*
* Copyright (c) 2004 Jaroslav Kysela <perex@perex.cz>
* 2008 Pavel Hofman <dustin@seznam.cz>
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <asm/io.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <sound/core.h>
#include <sound/tlv.h>
#include "ice1712.h"
#include "envy24ht.h"
#include "juli.h"
struct juli_spec {
struct ak4114 *ak4114;
unsigned int analog:1;
};
/*
* chip addresses on I2C bus
*/
#define AK4114_ADDR 0x20 /* S/PDIF receiver */
#define AK4358_ADDR 0x22 /* DAC */
/*
* Juli does not use the standard ICE1724 clock scheme. Juli's ice1724 chip is
* supplied by external clock provided by Xilinx array and MK73-1 PLL frequency
* multiplier. Actual frequency is set by ice1724 GPIOs hooked to the Xilinx.
*
* The clock circuitry is supplied by the two ice1724 crystals. This
* arrangement allows to generate independent clock signal for AK4114's input
* rate detection circuit. As a result, Juli, unlike most other
* ice1724+ak4114-based cards, detects spdif input rate correctly.
* This fact is applied in the driver, allowing to modify PCM stream rate
* parameter according to the actual input rate.
*
* Juli uses the remaining three stereo-channels of its DAC to optionally
* monitor analog input, digital input, and digital output. The corresponding
* I2S signals are routed by Xilinx, controlled by GPIOs.
*
* The master mute is implemented using output muting transistors (GPIO) in
* combination with smuting the DAC.
*
* The card itself has no HW master volume control, implemented using the
* vmaster control.
*
* TODO:
* researching and fixing the input monitors
*/
/*
* GPIO pins
*/
#define GPIO_FREQ_MASK (3<<0)
#define GPIO_FREQ_32KHZ (0<<0)
#define GPIO_FREQ_44KHZ (1<<0)
#define GPIO_FREQ_48KHZ (2<<0)
#define GPIO_MULTI_MASK (3<<2)
#define GPIO_MULTI_4X (0<<2)
#define GPIO_MULTI_2X (1<<2)
#define GPIO_MULTI_1X (2<<2) /* also external */
#define GPIO_MULTI_HALF (3<<2)
#define GPIO_INTERNAL_CLOCK (1<<4) /* 0 = external, 1 = internal */
#define GPIO_CLOCK_MASK (1<<4)
#define GPIO_ANALOG_PRESENT (1<<5) /* RO only: 0 = present */
#define GPIO_RXMCLK_SEL (1<<7) /* must be 0 */
#define GPIO_AK5385A_CKS0 (1<<8)
#define GPIO_AK5385A_DFS1 (1<<9)
#define GPIO_AK5385A_DFS0 (1<<10)
#define GPIO_DIGOUT_MONITOR (1<<11) /* 1 = active */
#define GPIO_DIGIN_MONITOR (1<<12) /* 1 = active */
#define GPIO_ANAIN_MONITOR (1<<13) /* 1 = active */
#define GPIO_AK5385A_CKS1 (1<<14) /* must be 0 */
#define GPIO_MUTE_CONTROL (1<<15) /* output mute, 1 = muted */
#define GPIO_RATE_MASK (GPIO_FREQ_MASK | GPIO_MULTI_MASK | \
GPIO_CLOCK_MASK)
#define GPIO_AK5385A_MASK (GPIO_AK5385A_CKS0 | GPIO_AK5385A_DFS0 | \
GPIO_AK5385A_DFS1 | GPIO_AK5385A_CKS1)
#define JULI_PCM_RATE (SNDRV_PCM_RATE_16000 | SNDRV_PCM_RATE_22050 | \
SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_64000 | \
SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 | \
SNDRV_PCM_RATE_176400 | SNDRV_PCM_RATE_192000)
#define GPIO_RATE_16000 (GPIO_FREQ_32KHZ | GPIO_MULTI_HALF | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_22050 (GPIO_FREQ_44KHZ | GPIO_MULTI_HALF | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_24000 (GPIO_FREQ_48KHZ | GPIO_MULTI_HALF | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_32000 (GPIO_FREQ_32KHZ | GPIO_MULTI_1X | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_44100 (GPIO_FREQ_44KHZ | GPIO_MULTI_1X | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_48000 (GPIO_FREQ_48KHZ | GPIO_MULTI_1X | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_64000 (GPIO_FREQ_32KHZ | GPIO_MULTI_2X | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_88200 (GPIO_FREQ_44KHZ | GPIO_MULTI_2X | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_96000 (GPIO_FREQ_48KHZ | GPIO_MULTI_2X | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_176400 (GPIO_FREQ_44KHZ | GPIO_MULTI_4X | \
GPIO_INTERNAL_CLOCK)
#define GPIO_RATE_192000 (GPIO_FREQ_48KHZ | GPIO_MULTI_4X | \
GPIO_INTERNAL_CLOCK)
/*
* Initial setup of the conversion array GPIO <-> rate
*/
static unsigned int juli_rates[] = {
16000, 22050, 24000, 32000,
44100, 48000, 64000, 88200,
96000, 176400, 192000,
};
static unsigned int gpio_vals[] = {
GPIO_RATE_16000, GPIO_RATE_22050, GPIO_RATE_24000, GPIO_RATE_32000,
GPIO_RATE_44100, GPIO_RATE_48000, GPIO_RATE_64000, GPIO_RATE_88200,
GPIO_RATE_96000, GPIO_RATE_176400, GPIO_RATE_192000,
};
static struct snd_pcm_hw_constraint_list juli_rates_info = {
.count = ARRAY_SIZE(juli_rates),
.list = juli_rates,
.mask = 0,
};
static int get_gpio_val(int rate)
{
int i;
for (i = 0; i < ARRAY_SIZE(juli_rates); i++)
if (juli_rates[i] == rate)
return gpio_vals[i];
return 0;
}
static void juli_ak4114_write(void *private_data, unsigned char reg,
unsigned char val)
{
snd_vt1724_write_i2c((struct snd_ice1712 *)private_data, AK4114_ADDR,
reg, val);
}
static unsigned char juli_ak4114_read(void *private_data, unsigned char reg)
{
return snd_vt1724_read_i2c((struct snd_ice1712 *)private_data,
AK4114_ADDR, reg);
}
/*
* If SPDIF capture and slaved to SPDIF-IN, setting runtime rate
* to the external rate
*/
static void juli_spdif_in_open(struct snd_ice1712 *ice,
struct snd_pcm_substream *substream)
{
struct juli_spec *spec = ice->spec;
struct snd_pcm_runtime *runtime = substream->runtime;
int rate;
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK ||
!ice->is_spdif_master(ice))
return;
rate = snd_ak4114_external_rate(spec->ak4114);
if (rate >= runtime->hw.rate_min && rate <= runtime->hw.rate_max) {
runtime->hw.rate_min = rate;
runtime->hw.rate_max = rate;
}
}
/*
* AK4358 section
*/
static void juli_akm_lock(struct snd_akm4xxx *ak, int chip)
{
}
static void juli_akm_unlock(struct snd_akm4xxx *ak, int chip)
{
}
static void juli_akm_write(struct snd_akm4xxx *ak, int chip,
unsigned char addr, unsigned char data)
{
struct snd_ice1712 *ice = ak->private_data[0];
if (snd_BUG_ON(chip))
return;
snd_vt1724_write_i2c(ice, AK4358_ADDR, addr, data);
}
/*
* change the rate of envy24HT, AK4358, AK5385
*/
static void juli_akm_set_rate_val(struct snd_akm4xxx *ak, unsigned int rate)
{
unsigned char old, tmp, ak4358_dfs;
unsigned int ak5385_pins, old_gpio, new_gpio;
struct snd_ice1712 *ice = ak->private_data[0];
struct juli_spec *spec = ice->spec;
if (rate == 0) /* no hint - S/PDIF input is master or the new spdif
input rate undetected, simply return */
return;
/* adjust DFS on codecs */
if (rate > 96000) {
ak4358_dfs = 2;
ak5385_pins = GPIO_AK5385A_DFS1 | GPIO_AK5385A_CKS0;
} else if (rate > 48000) {
ak4358_dfs = 1;
ak5385_pins = GPIO_AK5385A_DFS0;
} else {
ak4358_dfs = 0;
ak5385_pins = 0;
}
/* AK5385 first, since it requires cold reset affecting both codecs */
old_gpio = ice->gpio.get_data(ice);
new_gpio = (old_gpio & ~GPIO_AK5385A_MASK) | ak5385_pins;
/* printk(KERN_DEBUG "JULI - ak5385 set_rate_val: new gpio 0x%x\n",
new_gpio); */
ice->gpio.set_data(ice, new_gpio);
/* cold reset */
old = inb(ICEMT1724(ice, AC97_CMD));
outb(old | VT1724_AC97_COLD, ICEMT1724(ice, AC97_CMD));
udelay(1);
outb(old & ~VT1724_AC97_COLD, ICEMT1724(ice, AC97_CMD));
/* AK4358 */
/* set new value, reset DFS */
tmp = snd_akm4xxx_get(ak, 0, 2);
snd_akm4xxx_reset(ak, 1);
tmp = snd_akm4xxx_get(ak, 0, 2);
tmp &= ~(0x03 << 4);
tmp |= ak4358_dfs << 4;
snd_akm4xxx_set(ak, 0, 2, tmp);
snd_akm4xxx_reset(ak, 0);
/* reinit ak4114 */
snd_ak4114_reinit(spec->ak4114);
}
#define AK_DAC(xname, xch) { .name = xname, .num_channels = xch }
#define PCM_VOLUME "PCM Playback Volume"
#define MONITOR_AN_IN_VOLUME "Monitor Analog In Volume"
#define MONITOR_DIG_IN_VOLUME "Monitor Digital In Volume"
#define MONITOR_DIG_OUT_VOLUME "Monitor Digital Out Volume"
static const struct snd_akm4xxx_dac_channel juli_dac[] = {
AK_DAC(PCM_VOLUME, 2),
AK_DAC(MONITOR_AN_IN_VOLUME, 2),
AK_DAC(MONITOR_DIG_OUT_VOLUME, 2),
AK_DAC(MONITOR_DIG_IN_VOLUME, 2),
};
static struct snd_akm4xxx akm_juli_dac __devinitdata = {
.type = SND_AK4358,
.num_dacs = 8, /* DAC1 - analog out
DAC2 - analog in monitor
DAC3 - digital out monitor
DAC4 - digital in monitor
*/
.ops = {
.lock = juli_akm_lock,
.unlock = juli_akm_unlock,
.write = juli_akm_write,
.set_rate_val = juli_akm_set_rate_val
},
.dac_info = juli_dac,
};
#define juli_mute_info snd_ctl_boolean_mono_info
static int juli_mute_get(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_ice1712 *ice = snd_kcontrol_chip(kcontrol);
unsigned int val;
val = ice->gpio.get_data(ice) & (unsigned int) kcontrol->private_value;
if (kcontrol->private_value == GPIO_MUTE_CONTROL)
/* val 0 = signal on */
ucontrol->value.integer.value[0] = (val) ? 0 : 1;
else
/* val 1 = signal on */
ucontrol->value.integer.value[0] = (val) ? 1 : 0;
return 0;
}
static int juli_mute_put(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_ice1712 *ice = snd_kcontrol_chip(kcontrol);
unsigned int old_gpio, new_gpio;
old_gpio = ice->gpio.get_data(ice);
if (ucontrol->value.integer.value[0]) {
/* unmute */
if (kcontrol->private_value == GPIO_MUTE_CONTROL) {
/* 0 = signal on */
new_gpio = old_gpio & ~GPIO_MUTE_CONTROL;
/* un-smuting DAC */
snd_akm4xxx_write(ice->akm, 0, 0x01, 0x01);
} else
/* 1 = signal on */
new_gpio = old_gpio |
(unsigned int) kcontrol->private_value;
} else {
/* mute */
if (kcontrol->private_value == GPIO_MUTE_CONTROL) {
/* 1 = signal off */
new_gpio = old_gpio | GPIO_MUTE_CONTROL;
/* smuting DAC */
snd_akm4xxx_write(ice->akm, 0, 0x01, 0x03);
} else
/* 0 = signal off */
new_gpio = old_gpio &
~((unsigned int) kcontrol->private_value);
}
/* printk(KERN_DEBUG
"JULI - mute/unmute: control_value: 0x%x, old_gpio: 0x%x, "
"new_gpio 0x%x\n",
(unsigned int)ucontrol->value.integer.value[0], old_gpio,
new_gpio); */
if (old_gpio != new_gpio) {
ice->gpio.set_data(ice, new_gpio);
return 1;
}
/* no change */
return 0;
}
static struct snd_kcontrol_new juli_mute_controls[] __devinitdata = {
{
.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
.name = "Master Playback Switch",
.info = juli_mute_info,
.get = juli_mute_get,
.put = juli_mute_put,
.private_value = GPIO_MUTE_CONTROL,
},
/* Although the following functionality respects the succint NDA'd
* documentation from the card manufacturer, and the same way of
* operation is coded in OSS Juli driver, only Digital Out monitor
* seems to work. Surprisingly, Analog input monitor outputs Digital
* output data. The two are independent, as enabling both doubles
* volume of the monitor sound.
*
* Checking traces on the board suggests the functionality described
* by the manufacturer is correct - I2S from ADC and AK4114
* go to ICE as well as to Xilinx, I2S inputs of DAC2,3,4 (the monitor
* inputs) are fed from Xilinx.
*
* I even checked traces on board and coded a support in driver for
* an alternative possibility - the unused I2S ICE output channels
* switched to HW-IN/SPDIF-IN and providing the monitoring signal to
* the DAC - to no avail. The I2S outputs seem to be unconnected.
*
* The windows driver supports the monitoring correctly.
*/
{
.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
.name = "Monitor Analog In Switch",
.info = juli_mute_info,
.get = juli_mute_get,
.put = juli_mute_put,
.private_value = GPIO_ANAIN_MONITOR,
},
{
.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
.name = "Monitor Digital Out Switch",
.info = juli_mute_info,
.get = juli_mute_get,
.put = juli_mute_put,
.private_value = GPIO_DIGOUT_MONITOR,
},
{
.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
.name = "Monitor Digital In Switch",
.info = juli_mute_info,
.get = juli_mute_get,
.put = juli_mute_put,
.private_value = GPIO_DIGIN_MONITOR,
},
};
static char *slave_vols[] __devinitdata = {
PCM_VOLUME,
MONITOR_AN_IN_VOLUME,
MONITOR_DIG_IN_VOLUME,
MONITOR_DIG_OUT_VOLUME,
NULL
};
static __devinitdata
DECLARE_TLV_DB_SCALE(juli_master_db_scale, -6350, 50, 1);
static struct snd_kcontrol __devinit *ctl_find(struct snd_card *card,
const char *name)
{
struct snd_ctl_elem_id sid;
memset(&sid, 0, sizeof(sid));
/* FIXME: strcpy is bad. */
strcpy(sid.name, name);
sid.iface = SNDRV_CTL_ELEM_IFACE_MIXER;
return snd_ctl_find_id(card, &sid);
}
static void __devinit add_slaves(struct snd_card *card,
struct snd_kcontrol *master, char **list)
{
for (; *list; list++) {
struct snd_kcontrol *slave = ctl_find(card, *list);
/* printk(KERN_DEBUG "add_slaves - %s\n", *list); */
if (slave) {
/* printk(KERN_DEBUG "slave %s found\n", *list); */
snd_ctl_add_slave(master, slave);
}
}
}
static int __devinit juli_add_controls(struct snd_ice1712 *ice)
{
struct juli_spec *spec = ice->spec;
int err;
unsigned int i;
struct snd_kcontrol *vmaster;
err = snd_ice1712_akm4xxx_build_controls(ice);
if (err < 0)
return err;
for (i = 0; i < ARRAY_SIZE(juli_mute_controls); i++) {
err = snd_ctl_add(ice->card,
snd_ctl_new1(&juli_mute_controls[i], ice));
if (err < 0)
return err;
}
/* Create virtual master control */
vmaster = snd_ctl_make_virtual_master("Master Playback Volume",
juli_master_db_scale);
if (!vmaster)
return -ENOMEM;
add_slaves(ice->card, vmaster, slave_vols);
err = snd_ctl_add(ice->card, vmaster);
if (err < 0)
return err;
/* only capture SPDIF over AK4114 */
err = snd_ak4114_build(spec->ak4114, NULL,
ice->pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream);
if (err < 0)
return err;
return 0;
}
/*
* suspend/resume
* */
#ifdef CONFIG_PM
static int juli_resume(struct snd_ice1712 *ice)
{
struct snd_akm4xxx *ak = ice->akm;
struct juli_spec *spec = ice->spec;
/* akm4358 un-reset, un-mute */
snd_akm4xxx_reset(ak, 0);
/* reinit ak4114 */
snd_ak4114_reinit(spec->ak4114);
return 0;
}
static int juli_suspend(struct snd_ice1712 *ice)
{
struct snd_akm4xxx *ak = ice->akm;
/* akm4358 reset and soft-mute */
snd_akm4xxx_reset(ak, 1);
return 0;
}
#endif
/*
* initialize the chip
*/
static inline int juli_is_spdif_master(struct snd_ice1712 *ice)
{
return (ice->gpio.get_data(ice) & GPIO_INTERNAL_CLOCK) ? 0 : 1;
}
static unsigned int juli_get_rate(struct snd_ice1712 *ice)
{
int i;
unsigned char result;
result = ice->gpio.get_data(ice) & GPIO_RATE_MASK;
for (i = 0; i < ARRAY_SIZE(gpio_vals); i++)
if (gpio_vals[i] == result)
return juli_rates[i];
return 0;
}
/* setting new rate */
static void juli_set_rate(struct snd_ice1712 *ice, unsigned int rate)
{
unsigned int old, new;
unsigned char val;
old = ice->gpio.get_data(ice);
new = (old & ~GPIO_RATE_MASK) | get_gpio_val(rate);
/* printk(KERN_DEBUG "JULI - set_rate: old %x, new %x\n",
old & GPIO_RATE_MASK,
new & GPIO_RATE_MASK); */
ice->gpio.set_data(ice, new);
/* switching to external clock - supplied by external circuits */
val = inb(ICEMT1724(ice, RATE));
outb(val | VT1724_SPDIF_MASTER, ICEMT1724(ice, RATE));
}
static inline unsigned char juli_set_mclk(struct snd_ice1712 *ice,
unsigned int rate)
{
/* no change in master clock */
return 0;
}
/* setting clock to external - SPDIF */
static int juli_set_spdif_clock(struct snd_ice1712 *ice, int type)
{
unsigned int old;
old = ice->gpio.get_data(ice);
/* external clock (= 0), multiply 1x, 48kHz */
ice->gpio.set_data(ice, (old & ~GPIO_RATE_MASK) | GPIO_MULTI_1X |
GPIO_FREQ_48KHZ);
return 0;
}
/* Called when ak4114 detects change in the input SPDIF stream */
static void juli_ak4114_change(struct ak4114 *ak4114, unsigned char c0,
unsigned char c1)
{
struct snd_ice1712 *ice = ak4114->change_callback_private;
int rate;
if (ice->is_spdif_master(ice) && c1) {
/* only for SPDIF master mode, rate was changed */
rate = snd_ak4114_external_rate(ak4114);
/* printk(KERN_DEBUG "ak4114 - input rate changed to %d\n",
rate); */
juli_akm_set_rate_val(ice->akm, rate);
}
}
static int __devinit juli_init(struct snd_ice1712 *ice)
{
static const unsigned char ak4114_init_vals[] = {
/* AK4117_REG_PWRDN */ AK4114_RST | AK4114_PWN |
AK4114_OCKS0 | AK4114_OCKS1,
/* AK4114_REQ_FORMAT */ AK4114_DIF_I24I2S,
/* AK4114_REG_IO0 */ AK4114_TX1E,
/* AK4114_REG_IO1 */ AK4114_EFH_1024 | AK4114_DIT |
AK4114_IPS(1),
/* AK4114_REG_INT0_MASK */ 0,
/* AK4114_REG_INT1_MASK */ 0
};
static const unsigned char ak4114_init_txcsb[] = {
0x41, 0x02, 0x2c, 0x00, 0x00
};
int err;
struct juli_spec *spec;
struct snd_akm4xxx *ak;
spec = kzalloc(sizeof(*spec), GFP_KERNEL);
if (!spec)
return -ENOMEM;
ice->spec = spec;
err = snd_ak4114_create(ice->card,
juli_ak4114_read,
juli_ak4114_write,
ak4114_init_vals, ak4114_init_txcsb,
ice, &spec->ak4114);
if (err < 0)
return err;
/* callback for codecs rate setting */
spec->ak4114->change_callback = juli_ak4114_change;
spec->ak4114->change_callback_private = ice;
/* AK4114 in Juli can detect external rate correctly */
spec->ak4114->check_flags = 0;
#if 0
/*
* it seems that the analog doughter board detection does not work reliably, so
* force the analog flag; it should be very rare (if ever) to come at Juli@
* used without the analog daughter board
*/
spec->analog = (ice->gpio.get_data(ice) & GPIO_ANALOG_PRESENT) ? 0 : 1;
#else
spec->analog = 1;
#endif
if (spec->analog) {
printk(KERN_INFO "juli@: analog I/O detected\n");
ice->num_total_dacs = 2;
ice->num_total_adcs = 2;
ice->akm = kzalloc(sizeof(struct snd_akm4xxx), GFP_KERNEL);
ak = ice->akm;
if (!ak)
return -ENOMEM;
ice->akm_codecs = 1;
err = snd_ice1712_akm4xxx_init(ak, &akm_juli_dac, NULL, ice);
if (err < 0)
return err;
}
/* juli is clocked by Xilinx array */
ice->hw_rates = &juli_rates_info;
ice->is_spdif_master = juli_is_spdif_master;
ice->get_rate = juli_get_rate;
ice->set_rate = juli_set_rate;
ice->set_mclk = juli_set_mclk;
ice->set_spdif_clock = juli_set_spdif_clock;
ice->spdif.ops.open = juli_spdif_in_open;
#ifdef CONFIG_PM
ice->pm_resume = juli_resume;
ice->pm_suspend = juli_suspend;
ice->pm_suspend_enabled = 1;
#endif
return 0;
}
/*
* Juli@ boards don't provide the EEPROM data except for the vendor IDs.
* hence the driver needs to sets up it properly.
*/
static unsigned char juli_eeprom[] __devinitdata = {
[ICE_EEP2_SYSCONF] = 0x2b, /* clock 512, mpu401, 1xADC, 1xDACs,
SPDIF in */
[ICE_EEP2_ACLINK] = 0x80, /* I2S */
[ICE_EEP2_I2S] = 0xf8, /* vol, 96k, 24bit, 192k */
[ICE_EEP2_SPDIF] = 0xc3, /* out-en, out-int, spdif-in */
[ICE_EEP2_GPIO_DIR] = 0x9f, /* 5, 6:inputs; 7, 4-0 outputs*/
[ICE_EEP2_GPIO_DIR1] = 0xff,
[ICE_EEP2_GPIO_DIR2] = 0x7f,
[ICE_EEP2_GPIO_MASK] = 0x60, /* 5, 6: locked; 7, 4-0 writable */
[ICE_EEP2_GPIO_MASK1] = 0x00, /* 0-7 writable */
[ICE_EEP2_GPIO_MASK2] = 0x7f,
[ICE_EEP2_GPIO_STATE] = GPIO_FREQ_48KHZ | GPIO_MULTI_1X |
GPIO_INTERNAL_CLOCK, /* internal clock, multiple 1x, 48kHz*/
[ICE_EEP2_GPIO_STATE1] = 0x00, /* unmuted */
[ICE_EEP2_GPIO_STATE2] = 0x00,
};
/* entry point */
struct snd_ice1712_card_info snd_vt1724_juli_cards[] __devinitdata = {
{
.subvendor = VT1724_SUBDEVICE_JULI,
.name = "ESI Juli@",
.model = "juli",
.chip_init = juli_init,
.build_controls = juli_add_controls,
.eeprom_size = sizeof(juli_eeprom),
.eeprom_data = juli_eeprom,
},
{ } /* terminator */
};