- 根目录:
- drivers
- tty
- serial
- 8250
- 8250_hp300.c
/*
* Driver for the 98626/98644/internal serial interface on hp300/hp400
* (based on the National Semiconductor INS8250/NS16550AF/WD16C552 UARTs)
*
* Ported from 2.2 and modified to use the normal 8250 driver
* by Kars de Jong <jongk@linux-m68k.org>, May 2004.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <linux/serial_8250.h>
#include <linux/delay.h>
#include <linux/dio.h>
#include <linux/console.h>
#include <linux/slab.h>
#include <asm/io.h>
#include "8250.h"
#if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI)
#warning CONFIG_8250 defined but neither CONFIG_HPDCA nor CONFIG_HPAPCI defined, are you sure?
#endif
#ifdef CONFIG_HPAPCI
struct hp300_port
{
struct hp300_port *next; /* next port */
int line; /* line (tty) number */
};
static struct hp300_port *hp300_ports;
#endif
#ifdef CONFIG_HPDCA
static int __devinit hpdca_init_one(struct dio_dev *d,
const struct dio_device_id *ent);
static void __devexit hpdca_remove_one(struct dio_dev *d);
static struct dio_device_id hpdca_dio_tbl[] = {
{ DIO_ID_DCA0 },
{ DIO_ID_DCA0REM },
{ DIO_ID_DCA1 },
{ DIO_ID_DCA1REM },
{ 0 }
};
static struct dio_driver hpdca_driver = {
.name = "hpdca",
.id_table = hpdca_dio_tbl,
.probe = hpdca_init_one,
.remove = __devexit_p(hpdca_remove_one),
};
#endif
static unsigned int num_ports;
extern int hp300_uart_scode;
/* Offset to UART registers from base of DCA */
#define UART_OFFSET 17
#define DCA_ID 0x01 /* ID (read), reset (write) */
#define DCA_IC 0x03 /* Interrupt control */
/* Interrupt control */
#define DCA_IC_IE 0x80 /* Master interrupt enable */
#define HPDCA_BAUD_BASE 153600
/* Base address of the Frodo part */
#define FRODO_BASE (0x41c000)
/*
* Where we find the 8250-like APCI ports, and how far apart they are.
*/
#define FRODO_APCIBASE 0x0
#define FRODO_APCISPACE 0x20
#define FRODO_APCI_OFFSET(x) (FRODO_APCIBASE + ((x) * FRODO_APCISPACE))
#define HPAPCI_BAUD_BASE 500400
#ifdef CONFIG_SERIAL_8250_CONSOLE
/*
* Parse the bootinfo to find descriptions for headless console and
* debug serial ports and register them with the 8250 driver.
* This function should be called before serial_console_init() is called
* to make sure the serial console will be available for use. IA-64 kernel
* calls this function from setup_arch() after the EFI and ACPI tables have
* been parsed.
*/
int __init hp300_setup_serial_console(void)
{
int scode;
struct uart_port port;
memset(&port, 0, sizeof(port));
if (hp300_uart_scode < 0 || hp300_uart_scode > DIO_SCMAX)
return 0;
if (DIO_SCINHOLE(hp300_uart_scode))
return 0;
scode = hp300_uart_scode;
/* Memory mapped I/O */
port.iotype = UPIO_MEM;
port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
port.type = PORT_UNKNOWN;
/* Check for APCI console */
if (scode == 256) {
#ifdef CONFIG_HPAPCI
printk(KERN_INFO "Serial console is HP APCI 1\n");
port.uartclk = HPAPCI_BAUD_BASE * 16;
port.mapbase = (FRODO_BASE + FRODO_APCI_OFFSET(1));
port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
port.regshift = 2;
add_preferred_console("ttyS", port.line, "9600n8");
#else
printk(KERN_WARNING "Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n");
return 0;
#endif
} else {
#ifdef CONFIG_HPDCA
unsigned long pa = dio_scodetophysaddr(scode);
if (!pa)
return 0;
printk(KERN_INFO "Serial console is HP DCA at select code %d\n", scode);
port.uartclk = HPDCA_BAUD_BASE * 16;
port.mapbase = (pa + UART_OFFSET);
port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
port.regshift = 1;
port.irq = DIO_IPL(pa + DIO_VIRADDRBASE);
/* Enable board-interrupts */
out_8(pa + DIO_VIRADDRBASE + DCA_IC, DCA_IC_IE);
if (DIO_ID(pa + DIO_VIRADDRBASE) & 0x80)
add_preferred_console("ttyS", port.line, "9600n8");
#else
printk(KERN_WARNING "Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n");
return 0;
#endif
}
if (early_serial_setup(&port) < 0)
printk(KERN_WARNING "hp300_setup_serial_console(): early_serial_setup() failed.\n");
return 0;
}
#endif /* CONFIG_SERIAL_8250_CONSOLE */
#ifdef CONFIG_HPDCA
static int __devinit hpdca_init_one(struct dio_dev *d,
const struct dio_device_id *ent)
{
struct uart_port port;
int line;
#ifdef CONFIG_SERIAL_8250_CONSOLE
if (hp300_uart_scode == d->scode) {
/* Already got it. */
return 0;
}
#endif
memset(&port, 0, sizeof(struct uart_port));
/* Memory mapped I/O */
port.iotype = UPIO_MEM;
port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
port.irq = d->ipl;
port.uartclk = HPDCA_BAUD_BASE * 16;
port.mapbase = (d->resource.start + UART_OFFSET);
port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
port.regshift = 1;
port.dev = &d->dev;
line = serial8250_register_port(&port);
if (line < 0) {
printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
" irq %d failed\n", d->scode, port.irq);
return -ENOMEM;
}
/* Enable board-interrupts */
out_8(d->resource.start + DIO_VIRADDRBASE + DCA_IC, DCA_IC_IE);
dio_set_drvdata(d, (void *)line);
/* Reset the DCA */
out_8(d->resource.start + DIO_VIRADDRBASE + DCA_ID, 0xff);
udelay(100);
num_ports++;
return 0;
}
#endif
static int __init hp300_8250_init(void)
{
static int called;
#ifdef CONFIG_HPAPCI
int line;
unsigned long base;
struct uart_port uport;
struct hp300_port *port;
int i;
#endif
if (called)
return -ENODEV;
called = 1;
if (!MACH_IS_HP300)
return -ENODEV;
#ifdef CONFIG_HPDCA
dio_register_driver(&hpdca_driver);
#endif
#ifdef CONFIG_HPAPCI
if (hp300_model < HP_400) {
if (!num_ports)
return -ENODEV;
return 0;
}
/* These models have the Frodo chip.
* Port 0 is reserved for the Apollo Domain keyboard.
* Port 1 is either the console or the DCA.
*/
for (i = 1; i < 4; i++) {
/* Port 1 is the console on a 425e, on other machines it's
* mapped to DCA.
*/
#ifdef CONFIG_SERIAL_8250_CONSOLE
if (i == 1)
continue;
#endif
/* Create new serial device */
port = kmalloc(sizeof(struct hp300_port), GFP_KERNEL);
if (!port)
return -ENOMEM;
memset(&uport, 0, sizeof(struct uart_port));
base = (FRODO_BASE + FRODO_APCI_OFFSET(i));
/* Memory mapped I/O */
uport.iotype = UPIO_MEM;
uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
| UPF_BOOT_AUTOCONF;
/* XXX - no interrupt support yet */
uport.irq = 0;
uport.uartclk = HPAPCI_BAUD_BASE * 16;
uport.mapbase = base;
uport.membase = (char *)(base + DIO_VIRADDRBASE);
uport.regshift = 2;
line = serial8250_register_port(&uport);
if (line < 0) {
printk(KERN_NOTICE "8250_hp300: register_serial() APCI"
" %d irq %d failed\n", i, uport.irq);
kfree(port);
continue;
}
port->line = line;
port->next = hp300_ports;
hp300_ports = port;
num_ports++;
}
#endif
/* Any boards found? */
if (!num_ports)
return -ENODEV;
return 0;
}
#ifdef CONFIG_HPDCA
static void __devexit hpdca_remove_one(struct dio_dev *d)
{
int line;
line = (int) dio_get_drvdata(d);
if (d->resource.start) {
/* Disable board-interrupts */
out_8(d->resource.start + DIO_VIRADDRBASE + DCA_IC, 0);
}
serial8250_unregister_port(line);
}
#endif
static void __exit hp300_8250_exit(void)
{
#ifdef CONFIG_HPAPCI
struct hp300_port *port, *to_free;
for (port = hp300_ports; port; ) {
serial8250_unregister_port(port->line);
to_free = port;
port = port->next;
kfree(to_free);
}
hp300_ports = NULL;
#endif
#ifdef CONFIG_HPDCA
dio_unregister_driver(&hpdca_driver);
#endif
}
module_init(hp300_8250_init);
module_exit(hp300_8250_exit);
MODULE_DESCRIPTION("HP DCA/APCI serial driver");
MODULE_AUTHOR("Kars de Jong <jongk@linux-m68k.org>");
MODULE_LICENSE("GPL");