/*
* at91-sama5d3_xplained.dts - Device Tree file for the SAMA5D3 Xplained board
*
* Copyright (C) 2014 Atmel,
* 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/dts-v1/;
#include "sama5d36.dtsi"
/ {
model = "SAMA5D3 Xplained";
compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
chosen {
bootargs = "console=ttyS0,115200";
};
memory {
reg = <0x20000000 0x10000000>;
};
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
apb {
mmc0: mmc@f0000000 {
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
status = "okay";
slot@0 {
reg = <0>;
bus-width = <8>;
cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
};
};
spi0: spi@f0004000 {
cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
status = "okay";
};
can0: can@f000c000 {
status = "okay";
};
i2c0: i2c@f0014000 {
pinctrl-0 = <&pinctrl_i2c0_pu>;
status = "okay";
};
i2c1: i2c@f0018000 {
status = "okay";
pmic: act8865@5b {
compatible = "active-semi,act8865";
reg = <0x5b>;
status = "okay";
regulators {
vcc_1v8_reg: DCDC_REG1 {
regulator-name = "VCC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vcc_1v2_reg: DCDC_REG2 {
regulator-name = "VCC_1V2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
vcc_3v3_reg: DCDC_REG3 {
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vddfuse_reg: LDO_REG1 {
regulator-name = "FUSE_2V5";
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
};
vddana_reg: LDO_REG2 {
regulator-name = "VDDANA";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
};
};
};
macb0: ethernet@f0028000 {
phy-mode = "rgmii";
status = "okay";
};
pwm0: pwm@f002c000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm0_pwmh0_0 &pinctrl_pwm0_pwmh1_0>;
status = "okay";
};
usart0: serial@f001c000 {
status = "okay";
};
usart1: serial@f0020000 {
pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
status = "okay";
};
uart0: serial@f0024000 {
status = "okay";
};
mmc1: mmc@f8000000 {
pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
status = "okay";
slot@0 {
reg = <0>;
bus-width = <4>;
cd-gpios = <&pioE 1 GPIO_ACTIVE_HIGH>;
};
};
spi1: spi@f8008000 {
cs-gpios = <&pioC 25 0>;
status = "okay";
};
adc0: adc@f8018000 {
pinctrl-0 = <
&pinctrl_adc0_adtrg
&pinctrl_adc0_ad0
&pinctrl_adc0_ad1
&pinctrl_adc0_ad2
&pinctrl_adc0_ad3
&pinctrl_adc0_ad4
&pinctrl_adc0_ad5
&pinctrl_adc0_ad6
&pinctrl_adc0_ad7
&pinctrl_adc0_ad8
&pinctrl_adc0_ad9
>;
status = "okay";
};
i2c2: i2c@f801c000 {
dmas = <0>, <0>; /* Do not use DMA for i2c2 */
pinctrl-0 = <&pinctrl_i2c2_pu>;
status = "okay";
};
macb1: ethernet@f802c000 {
phy-mode = "rmii";
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ethernet-phy@1 {
reg = <0x1>;
};
};
dbgu: serial@ffffee00 {
status = "okay";
};
pinctrl@fffff200 {
board {
pinctrl_i2c0_pu: i2c0_pu {
atmel,pins =
<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
pinctrl_i2c2_pu: i2c2_pu {
atmel,pins =
<AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>,
<AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
};
pinctrl_key_gpio: key_gpio_0 {
atmel,pins =
<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_mmc0_cd: mmc0_cd {
atmel,pins =
<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_mmc1_cd: mmc1_cd {
atmel,pins =
<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_usba_vbus: usba_vbus {
atmel,pins =
<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PE9, conflicts with A9 */
};
};
};
pmc: pmc@fffffc00 {
main: mainck {
clock-frequency = <12000000>;
};
};
};
nand0: nand@60000000 {
nand-bus-width = <8>;
nand-ecc-mode = "hw";
atmel,has-pmecc;
atmel,pmecc-cap = <4>;
atmel,pmecc-sector-size = <512>;
nand-on-flash-bbt;
status = "okay";
at91bootstrap@0 {
label = "at91bootstrap";
reg = <0x0 0x40000>;
};
bootloader@40000 {
label = "bootloader";
reg = <0x40000 0x80000>;
};
bootloaderenv@c0000 {
label = "bootloader env";
reg = <0xc0000 0xc0000>;
};
dtb@180000 {
label = "device tree";
reg = <0x180000 0x80000>;
};
kernel@200000 {
label = "kernel";
reg = <0x200000 0x600000>;
};
rootfs@800000 {
label = "rootfs";
reg = <0x800000 0x0f800000>;
};
};
usb0: gadget@00500000 {
atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>; /* PE9, conflicts with A9 */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usba_vbus>;
status = "okay";
};
usb1: ohci@00600000 {
num-ports = <3>;
atmel,vbus-gpio = <0
&pioE 3 GPIO_ACTIVE_LOW
&pioE 4 GPIO_ACTIVE_LOW
>;
status = "okay";
};
usb2: ehci@00700000 {
status = "okay";
};
};
gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_key_gpio>;
bp3 {
label = "PB_USER";
gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
linux,code = <0x104>;
gpio-key,wakeup;
};
};
leds {
compatible = "gpio-leds";
d2 {
label = "d2";
gpios = <&pioE 23 GPIO_ACTIVE_LOW>; /* PE23, conflicts with A23, CTS2 */
linux,default-trigger = "heartbeat";
};
d3 {
label = "d3";
gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
};
};
};