/*
This is part of rtl8187 OpenSource driver.
Copyright (C) Andrea Merello 2004-2005 <andreamrl@tiscali.it>
Released under the terms of GPL (General Public Licence)
Parts of this driver are based on the GPL part of the
official Realtek driver.
Parts of this driver are based on the rtl8180 driver skeleton
from Patric Schenke & Andres Salomon.
Parts of this driver are based on the Intel Pro Wireless
2100 GPL driver.
We want to tanks the Authors of those projects
and the Ndiswrapper project Authors.
*/
/* Mariusz Matuszek added full registers definition with Realtek's name */
/* this file contains register definitions for the rtl8187 MAC controller */
#ifndef R8192_HW
#define R8192_HW
typedef enum _VERSION_819xU{
VERSION_819xU_A, // A-cut
VERSION_819xU_B, // B-cut
VERSION_819xU_C,// C-cut
}VERSION_819xU,*PVERSION_819xU;
//added for different RF type
typedef enum _RT_RF_TYPE_DEF
{
RF_1T2R = 0,
RF_2T4R,
RF_819X_MAX_TYPE
}RT_RF_TYPE_DEF;
typedef enum _BaseBand_Config_Type{
BaseBand_Config_PHY_REG = 0, //Radio Path A
BaseBand_Config_AGC_TAB = 1, //Radio Path B
}BaseBand_Config_Type, *PBaseBand_Config_Type;
#define RTL8187_REQT_READ 0xc0
#define RTL8187_REQT_WRITE 0x40
#define RTL8187_REQ_GET_REGS 0x05
#define RTL8187_REQ_SET_REGS 0x05
#define MAX_TX_URB 5
#define MAX_RX_URB 16
#define R8180_MAX_RETRY 255
//#define MAX_RX_NORMAL_URB 3
//#define MAX_RX_COMMAND_URB 2
#define RX_URB_SIZE 9100
#define BB_ANTATTEN_CHAN14 0x0c
#define BB_ANTENNA_B 0x40
#define BB_HOST_BANG (1<<30)
#define BB_HOST_BANG_EN (1<<2)
#define BB_HOST_BANG_CLK (1<<1)
#define BB_HOST_BANG_RW (1<<3)
#define BB_HOST_BANG_DATA 1
//#if (RTL819X_FPGA_VER & RTL819X_FPGA_VIVI_070920)
#define AFR 0x010
#define AFR_CardBEn (1<<0)
#define AFR_CLKRUN_SEL (1<<1)
#define AFR_FuncRegEn (1<<2)
#define RTL8190_EEPROM_ID 0x8129
#define EEPROM_VID 0x02
#define EEPROM_PID 0x04
#define EEPROM_NODE_ADDRESS_BYTE_0 0x0C
#define EEPROM_TxPowerDiff 0x1F
#define EEPROM_ThermalMeter 0x20
#define EEPROM_PwDiff 0x21 //0x21
#define EEPROM_CrystalCap 0x22 //0x22
#define EEPROM_TxPwIndex_CCK 0x23 //0x23
#define EEPROM_TxPwIndex_OFDM_24G 0x24 //0x24~0x26
#define EEPROM_TxPwIndex_CCK_V1 0x29 //0x29~0x2B
#define EEPROM_TxPwIndex_OFDM_24G_V1 0x2C //0x2C~0x2E
#define EEPROM_TxPwIndex_Ver 0x27 //0x27
#define EEPROM_Default_TxPowerDiff 0x0
#define EEPROM_Default_ThermalMeter 0x7
#define EEPROM_Default_PwDiff 0x4
#define EEPROM_Default_CrystalCap 0x5
#define EEPROM_Default_TxPower 0x1010
#define EEPROM_Customer_ID 0x7B //0x7B:CustomerID
#define EEPROM_ChannelPlan 0x16 //0x7C
#define EEPROM_IC_VER 0x7d //0x7D
#define EEPROM_CRC 0x7e //0x7E~0x7F
#define EEPROM_CID_DEFAULT 0x0
#define EEPROM_CID_CAMEO 0x1
#define EEPROM_CID_RUNTOP 0x2
#define EEPROM_CID_Senao 0x3
#define EEPROM_CID_TOSHIBA 0x4 // Toshiba setting, Merge by Jacken, 2008/01/31
#define EEPROM_CID_NetCore 0x5
#define EEPROM_CID_Nettronix 0x6
#define EEPROM_CID_Pronet 0x7
#define EEPROM_CID_DLINK 0x8
#define AC_PARAM_TXOP_LIMIT_OFFSET 16
#define AC_PARAM_ECW_MAX_OFFSET 12
#define AC_PARAM_ECW_MIN_OFFSET 8
#define AC_PARAM_AIFS_OFFSET 0
//#endif
enum _RTL8192Usb_HW {
PCIF = 0x009, // PCI Function Register 0x0009h~0x000bh
#define BB_GLOBAL_RESET_BIT 0x1
BB_GLOBAL_RESET = 0x020, // BasebandGlobal Reset Register
BSSIDR = 0x02E, // BSSID Register
CMDR = 0x037, // Command register
#define CR_RST 0x10
#define CR_RE 0x08
#define CR_TE 0x04
#define CR_MulRW 0x01
SIFS = 0x03E, // SIFS register
TCR = 0x040, // Transmit Configuration Register
#define TCR_MXDMA_2048 7
#define TCR_LRL_OFFSET 0
#define TCR_SRL_OFFSET 8
#define TCR_MXDMA_OFFSET 21
#define TCR_SAT BIT24 // Enable Rate depedent ack timeout timer
RCR = 0x044, // Receive Configuration Register
#define MAC_FILTER_MASK ((1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<5) | \
(1<<12) | (1<<18) | (1<<19) | (1<<20) | (1<<21) | (1<<22) | (1<<23))
#define RX_FIFO_THRESHOLD_MASK ((1<<13) | (1<<14) | (1<<15))
#define RX_FIFO_THRESHOLD_SHIFT 13
#define RX_FIFO_THRESHOLD_128 3
#define RX_FIFO_THRESHOLD_256 4
#define RX_FIFO_THRESHOLD_512 5
#define RX_FIFO_THRESHOLD_1024 6
#define RX_FIFO_THRESHOLD_NONE 7
#define MAX_RX_DMA_MASK ((1<<8) | (1<<9) | (1<<10))
#define RCR_MXDMA_OFFSET 8
#define RCR_FIFO_OFFSET 13
#define RCR_ONLYERLPKT BIT31 // Early Receiving based on Packet Size.
#define RCR_ENCS2 BIT30 // Enable Carrier Sense Detection Method 2
#define RCR_ENCS1 BIT29 // Enable Carrier Sense Detection Method 1
#define RCR_ENMBID BIT27 // Enable Multiple BssId.
#define RCR_ACKTXBW (BIT24|BIT25) // TXBW Setting of ACK frames
#define RCR_CBSSID BIT23 // Accept BSSID match packet
#define RCR_APWRMGT BIT22 // Accept power management packet
#define RCR_ADD3 BIT21 // Accept address 3 match packet
#define RCR_AMF BIT20 // Accept management type frame
#define RCR_ACF BIT19 // Accept control type frame
#define RCR_ADF BIT18 // Accept data type frame
#define RCR_RXFTH BIT13 // Rx FIFO Threshold
#define RCR_AICV BIT12 // Accept ICV error packet
#define RCR_ACRC32 BIT5 // Accept CRC32 error packet
#define RCR_AB BIT3 // Accept broadcast packet
#define RCR_AM BIT2 // Accept multicast packet
#define RCR_APM BIT1 // Accept physical match packet
#define RCR_AAP BIT0 // Accept all unicast packet
SLOT_TIME = 0x049, // Slot Time Register
ACK_TIMEOUT = 0x04c, // Ack Timeout Register
PIFS_TIME = 0x04d, // PIFS time
USTIME = 0x04e, // Microsecond Tuning Register, Sets the microsecond time unit used by MAC clock.
EDCAPARA_BE = 0x050, // EDCA Parameter of AC BE
EDCAPARA_BK = 0x054, // EDCA Parameter of AC BK
EDCAPARA_VO = 0x058, // EDCA Parameter of AC VO
EDCAPARA_VI = 0x05C, // EDCA Parameter of AC VI
RFPC = 0x05F, // Rx FIFO Packet Count
CWRR = 0x060, // Contention Window Report Register
BCN_TCFG = 0x062, // Beacon Time Configuration
#define BCN_TCFG_CW_SHIFT 8
#define BCN_TCFG_IFS 0
BCN_INTERVAL = 0x070, // Beacon Interval (TU)
ATIMWND = 0x072, // ATIM Window Size (TU)
BCN_DRV_EARLY_INT = 0x074, // Driver Early Interrupt Time (TU). Time to send interrupt to notify to change beacon content before TBTT
BCN_DMATIME = 0x076, // Beacon DMA and ATIM interrupt time (US). Indicates the time before TBTT to perform beacon queue DMA
BCN_ERR_THRESH = 0x078, // Beacon Error Threshold
RWCAM = 0x0A0, //IN 8190 Data Sheet is called CAMcmd
WCAMI = 0x0A4, // Software write CAM input content
RCAMO = 0x0A8, // Software read/write CAM config
SECR = 0x0B0, //Security Configuration Register
#define SCR_TxUseDK BIT0 //Force Tx Use Default Key
#define SCR_RxUseDK BIT1 //Force Rx Use Default Key
#define SCR_TxEncEnable BIT2 //Enable Tx Encryption
#define SCR_RxDecEnable BIT3 //Enable Rx Decryption
#define SCR_SKByA2 BIT4 //Search kEY BY A2
#define SCR_NoSKMC BIT5 //No Key Search for Multicast
#define SCR_UseDK 0x01
#define SCR_TxSecEnable 0x02
#define SCR_RxSecEnable 0x04
TPPoll = 0x0fd, // Transmit priority polling register
PSR = 0x0ff, // Page Select Register
#define CPU_CCK_LOOPBACK 0x00030000
#define CPU_GEN_SYSTEM_RESET 0x00000001
#define CPU_GEN_FIRMWARE_RESET 0x00000008
#define CPU_GEN_BOOT_RDY 0x00000010
#define CPU_GEN_FIRM_RDY 0x00000020
#define CPU_GEN_PUT_CODE_OK 0x00000080
#define CPU_GEN_BB_RST 0x00000100
#define CPU_GEN_PWR_STB_CPU 0x00000004
#define CPU_GEN_NO_LOOPBACK_MSK 0xFFF8FFFF // Set bit18,17,16 to 0. Set bit19
#define CPU_GEN_NO_LOOPBACK_SET 0x00080000 // Set BIT19 to 1
//----------------------------------------------------------------------------
// 8190 CPU General Register (offset 0x100, 4 byte)
//----------------------------------------------------------------------------
#define CPU_CCK_LOOPBACK 0x00030000
#define CPU_GEN_SYSTEM_RESET 0x00000001
#define CPU_GEN_FIRMWARE_RESET 0x00000008
#define CPU_GEN_BOOT_RDY 0x00000010
#define CPU_GEN_FIRM_RDY 0x00000020
#define CPU_GEN_PUT_CODE_OK 0x00000080
#define CPU_GEN_BB_RST 0x00000100
#define CPU_GEN_PWR_STB_CPU 0x00000004
#define CPU_GEN_NO_LOOPBACK_MSK 0xFFF8FFFF // Set bit18,17,16 to 0. Set bit19
#define CPU_GEN_NO_LOOPBACK_SET 0x00080000 // Set BIT19 to 1
CPU_GEN = 0x100, // CPU Reset Register
LED1Cfg = 0x154,// LED1 Configuration Register
LED0Cfg = 0x155,// LED0 Configuration Register
AcmAvg = 0x170, // ACM Average Period Register
AcmHwCtrl = 0x171, // ACM Hardware Control Register
//----------------------------------------------------------------------------
////
//// 8190 AcmHwCtrl bits (offset 0x171, 1 byte)
////----------------------------------------------------------------------------
//
#define AcmHw_HwEn BIT0
#define AcmHw_BeqEn BIT1
#define AcmHw_ViqEn BIT2
#define AcmHw_VoqEn BIT3
#define AcmHw_BeqStatus BIT4
#define AcmHw_ViqStatus BIT5
#define AcmHw_VoqStatus BIT6
AcmFwCtrl = 0x172, // ACM Firmware Control Register
AES_11N_FIX = 0x173,
VOAdmTime = 0x174, // VO Queue Admitted Time Register
VIAdmTime = 0x178, // VI Queue Admitted Time Register
BEAdmTime = 0x17C, // BE Queue Admitted Time Register
RQPN1 = 0x180, // Reserved Queue Page Number , Vo Vi, Be, Bk
RQPN2 = 0x184, // Reserved Queue Page Number, HCCA, Cmd, Mgnt, High
RQPN3 = 0x188, // Reserved Queue Page Number, Bcn, Public,
// QPRR = 0x1E0, // Queue Page Report per TID
QPNR = 0x1D0, //0x1F0, // Queue Packet Number report per TID
BQDA = 0x200, // Beacon Queue Descriptor Address
HQDA = 0x204, // High Priority Queue Descriptor Address
CQDA = 0x208, // Command Queue Descriptor Address
MQDA = 0x20C, // Management Queue Descriptor Address
HCCAQDA = 0x210, // HCCA Queue Descriptor Address
VOQDA = 0x214, // VO Queue Descriptor Address
VIQDA = 0x218, // VI Queue Descriptor Address
BEQDA = 0x21C, // BE Queue Descriptor Address
BKQDA = 0x220, // BK Queue Descriptor Address
RCQDA = 0x224, // Receive command Queue Descriptor Address
RDQDA = 0x228, // Receive Queue Descriptor Start Address
MAR0 = 0x240, // Multicast filter.
MAR4 = 0x244,
CCX_PERIOD = 0x250, // CCX Measurement Period Register, in unit of TU.
CLM_RESULT = 0x251, // CCA Busy fraction register.
NHM_PERIOD = 0x252, // NHM Measurement Period register, in unit of TU.
NHM_THRESHOLD0 = 0x253, // Noise Histogram Meashorement0.
NHM_THRESHOLD1 = 0x254, // Noise Histogram Meashorement1.
NHM_THRESHOLD2 = 0x255, // Noise Histogram Meashorement2.
NHM_THRESHOLD3 = 0x256, // Noise Histogram Meashorement3.
NHM_THRESHOLD4 = 0x257, // Noise Histogram Meashorement4.
NHM_THRESHOLD5 = 0x258, // Noise Histogram Meashorement5.
NHM_THRESHOLD6 = 0x259, // Noise Histogram Meashorement6
MCTRL = 0x25A, // Measurement Control
NHM_RPI_COUNTER0 = 0x264, // Noise Histogram RPI counter0, the fraction of signal strength < NHM_THRESHOLD0.
NHM_RPI_COUNTER1 = 0x265, // Noise Histogram RPI counter1, the fraction of signal strength in (NHM_THRESHOLD0, NHM_THRESHOLD1].
NHM_RPI_COUNTER2 = 0x266, // Noise Histogram RPI counter2, the fraction of signal strength in (NHM_THRESHOLD1, NHM_THRESHOLD2].
NHM_RPI_COUNTER3 = 0x267, // Noise Histogram RPI counter3, the fraction of signal strength in (NHM_THRESHOLD2, NHM_THRESHOLD3].
NHM_RPI_COUNTER4 = 0x268, // Noise Histogram RPI counter4, the fraction of signal strength in (NHM_THRESHOLD3, NHM_THRESHOLD4].
NHM_RPI_COUNTER5 = 0x269, // Noise Histogram RPI counter5, the fraction of signal strength in (NHM_THRESHOLD4, NHM_THRESHOLD5].
NHM_RPI_COUNTER6 = 0x26A, // Noise Histogram RPI counter6, the fraction of signal strength in (NHM_THRESHOLD5, NHM_THRESHOLD6].
NHM_RPI_COUNTER7 = 0x26B, // Noise Histogram RPI counter7, the fraction of signal strength in (NHM_THRESHOLD6, NHM_THRESHOLD7].
#define BW_OPMODE_11J BIT0
#define BW_OPMODE_5G BIT1
#define BW_OPMODE_20MHZ BIT2
BW_OPMODE = 0x300, // Bandwidth operation mode
MSR = 0x303, // Media Status register
#define MSR_LINK_MASK ((1<<0)|(1<<1))
#define MSR_LINK_MANAGED 2
#define MSR_LINK_NONE 0
#define MSR_LINK_SHIFT 0
#define MSR_LINK_ADHOC 1
#define MSR_LINK_MASTER 3
#define MSR_LINK_ENEDCA (1<<4)
RETRY_LIMIT = 0x304, // Retry Limit [15:8]-short, [7:0]-long
#define RETRY_LIMIT_SHORT_SHIFT 8
#define RETRY_LIMIT_LONG_SHIFT 0
TSFR = 0x308,
RRSR = 0x310, // Response Rate Set
#define RRSR_RSC_OFFSET 21
#define RRSR_SHORT_OFFSET 23
#define RRSR_RSC_DUPLICATE 0x600000
#define RRSR_RSC_LOWSUBCHNL 0x400000
#define RRSR_RSC_UPSUBCHANL 0x200000
#define RRSR_SHORT 0x800000
#define RRSR_1M BIT0
#define RRSR_2M BIT1
#define RRSR_5_5M BIT2
#define RRSR_11M BIT3
#define RRSR_6M BIT4
#define RRSR_9M BIT5
#define RRSR_12M BIT6
#define RRSR_18M BIT7
#define RRSR_24M BIT8
#define RRSR_36M BIT9
#define RRSR_48M BIT10
#define RRSR_54M BIT11
#define RRSR_MCS0 BIT12
#define RRSR_MCS1 BIT13
#define RRSR_MCS2 BIT14
#define RRSR_MCS3 BIT15
#define RRSR_MCS4 BIT16
#define RRSR_MCS5 BIT17
#define RRSR_MCS6 BIT18
#define RRSR_MCS7 BIT19
#define BRSR_AckShortPmb BIT23 // CCK ACK: use Short Preamble or not.
RATR0 = 0x320, // Rate Adaptive Table register1
UFWP = 0x318,
DRIVER_RSSI = 0x32c, // Driver tell Firmware current RSSI
//----------------------------------------------------------------------------
// 8190 Rate Adaptive Table Register (offset 0x320, 4 byte)
//----------------------------------------------------------------------------
//CCK
#define RATR_1M 0x00000001
#define RATR_2M 0x00000002
#define RATR_55M 0x00000004
#define RATR_11M 0x00000008
//OFDM
#define RATR_6M 0x00000010
#define RATR_9M 0x00000020
#define RATR_12M 0x00000040
#define RATR_18M 0x00000080
#define RATR_24M 0x00000100
#define RATR_36M 0x00000200
#define RATR_48M 0x00000400
#define RATR_54M 0x00000800
//MCS 1 Spatial Stream
#define RATR_MCS0 0x00001000
#define RATR_MCS1 0x00002000
#define RATR_MCS2 0x00004000
#define RATR_MCS3 0x00008000
#define RATR_MCS4 0x00010000
#define RATR_MCS5 0x00020000
#define RATR_MCS6 0x00040000
#define RATR_MCS7 0x00080000
//MCS 2 Spatial Stream
#define RATR_MCS8 0x00100000
#define RATR_MCS9 0x00200000
#define RATR_MCS10 0x00400000
#define RATR_MCS11 0x00800000
#define RATR_MCS12 0x01000000
#define RATR_MCS13 0x02000000
#define RATR_MCS14 0x04000000
#define RATR_MCS15 0x08000000
// ALL CCK Rate
#define RATE_ALL_CCK RATR_1M|RATR_2M|RATR_55M|RATR_11M
#define RATE_ALL_OFDM_AG RATR_6M|RATR_9M|RATR_12M|RATR_18M|RATR_24M\
|RATR_36M|RATR_48M|RATR_54M
#define RATE_ALL_OFDM_1SS RATR_MCS0|RATR_MCS1|RATR_MCS2|RATR_MCS3 | \
RATR_MCS4|RATR_MCS5|RATR_MCS6|RATR_MCS7
#define RATE_ALL_OFDM_2SS RATR_MCS8|RATR_MCS9 |RATR_MCS10|RATR_MCS11| \
RATR_MCS12|RATR_MCS13|RATR_MCS14|RATR_MCS15
MCS_TXAGC = 0x340, // MCS AGC
CCK_TXAGC = 0x348, // CCK AGC
// ISR = 0x350, // Interrupt Status Register
// IMR = 0x354, // Interrupt Mask Register
// IMR_POLL = 0x360,
MacBlkCtrl = 0x403, // Mac block on/off control register
EPROM_CMD = 0xfe58,
#define Cmd9346CR_9356SEL (1<<4)
#define EPROM_CMD_RESERVED_MASK (1<<5)
#define EPROM_CMD_OPERATING_MODE_SHIFT 6
#define EPROM_CMD_OPERATING_MODE_MASK ((1<<7)|(1<<6))
#define EPROM_CMD_CONFIG 0x3
#define EPROM_CMD_NORMAL 0
#define EPROM_CMD_LOAD 1
#define EPROM_CMD_PROGRAM 2
#define EPROM_CS_SHIFT 3
#define EPROM_CK_SHIFT 2
#define EPROM_W_SHIFT 1
#define EPROM_R_SHIFT 0
MAC0 = 0x000,
MAC1 = 0x001,
MAC2 = 0x002,
MAC3 = 0x003,
MAC4 = 0x004,
MAC5 = 0x005,
};
//----------------------------------------------------------------------------
// 818xB AnaParm & AnaParm2 Register
//----------------------------------------------------------------------------
//#define ANAPARM_ASIC_ON 0x45090658
//#define ANAPARM2_ASIC_ON 0x727f3f52
#define GPI 0x108
#define GPO 0x109
#define GPE 0x10a
#endif