/* * Copyright 2011 Freescale Semiconductor, Inc. * Copyright 2011 Linaro Ltd. * * The code contained herein is licensed under the GNU General Public * License. You may obtain a copy of the GNU General Public License * Version 2 or later at the following locations: * * http://www.opensource.org/licenses/gpl-license.html * http://www.gnu.org/copyleft/gpl.html */ #include <dt-bindings/clock/imx6qdl-clock.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include "skeleton.dtsi" / { aliases { ethernet0 = &fec; can0 = &can1; can1 = &can2; gpio0 = &gpio1; gpio1 = &gpio2; gpio2 = &gpio3; gpio3 = &gpio4; gpio4 = &gpio5; gpio5 = &gpio6; gpio6 = &gpio7; i2c0 = &i2c1; i2c1 = &i2c2; i2c2 = &i2c3; mmc0 = &usdhc1; mmc1 = &usdhc2; mmc2 = &usdhc3; mmc3 = &usdhc4; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; serial3 = &uart4; serial4 = &uart5; spi0 = &ecspi1; spi1 = &ecspi2; spi2 = &ecspi3; spi3 = &ecspi4; usbphy0 = &usbphy1; usbphy1 = &usbphy2; }; intc: interrupt-controller@00a01000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <3>; interrupt-controller; reg = <0x00a01000 0x1000>, <0x00a00100 0x100>; interrupt-parent = <&intc>; }; clocks { #address-cells = <1>; #size-cells = <0>; ckil { compatible = "fsl,imx-ckil", "fixed-clock"; #clock-cells = <0>; clock-frequency = <32768>; }; ckih1 { compatible = "fsl,imx-ckih1", "fixed-clock"; #clock-cells = <0>; clock-frequency = <0>; }; osc { compatible = "fsl,imx-osc", "fixed-clock"; #clock-cells = <0>; clock-frequency = <24000000>; }; }; soc { #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; interrupt-parent = <&gpc>; ranges; dma_apbh: dma-apbh@00110000 { compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh"; reg = <0x00110000 0x2000>; interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>, <0 13 IRQ_TYPE_LEVEL_HIGH>, <0 13 IRQ_TYPE_LEVEL_HIGH>, <0 13 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; #dma-cells = <1>; dma-channels = <4>; clocks = <&clks IMX6QDL_CLK_APBH_DMA>; }; gpmi: gpmi-nand@00112000 { compatible = "fsl,imx6q-gpmi-nand"; #address-cells = <1>; #size-cells = <1>; reg = <0x00112000 0x2000>, <0x00114000 0x2000>; reg-names = "gpmi-nand", "bch"; interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "bch"; clocks = <&clks IMX6QDL_CLK_GPMI_IO>, <&clks IMX6QDL_CLK_GPMI_APB>, <&clks IMX6QDL_CLK_GPMI_BCH>, <&clks IMX6QDL_CLK_GPMI_BCH_APB>, <&clks IMX6QDL_CLK_PER1_BCH>; clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch"; dmas = <&dma_apbh 0>; dma-names = "rx-tx"; status = "disabled"; }; timer@00a00600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x00a00600 0x20>; interrupts = <1 13 0xf01>; interrupt-parent = <&intc>; clocks = <&clks IMX6QDL_CLK_TWD>; }; L2: l2-cache@00a02000 { compatible = "arm,pl310-cache"; reg = <0x00a02000 0x1000>; interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>; cache-unified; cache-level = <2>; arm,tag-latency = <4 2 3>; arm,data-latency = <4 2 3>; }; pcie: pcie@0x01000000 { compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; reg = <0x01ffc000 0x04000>, <0x01f00000 0x80000>; reg-names = "dbi", "config"; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */ 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */ num-lanes = <1>; interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "msi"; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_PCIE_AXI>, <&clks IMX6QDL_CLK_LVDS1_GATE>, <&clks IMX6QDL_CLK_PCIE_REF_125M>; clock-names = "pcie", "pcie_bus", "pcie_phy"; status = "disabled"; }; pmu { compatible = "arm,cortex-a9-pmu"; interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>; }; aips-bus@02000000 { /* AIPS1 */ compatible = "fsl,aips-bus", "simple-bus"; #address-cells = <1>; #size-cells = <1>; reg = <0x02000000 0x100000>; ranges; spba-bus@02000000 { compatible = "fsl,spba-bus", "simple-bus"; #address-cells = <1>; #size-cells = <1>; reg = <0x02000000 0x40000>; ranges; spdif: spdif@02004000 { compatible = "fsl,imx35-spdif"; reg = <0x02004000 0x4000>; interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>; dmas = <&sdma 14 18 0>, <&sdma 15 18 0>; dma-names = "rx", "tx"; clocks = <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_DUMMY>; clock-names = "core", "rxtx0", "rxtx1", "rxtx2", "rxtx3", "rxtx4", "rxtx5", "rxtx6", "rxtx7"; status = "disabled"; }; ecspi1: ecspi@02008000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x02008000 0x4000>; interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_ECSPI1>, <&clks IMX6QDL_CLK_ECSPI1>; clock-names = "ipg", "per"; dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; dma-names = "rx", "tx"; status = "disabled"; }; ecspi2: ecspi@0200c000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x0200c000 0x4000>; interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_ECSPI2>, <&clks IMX6QDL_CLK_ECSPI2>; clock-names = "ipg", "per"; dmas = <&sdma 5 7 1>, <&sdma 6 7 2>; dma-names = "rx", "tx"; status = "disabled"; }; ecspi3: ecspi@02010000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x02010000 0x4000>; interrupts = <0 33 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_ECSPI3>, <&clks IMX6QDL_CLK_ECSPI3>; clock-names = "ipg", "per"; dmas = <&sdma 7 7 1>, <&sdma 8 7 2>; dma-names = "rx", "tx"; status = "disabled"; }; ecspi4: ecspi@02014000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x02014000 0x4000>; interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_ECSPI4>, <&clks IMX6QDL_CLK_ECSPI4>; clock-names = "ipg", "per"; dmas = <&sdma 9 7 1>, <&sdma 10 7 2>; dma-names = "rx", "tx"; status = "disabled"; }; uart1: serial@02020000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02020000 0x4000>; interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; dmas = <&sdma 25 4 0>, <&sdma 26 4 0>; dma-names = "rx", "tx"; status = "disabled"; }; esai: esai@02024000 { reg = <0x02024000 0x4000>; interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>; }; ssi1: ssi@02028000 { #sound-dai-cells = <0>; compatible = "fsl,imx6q-ssi", "fsl,imx51-ssi"; reg = <0x02028000 0x4000>; interrupts = <0 46 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_SSI1_IPG>, <&clks IMX6QDL_CLK_SSI1>; clock-names = "ipg", "baud"; dmas = <&sdma 37 1 0>, <&sdma 38 1 0>; dma-names = "rx", "tx"; fsl,fifo-depth = <15>; status = "disabled"; }; ssi2: ssi@0202c000 { #sound-dai-cells = <0>; compatible = "fsl,imx6q-ssi", "fsl,imx51-ssi"; reg = <0x0202c000 0x4000>; interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_SSI2_IPG>, <&clks IMX6QDL_CLK_SSI2>; clock-names = "ipg", "baud"; dmas = <&sdma 41 1 0>, <&sdma 42 1 0>; dma-names = "rx", "tx"; fsl,fifo-depth = <15>; status = "disabled"; }; ssi3: ssi@02030000 { #sound-dai-cells = <0>; compatible = "fsl,imx6q-ssi", "fsl,imx51-ssi"; reg = <0x02030000 0x4000>; interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_SSI3_IPG>, <&clks IMX6QDL_CLK_SSI3>; clock-names = "ipg", "baud"; dmas = <&sdma 45 1 0>, <&sdma 46 1 0>; dma-names = "rx", "tx"; fsl,fifo-depth = <15>; status = "disabled"; }; asrc: asrc@02034000 { reg = <0x02034000 0x4000>; interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>; }; spba@0203c000 { reg = <0x0203c000 0x4000>; }; }; vpu: vpu@02040000 { compatible = "cnm,coda960"; reg = <0x02040000 0x3c000>; interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>, <0 3 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "bit", "jpeg"; clocks = <&clks IMX6QDL_CLK_VPU_AXI>, <&clks IMX6QDL_CLK_MMDC_CH0_AXI>; clock-names = "per", "ahb"; resets = <&src 1>; iram = <&ocram>; }; aipstz@0207c000 { /* AIPSTZ1 */ reg = <0x0207c000 0x4000>; }; pwm1: pwm@02080000 { #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x02080000 0x4000>; interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM1>; clock-names = "ipg", "per"; status = "disabled"; }; pwm2: pwm@02084000 { #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x02084000 0x4000>; interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM2>; clock-names = "ipg", "per"; status = "disabled"; }; pwm3: pwm@02088000 { #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x02088000 0x4000>; interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM3>; clock-names = "ipg", "per"; status = "disabled"; }; pwm4: pwm@0208c000 { #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x0208c000 0x4000>; interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM4>; clock-names = "ipg", "per"; status = "disabled"; }; can1: flexcan@02090000 { compatible = "fsl,imx6q-flexcan"; reg = <0x02090000 0x4000>; interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_CAN1_IPG>, <&clks IMX6QDL_CLK_CAN1_SERIAL>; clock-names = "ipg", "per"; status = "disabled"; }; can2: flexcan@02094000 { compatible = "fsl,imx6q-flexcan"; reg = <0x02094000 0x4000>; interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_CAN2_IPG>, <&clks IMX6QDL_CLK_CAN2_SERIAL>; clock-names = "ipg", "per"; status = "disabled"; }; gpt: gpt@02098000 { compatible = "fsl,imx6q-gpt", "fsl,imx31-gpt"; reg = <0x02098000 0x4000>; interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_GPT_IPG>, <&clks IMX6QDL_CLK_GPT_IPG_PER>, <&clks IMX6QDL_CLK_GPT_3M>; clock-names = "ipg", "per", "osc_per"; }; gpio1: gpio@0209c000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x0209c000 0x4000>; interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>, <0 67 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; gpio2: gpio@020a0000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020a0000 0x4000>; interrupts = <0 68 IRQ_TYPE_LEVEL_HIGH>, <0 69 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; gpio3: gpio@020a4000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020a4000 0x4000>; interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>, <0 71 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; gpio4: gpio@020a8000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020a8000 0x4000>; interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>, <0 73 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; gpio5: gpio@020ac000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020ac000 0x4000>; interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>, <0 75 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; gpio6: gpio@020b0000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020b0000 0x4000>; interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>, <0 77 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; gpio7: gpio@020b4000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020b4000 0x4000>; interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>, <0 79 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; }; kpp: kpp@020b8000 { compatible = "fsl,imx6q-kpp", "fsl,imx21-kpp"; reg = <0x020b8000 0x4000>; interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_IPG>; status = "disabled"; }; wdog1: wdog@020bc000 { compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt"; reg = <0x020bc000 0x4000>; interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_DUMMY>; }; wdog2: wdog@020c0000 { compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt"; reg = <0x020c0000 0x4000>; interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_DUMMY>; status = "disabled"; }; clks: ccm@020c4000 { compatible = "fsl,imx6q-ccm"; reg = <0x020c4000 0x4000>; interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>, <0 88 IRQ_TYPE_LEVEL_HIGH>; #clock-cells = <1>; }; anatop: anatop@020c8000 { compatible = "fsl,imx6q-anatop", "syscon", "simple-bus"; reg = <0x020c8000 0x1000>; interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>, <0 54 IRQ_TYPE_LEVEL_HIGH>, <0 127 IRQ_TYPE_LEVEL_HIGH>; regulator-1p1@110 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd1p1"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <1375000>; regulator-always-on; anatop-reg-offset = <0x110>; anatop-vol-bit-shift = <8>; anatop-vol-bit-width = <5>; anatop-min-bit-val = <4>; anatop-min-voltage = <800000>; anatop-max-voltage = <1375000>; }; regulator-3p0@120 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd3p0"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <3150000>; regulator-always-on; anatop-reg-offset = <0x120>; anatop-vol-bit-shift = <8>; anatop-vol-bit-width = <5>; anatop-min-bit-val = <0>; anatop-min-voltage = <2625000>; anatop-max-voltage = <3400000>; }; regulator-2p5@130 { compatible = "fsl,anatop-regulator"; regulator-name = "vdd2p5"; regulator-min-microvolt = <2000000>; regulator-max-microvolt = <2750000>; regulator-always-on; anatop-reg-offset = <0x130>; anatop-vol-bit-shift = <8>; anatop-vol-bit-width = <5>; anatop-min-bit-val = <0>; anatop-min-voltage = <2000000>; anatop-max-voltage = <2750000>; }; reg_arm: regulator-vddcore@140 { compatible = "fsl,anatop-regulator"; regulator-name = "vddarm"; regulator-min-microvolt = <725000>; regulator-max-microvolt = <1450000>; regulator-always-on; anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <0>; anatop-vol-bit-width = <5>; anatop-delay-reg-offset = <0x170>; anatop-delay-bit-shift = <24>; anatop-delay-bit-width = <2>; anatop-min-bit-val = <1>; anatop-min-voltage = <725000>; anatop-max-voltage = <1450000>; }; reg_pu: regulator-vddpu@140 { compatible = "fsl,anatop-regulator"; regulator-name = "vddpu"; regulator-min-microvolt = <725000>; regulator-max-microvolt = <1450000>; regulator-enable-ramp-delay = <150>; anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <9>; anatop-vol-bit-width = <5>; anatop-delay-reg-offset = <0x170>; anatop-delay-bit-shift = <26>; anatop-delay-bit-width = <2>; anatop-min-bit-val = <1>; anatop-min-voltage = <725000>; anatop-max-voltage = <1450000>; }; reg_soc: regulator-vddsoc@140 { compatible = "fsl,anatop-regulator"; regulator-name = "vddsoc"; regulator-min-microvolt = <725000>; regulator-max-microvolt = <1450000>; regulator-always-on; anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <18>; anatop-vol-bit-width = <5>; anatop-delay-reg-offset = <0x170>; anatop-delay-bit-shift = <28>; anatop-delay-bit-width = <2>; anatop-min-bit-val = <1>; anatop-min-voltage = <725000>; anatop-max-voltage = <1450000>; }; }; tempmon: tempmon { compatible = "fsl,imx6q-tempmon"; interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>; fsl,tempmon = <&anatop>; fsl,tempmon-data = <&ocotp>; clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>; }; usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020c9000 0x1000>; interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBPHY1>; fsl,anatop = <&anatop>; }; usbphy2: usbphy@020ca000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020ca000 0x1000>; interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBPHY2>; fsl,anatop = <&anatop>; }; snvs@020cc000 { compatible = "fsl,sec-v4.0-mon", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0 0x020cc000 0x4000>; snvs_rtc: snvs-rtc-lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; reg = <0x34 0x58>; interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>, <0 20 IRQ_TYPE_LEVEL_HIGH>; }; snvs_poweroff: snvs-poweroff@38 { compatible = "fsl,sec-v4.0-poweroff"; reg = <0x38 0x4>; status = "disabled"; }; }; epit1: epit@020d0000 { /* EPIT1 */ reg = <0x020d0000 0x4000>; interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>; }; epit2: epit@020d4000 { /* EPIT2 */ reg = <0x020d4000 0x4000>; interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>; }; src: src@020d8000 { compatible = "fsl,imx6q-src", "fsl,imx51-src"; reg = <0x020d8000 0x4000>; interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>, <0 96 IRQ_TYPE_LEVEL_HIGH>; #reset-cells = <1>; }; gpc: gpc@020dc000 { compatible = "fsl,imx6q-gpc"; reg = <0x020dc000 0x4000>; interrupt-controller; #interrupt-cells = <3>; interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, <0 90 IRQ_TYPE_LEVEL_HIGH>; interrupt-parent = <&intc>; pu-supply = <®_pu>; clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>, <&clks IMX6QDL_CLK_GPU3D_SHADER>, <&clks IMX6QDL_CLK_GPU2D_CORE>, <&clks IMX6QDL_CLK_GPU2D_AXI>, <&clks IMX6QDL_CLK_OPENVG_AXI>, <&clks IMX6QDL_CLK_VPU_AXI>; #power-domain-cells = <1>; }; gpr: iomuxc-gpr@020e0000 { compatible = "fsl,imx6q-iomuxc-gpr", "syscon"; reg = <0x020e0000 0x38>; }; iomuxc: iomuxc@020e0000 { compatible = "fsl,imx6dl-iomuxc", "fsl,imx6q-iomuxc"; reg = <0x020e0000 0x4000>; }; ldb: ldb@020e0008 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-ldb", "fsl,imx53-ldb"; gpr = <&gpr>; status = "disabled"; lvds-channel@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; status = "disabled"; port@0 { reg = <0>; lvds0_mux_0: endpoint { remote-endpoint = <&ipu1_di0_lvds0>; }; }; port@1 { reg = <1>; lvds0_mux_1: endpoint { remote-endpoint = <&ipu1_di1_lvds0>; }; }; }; lvds-channel@1 { #address-cells = <1>; #size-cells = <0>; reg = <1>; status = "disabled"; port@0 { reg = <0>; lvds1_mux_0: endpoint { remote-endpoint = <&ipu1_di0_lvds1>; }; }; port@1 { reg = <1>; lvds1_mux_1: endpoint { remote-endpoint = <&ipu1_di1_lvds1>; }; }; }; }; hdmi: hdmi@0120000 { #address-cells = <1>; #size-cells = <0>; reg = <0x00120000 0x9000>; interrupts = <0 115 0x04>; gpr = <&gpr>; clocks = <&clks IMX6QDL_CLK_HDMI_IAHB>, <&clks IMX6QDL_CLK_HDMI_ISFR>; clock-names = "iahb", "isfr"; status = "disabled"; port@0 { reg = <0>; hdmi_mux_0: endpoint { remote-endpoint = <&ipu1_di0_hdmi>; }; }; port@1 { reg = <1>; hdmi_mux_1: endpoint { remote-endpoint = <&ipu1_di1_hdmi>; }; }; }; dcic1: dcic@020e4000 { reg = <0x020e4000 0x4000>; interrupts = <0 124 IRQ_TYPE_LEVEL_HIGH>; }; dcic2: dcic@020e8000 { reg = <0x020e8000 0x4000>; interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>; }; sdma: sdma@020ec000 { compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma"; reg = <0x020ec000 0x4000>; interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_SDMA>, <&clks IMX6QDL_CLK_SDMA>; clock-names = "ipg", "ahb"; #dma-cells = <3>; fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin"; }; }; aips-bus@02100000 { /* AIPS2 */ compatible = "fsl,aips-bus", "simple-bus"; #address-cells = <1>; #size-cells = <1>; reg = <0x02100000 0x100000>; ranges; caam@02100000 { reg = <0x02100000 0x40000>; interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>, <0 106 IRQ_TYPE_LEVEL_HIGH>; }; aipstz@0217c000 { /* AIPSTZ2 */ reg = <0x0217c000 0x4000>; }; usbotg: usb@02184000 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184000 0x200>; interrupts = <0 43 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; status = "disabled"; }; usbh1: usb@02184200 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184200 0x200>; interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; dr_mode = "host"; status = "disabled"; }; usbh2: usb@02184400 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184400 0x200>; interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 2>; dr_mode = "host"; status = "disabled"; }; usbh3: usb@02184600 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184600 0x200>; interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 3>; dr_mode = "host"; status = "disabled"; }; usbmisc: usbmisc@02184800 { #index-cells = <1>; compatible = "fsl,imx6q-usbmisc"; reg = <0x02184800 0x200>; clocks = <&clks IMX6QDL_CLK_USBOH3>; }; fec: ethernet@02188000 { compatible = "fsl,imx6q-fec"; reg = <0x02188000 0x4000>; interrupts-extended = <&intc 0 118 IRQ_TYPE_LEVEL_HIGH>, <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET_REF>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; }; mlb@0218c000 { reg = <0x0218c000 0x4000>; interrupts = <0 53 IRQ_TYPE_LEVEL_HIGH>, <0 117 IRQ_TYPE_LEVEL_HIGH>, <0 126 IRQ_TYPE_LEVEL_HIGH>; }; usdhc1: usdhc@02190000 { compatible = "fsl,imx6q-usdhc"; reg = <0x02190000 0x4000>; interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USDHC1>, <&clks IMX6QDL_CLK_USDHC1>, <&clks IMX6QDL_CLK_USDHC1>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; }; usdhc2: usdhc@02194000 { compatible = "fsl,imx6q-usdhc"; reg = <0x02194000 0x4000>; interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USDHC2>, <&clks IMX6QDL_CLK_USDHC2>, <&clks IMX6QDL_CLK_USDHC2>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; }; usdhc3: usdhc@02198000 { compatible = "fsl,imx6q-usdhc"; reg = <0x02198000 0x4000>; interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USDHC3>, <&clks IMX6QDL_CLK_USDHC3>, <&clks IMX6QDL_CLK_USDHC3>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; }; usdhc4: usdhc@0219c000 { compatible = "fsl,imx6q-usdhc"; reg = <0x0219c000 0x4000>; interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USDHC4>, <&clks IMX6QDL_CLK_USDHC4>, <&clks IMX6QDL_CLK_USDHC4>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; }; i2c1: i2c@021a0000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; reg = <0x021a0000 0x4000>; interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_I2C1>; status = "disabled"; }; i2c2: i2c@021a4000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; reg = <0x021a4000 0x4000>; interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_I2C2>; status = "disabled"; }; i2c3: i2c@021a8000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; reg = <0x021a8000 0x4000>; interrupts = <0 38 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_I2C3>; status = "disabled"; }; romcp@021ac000 { reg = <0x021ac000 0x4000>; }; mmdc0: mmdc@021b0000 { /* MMDC0 */ compatible = "fsl,imx6q-mmdc"; reg = <0x021b0000 0x4000>; }; mmdc1: mmdc@021b4000 { /* MMDC1 */ reg = <0x021b4000 0x4000>; }; weim: weim@021b8000 { compatible = "fsl,imx6q-weim"; reg = <0x021b8000 0x4000>; interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_EIM_SLOW>; }; ocotp: ocotp@021bc000 { compatible = "fsl,imx6q-ocotp", "syscon"; reg = <0x021bc000 0x4000>; }; tzasc@021d0000 { /* TZASC1 */ reg = <0x021d0000 0x4000>; interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; }; tzasc@021d4000 { /* TZASC2 */ reg = <0x021d4000 0x4000>; interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>; }; audmux: audmux@021d8000 { compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux"; reg = <0x021d8000 0x4000>; status = "disabled"; }; mipi_csi: mipi@021dc000 { reg = <0x021dc000 0x4000>; }; mipi_dsi: mipi@021e0000 { #address-cells = <1>; #size-cells = <0>; reg = <0x021e0000 0x4000>; status = "disabled"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; mipi_mux_0: endpoint { remote-endpoint = <&ipu1_di0_mipi>; }; }; port@1 { reg = <1>; mipi_mux_1: endpoint { remote-endpoint = <&ipu1_di1_mipi>; }; }; }; }; vdoa@021e4000 { reg = <0x021e4000 0x4000>; interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; }; uart2: serial@021e8000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021e8000 0x4000>; interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; dmas = <&sdma 27 4 0>, <&sdma 28 4 0>; dma-names = "rx", "tx"; status = "disabled"; }; uart3: serial@021ec000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021ec000 0x4000>; interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; dmas = <&sdma 29 4 0>, <&sdma 30 4 0>; dma-names = "rx", "tx"; status = "disabled"; }; uart4: serial@021f0000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021f0000 0x4000>; interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; dmas = <&sdma 31 4 0>, <&sdma 32 4 0>; dma-names = "rx", "tx"; status = "disabled"; }; uart5: serial@021f4000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021f4000 0x4000>; interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; dmas = <&sdma 33 4 0>, <&sdma 34 4 0>; dma-names = "rx", "tx"; status = "disabled"; }; }; ipu1: ipu@02400000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx6q-ipu"; reg = <0x02400000 0x400000>; interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>, <0 5 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_IPU1>, <&clks IMX6QDL_CLK_IPU1_DI0>, <&clks IMX6QDL_CLK_IPU1_DI1>; clock-names = "bus", "di0", "di1"; resets = <&src 2>; ipu1_csi0: port@0 { reg = <0>; }; ipu1_csi1: port@1 { reg = <1>; }; ipu1_di0: port@2 { #address-cells = <1>; #size-cells = <0>; reg = <2>; ipu1_di0_disp0: endpoint@0 { }; ipu1_di0_hdmi: endpoint@1 { remote-endpoint = <&hdmi_mux_0>; }; ipu1_di0_mipi: endpoint@2 { remote-endpoint = <&mipi_mux_0>; }; ipu1_di0_lvds0: endpoint@3 { remote-endpoint = <&lvds0_mux_0>; }; ipu1_di0_lvds1: endpoint@4 { remote-endpoint = <&lvds1_mux_0>; }; }; ipu1_di1: port@3 { #address-cells = <1>; #size-cells = <0>; reg = <3>; ipu1_di0_disp1: endpoint@0 { }; ipu1_di1_hdmi: endpoint@1 { remote-endpoint = <&hdmi_mux_1>; }; ipu1_di1_mipi: endpoint@2 { remote-endpoint = <&mipi_mux_1>; }; ipu1_di1_lvds0: endpoint@3 { remote-endpoint = <&lvds0_mux_1>; }; ipu1_di1_lvds1: endpoint@4 { remote-endpoint = <&lvds1_mux_1>; }; }; }; }; };