- 根目录:
- drivers
- power
- smb347-charger.c
/*
* Summit Microelectronics SMB347 Battery Charger Driver
*
* Copyright (C) 2011, Intel Corporation
*
* Authors: Bruce E. Robertson <bruce.e.robertson@intel.com>
* Mika Westerberg <mika.westerberg@linux.intel.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/err.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/i2c.h>
#include <linux/mutex.h>
#include <linux/power_supply.h>
#include <linux/power/smb347-charger.h>
#include <linux/regmap.h>
/*
* Configuration registers. These are mirrored to volatile RAM and can be
* written once %CMD_A_ALLOW_WRITE is set in %CMD_A register. They will be
* reloaded from non-volatile registers after POR.
*/
#define CFG_CHARGE_CURRENT 0x00
#define CFG_CHARGE_CURRENT_FCC_MASK 0xe0
#define CFG_CHARGE_CURRENT_FCC_SHIFT 5
#define CFG_CHARGE_CURRENT_PCC_MASK 0x18
#define CFG_CHARGE_CURRENT_PCC_SHIFT 3
#define CFG_CHARGE_CURRENT_TC_MASK 0x07
#define CFG_CURRENT_LIMIT 0x01
#define CFG_CURRENT_LIMIT_DC_MASK 0xf0
#define CFG_CURRENT_LIMIT_DC_SHIFT 4
#define CFG_CURRENT_LIMIT_USB_MASK 0x0f
#define CFG_FLOAT_VOLTAGE 0x03
#define CFG_FLOAT_VOLTAGE_FLOAT_MASK 0x3f
#define CFG_FLOAT_VOLTAGE_THRESHOLD_MASK 0xc0
#define CFG_FLOAT_VOLTAGE_THRESHOLD_SHIFT 6
#define CFG_STAT 0x05
#define CFG_STAT_DISABLED BIT(5)
#define CFG_STAT_ACTIVE_HIGH BIT(7)
#define CFG_PIN 0x06
#define CFG_PIN_EN_CTRL_MASK 0x60
#define CFG_PIN_EN_CTRL_ACTIVE_HIGH 0x40
#define CFG_PIN_EN_CTRL_ACTIVE_LOW 0x60
#define CFG_PIN_EN_APSD_IRQ BIT(1)
#define CFG_PIN_EN_CHARGER_ERROR BIT(2)
#define CFG_THERM 0x07
#define CFG_THERM_SOFT_HOT_COMPENSATION_MASK 0x03
#define CFG_THERM_SOFT_HOT_COMPENSATION_SHIFT 0
#define CFG_THERM_SOFT_COLD_COMPENSATION_MASK 0x0c
#define CFG_THERM_SOFT_COLD_COMPENSATION_SHIFT 2
#define CFG_THERM_MONITOR_DISABLED BIT(4)
#define CFG_SYSOK 0x08
#define CFG_SYSOK_SUSPEND_HARD_LIMIT_DISABLED BIT(2)
#define CFG_OTHER 0x09
#define CFG_OTHER_RID_MASK 0xc0
#define CFG_OTHER_RID_ENABLED_AUTO_OTG 0xc0
#define CFG_OTG 0x0a
#define CFG_OTG_TEMP_THRESHOLD_MASK 0x30
#define CFG_OTG_TEMP_THRESHOLD_SHIFT 4
#define CFG_OTG_CC_COMPENSATION_MASK 0xc0
#define CFG_OTG_CC_COMPENSATION_SHIFT 6
#define CFG_TEMP_LIMIT 0x0b
#define CFG_TEMP_LIMIT_SOFT_HOT_MASK 0x03
#define CFG_TEMP_LIMIT_SOFT_HOT_SHIFT 0
#define CFG_TEMP_LIMIT_SOFT_COLD_MASK 0x0c
#define CFG_TEMP_LIMIT_SOFT_COLD_SHIFT 2
#define CFG_TEMP_LIMIT_HARD_HOT_MASK 0x30
#define CFG_TEMP_LIMIT_HARD_HOT_SHIFT 4
#define CFG_TEMP_LIMIT_HARD_COLD_MASK 0xc0
#define CFG_TEMP_LIMIT_HARD_COLD_SHIFT 6
#define CFG_FAULT_IRQ 0x0c
#define CFG_FAULT_IRQ_DCIN_UV BIT(2)
#define CFG_STATUS_IRQ 0x0d
#define CFG_STATUS_IRQ_TERMINATION_OR_TAPER BIT(4)
#define CFG_STATUS_IRQ_CHARGE_TIMEOUT BIT(7)
#define CFG_ADDRESS 0x0e
/* Command registers */
#define CMD_A 0x30
#define CMD_A_CHG_ENABLED BIT(1)
#define CMD_A_SUSPEND_ENABLED BIT(2)
#define CMD_A_ALLOW_WRITE BIT(7)
#define CMD_B 0x31
#define CMD_C 0x33
/* Interrupt Status registers */
#define IRQSTAT_A 0x35
#define IRQSTAT_C 0x37
#define IRQSTAT_C_TERMINATION_STAT BIT(0)
#define IRQSTAT_C_TERMINATION_IRQ BIT(1)
#define IRQSTAT_C_TAPER_IRQ BIT(3)
#define IRQSTAT_D 0x38
#define IRQSTAT_D_CHARGE_TIMEOUT_STAT BIT(2)
#define IRQSTAT_D_CHARGE_TIMEOUT_IRQ BIT(3)
#define IRQSTAT_E 0x39
#define IRQSTAT_E_USBIN_UV_STAT BIT(0)
#define IRQSTAT_E_USBIN_UV_IRQ BIT(1)
#define IRQSTAT_E_DCIN_UV_STAT BIT(4)
#define IRQSTAT_E_DCIN_UV_IRQ BIT(5)
#define IRQSTAT_F 0x3a
/* Status registers */
#define STAT_A 0x3b
#define STAT_A_FLOAT_VOLTAGE_MASK 0x3f
#define STAT_B 0x3c
#define STAT_C 0x3d
#define STAT_C_CHG_ENABLED BIT(0)
#define STAT_C_HOLDOFF_STAT BIT(3)
#define STAT_C_CHG_MASK 0x06
#define STAT_C_CHG_SHIFT 1
#define STAT_C_CHG_TERM BIT(5)
#define STAT_C_CHARGER_ERROR BIT(6)
#define STAT_E 0x3f
#define SMB347_MAX_REGISTER 0x3f
/**
* struct smb347_charger - smb347 charger instance
* @lock: protects concurrent access to online variables
* @dev: pointer to device
* @regmap: pointer to driver regmap
* @mains: power_supply instance for AC/DC power
* @usb: power_supply instance for USB power
* @battery: power_supply instance for battery
* @mains_online: is AC/DC input connected
* @usb_online: is USB input connected
* @charging_enabled: is charging enabled
* @pdata: pointer to platform data
*/
struct smb347_charger {
struct mutex lock;
struct device *dev;
struct regmap *regmap;
struct power_supply *mains;
struct power_supply *usb;
struct power_supply *battery;
bool mains_online;
bool usb_online;
bool charging_enabled;
const struct smb347_charger_platform_data *pdata;
};
/* Fast charge current in uA */
static const unsigned int fcc_tbl[] = {
700000,
900000,
1200000,
1500000,
1800000,
2000000,
2200000,
2500000,
};
/* Pre-charge current in uA */
static const unsigned int pcc_tbl[] = {
100000,
150000,
200000,
250000,
};
/* Termination current in uA */
static const unsigned int tc_tbl[] = {
37500,
50000,
100000,
150000,
200000,
250000,
500000,
600000,
};
/* Input current limit in uA */
static const unsigned int icl_tbl[] = {
300000,
500000,
700000,
900000,
1200000,
1500000,
1800000,
2000000,
2200000,
2500000,
};
/* Charge current compensation in uA */
static const unsigned int ccc_tbl[] = {
250000,
700000,
900000,
1200000,
};
/* Convert register value to current using lookup table */
static int hw_to_current(const unsigned int *tbl, size_t size, unsigned int val)
{
if (val >= size)
return -EINVAL;
return tbl[val];
}
/* Convert current to register value using lookup table */
static int current_to_hw(const unsigned int *tbl, size_t size, unsigned int val)
{
size_t i;
for (i = 0; i < size; i++)
if (val < tbl[i])
break;
return i > 0 ? i - 1 : -EINVAL;
}
/**
* smb347_update_ps_status - refreshes the power source status
* @smb: pointer to smb347 charger instance
*
* Function checks whether any power source is connected to the charger and
* updates internal state accordingly. If there is a change to previous state
* function returns %1, otherwise %0 and negative errno in case of errror.
*/
static int smb347_update_ps_status(struct smb347_charger *smb)
{
bool usb = false;
bool dc = false;
unsigned int val;
int ret;
ret = regmap_read(smb->regmap, IRQSTAT_E, &val);
if (ret < 0)
return ret;
/*
* Dc and usb are set depending on whether they are enabled in
* platform data _and_ whether corresponding undervoltage is set.
*/
if (smb->pdata->use_mains)
dc = !(val & IRQSTAT_E_DCIN_UV_STAT);
if (smb->pdata->use_usb)
usb = !(val & IRQSTAT_E_USBIN_UV_STAT);
mutex_lock(&smb->lock);
ret = smb->mains_online != dc || smb->usb_online != usb;
smb->mains_online = dc;
smb->usb_online = usb;
mutex_unlock(&smb->lock);
return ret;
}
/*
* smb347_is_ps_online - returns whether input power source is connected
* @smb: pointer to smb347 charger instance
*
* Returns %true if input power source is connected. Note that this is
* dependent on what platform has configured for usable power sources. For
* example if USB is disabled, this will return %false even if the USB cable
* is connected.
*/
static bool smb347_is_ps_online(struct smb347_charger *smb)
{
bool ret;
mutex_lock(&smb->lock);
ret = smb->usb_online || smb->mains_online;
mutex_unlock(&smb->lock);
return ret;
}
/**
* smb347_charging_status - returns status of charging
* @smb: pointer to smb347 charger instance
*
* Function returns charging status. %0 means no charging is in progress,
* %1 means pre-charging, %2 fast-charging and %3 taper-charging.
*/
static int smb347_charging_status(struct smb347_charger *smb)
{
unsigned int val;
int ret;
if (!smb347_is_ps_online(smb))
return 0;
ret = regmap_read(smb->regmap, STAT_C, &val);
if (ret < 0)
return 0;
return (val & STAT_C_CHG_MASK) >> STAT_C_CHG_SHIFT;
}
static int smb347_charging_set(struct smb347_charger *smb, bool enable)
{
int ret = 0;
if (smb->pdata->enable_control != SMB347_CHG_ENABLE_SW) {
dev_dbg(smb->dev, "charging enable/disable in SW disabled\n");
return 0;
}
mutex_lock(&smb->lock);
if (smb->charging_enabled != enable) {
ret = regmap_update_bits(smb->regmap, CMD_A, CMD_A_CHG_ENABLED,
enable ? CMD_A_CHG_ENABLED : 0);
if (!ret)
smb->charging_enabled = enable;
}
mutex_unlock(&smb->lock);
return ret;
}
static inline int smb347_charging_enable(struct smb347_charger *smb)
{
return smb347_charging_set(smb, true);
}
static inline int smb347_charging_disable(struct smb347_charger *smb)
{
return smb347_charging_set(smb, false);
}
static int smb347_start_stop_charging(struct smb347_charger *smb)
{
int ret;
/*
* Depending on whether valid power source is connected or not, we
* disable or enable the charging. We do it manually because it
* depends on how the platform has configured the valid inputs.
*/
if (smb347_is_ps_online(smb)) {
ret = smb347_charging_enable(smb);
if (ret < 0)
dev_err(smb->dev, "failed to enable charging\n");
} else {
ret = smb347_charging_disable(smb);
if (ret < 0)
dev_err(smb->dev, "failed to disable charging\n");
}
return ret;
}
static int smb347_set_charge_current(struct smb347_charger *smb)
{
int ret;
if (smb->pdata->max_charge_current) {
ret = current_to_hw(fcc_tbl, ARRAY_SIZE(fcc_tbl),
smb->pdata->max_charge_current);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
CFG_CHARGE_CURRENT_FCC_MASK,
ret << CFG_CHARGE_CURRENT_FCC_SHIFT);
if (ret < 0)
return ret;
}
if (smb->pdata->pre_charge_current) {
ret = current_to_hw(pcc_tbl, ARRAY_SIZE(pcc_tbl),
smb->pdata->pre_charge_current);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
CFG_CHARGE_CURRENT_PCC_MASK,
ret << CFG_CHARGE_CURRENT_PCC_SHIFT);
if (ret < 0)
return ret;
}
if (smb->pdata->termination_current) {
ret = current_to_hw(tc_tbl, ARRAY_SIZE(tc_tbl),
smb->pdata->termination_current);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
CFG_CHARGE_CURRENT_TC_MASK, ret);
if (ret < 0)
return ret;
}
return 0;
}
static int smb347_set_current_limits(struct smb347_charger *smb)
{
int ret;
if (smb->pdata->mains_current_limit) {
ret = current_to_hw(icl_tbl, ARRAY_SIZE(icl_tbl),
smb->pdata->mains_current_limit);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CURRENT_LIMIT,
CFG_CURRENT_LIMIT_DC_MASK,
ret << CFG_CURRENT_LIMIT_DC_SHIFT);
if (ret < 0)
return ret;
}
if (smb->pdata->usb_hc_current_limit) {
ret = current_to_hw(icl_tbl, ARRAY_SIZE(icl_tbl),
smb->pdata->usb_hc_current_limit);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CURRENT_LIMIT,
CFG_CURRENT_LIMIT_USB_MASK, ret);
if (ret < 0)
return ret;
}
return 0;
}
static int smb347_set_voltage_limits(struct smb347_charger *smb)
{
int ret;
if (smb->pdata->pre_to_fast_voltage) {
ret = smb->pdata->pre_to_fast_voltage;
/* uV */
ret = clamp_val(ret, 2400000, 3000000) - 2400000;
ret /= 200000;
ret = regmap_update_bits(smb->regmap, CFG_FLOAT_VOLTAGE,
CFG_FLOAT_VOLTAGE_THRESHOLD_MASK,
ret << CFG_FLOAT_VOLTAGE_THRESHOLD_SHIFT);
if (ret < 0)
return ret;
}
if (smb->pdata->max_charge_voltage) {
ret = smb->pdata->max_charge_voltage;
/* uV */
ret = clamp_val(ret, 3500000, 4500000) - 3500000;
ret /= 20000;
ret = regmap_update_bits(smb->regmap, CFG_FLOAT_VOLTAGE,
CFG_FLOAT_VOLTAGE_FLOAT_MASK, ret);
if (ret < 0)
return ret;
}
return 0;
}
static int smb347_set_temp_limits(struct smb347_charger *smb)
{
bool enable_therm_monitor = false;
int ret = 0;
int val;
if (smb->pdata->chip_temp_threshold) {
val = smb->pdata->chip_temp_threshold;
/* degree C */
val = clamp_val(val, 100, 130) - 100;
val /= 10;
ret = regmap_update_bits(smb->regmap, CFG_OTG,
CFG_OTG_TEMP_THRESHOLD_MASK,
val << CFG_OTG_TEMP_THRESHOLD_SHIFT);
if (ret < 0)
return ret;
}
if (smb->pdata->soft_cold_temp_limit != SMB347_TEMP_USE_DEFAULT) {
val = smb->pdata->soft_cold_temp_limit;
val = clamp_val(val, 0, 15);
val /= 5;
/* this goes from higher to lower so invert the value */
val = ~val & 0x3;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_SOFT_COLD_MASK,
val << CFG_TEMP_LIMIT_SOFT_COLD_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
if (smb->pdata->soft_hot_temp_limit != SMB347_TEMP_USE_DEFAULT) {
val = smb->pdata->soft_hot_temp_limit;
val = clamp_val(val, 40, 55) - 40;
val /= 5;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_SOFT_HOT_MASK,
val << CFG_TEMP_LIMIT_SOFT_HOT_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
if (smb->pdata->hard_cold_temp_limit != SMB347_TEMP_USE_DEFAULT) {
val = smb->pdata->hard_cold_temp_limit;
val = clamp_val(val, -5, 10) + 5;
val /= 5;
/* this goes from higher to lower so invert the value */
val = ~val & 0x3;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_HARD_COLD_MASK,
val << CFG_TEMP_LIMIT_HARD_COLD_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
if (smb->pdata->hard_hot_temp_limit != SMB347_TEMP_USE_DEFAULT) {
val = smb->pdata->hard_hot_temp_limit;
val = clamp_val(val, 50, 65) - 50;
val /= 5;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_HARD_HOT_MASK,
val << CFG_TEMP_LIMIT_HARD_HOT_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
/*
* If any of the temperature limits are set, we also enable the
* thermistor monitoring.
*
* When soft limits are hit, the device will start to compensate
* current and/or voltage depending on the configuration.
*
* When hard limit is hit, the device will suspend charging
* depending on the configuration.
*/
if (enable_therm_monitor) {
ret = regmap_update_bits(smb->regmap, CFG_THERM,
CFG_THERM_MONITOR_DISABLED, 0);
if (ret < 0)
return ret;
}
if (smb->pdata->suspend_on_hard_temp_limit) {
ret = regmap_update_bits(smb->regmap, CFG_SYSOK,
CFG_SYSOK_SUSPEND_HARD_LIMIT_DISABLED, 0);
if (ret < 0)
return ret;
}
if (smb->pdata->soft_temp_limit_compensation !=
SMB347_SOFT_TEMP_COMPENSATE_DEFAULT) {
val = smb->pdata->soft_temp_limit_compensation & 0x3;
ret = regmap_update_bits(smb->regmap, CFG_THERM,
CFG_THERM_SOFT_HOT_COMPENSATION_MASK,
val << CFG_THERM_SOFT_HOT_COMPENSATION_SHIFT);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_THERM,
CFG_THERM_SOFT_COLD_COMPENSATION_MASK,
val << CFG_THERM_SOFT_COLD_COMPENSATION_SHIFT);
if (ret < 0)
return ret;
}
if (smb->pdata->charge_current_compensation) {
val = current_to_hw(ccc_tbl, ARRAY_SIZE(ccc_tbl),
smb->pdata->charge_current_compensation);
if (val < 0)
return val;
ret = regmap_update_bits(smb->regmap, CFG_OTG,
CFG_OTG_CC_COMPENSATION_MASK,
(val & 0x3) << CFG_OTG_CC_COMPENSATION_SHIFT);
if (ret < 0)
return ret;
}
return ret;
}
/*
* smb347_set_writable - enables/disables writing to non-volatile registers
* @smb: pointer to smb347 charger instance
*
* You can enable/disable writing to the non-volatile configuration
* registers by calling this function.
*
* Returns %0 on success and negative errno in case of failure.
*/
static int smb347_set_writable(struct smb347_charger *smb, bool writable)
{
return regmap_update_bits(smb->regmap, CMD_A, CMD_A_ALLOW_WRITE,
writable ? CMD_A_ALLOW_WRITE : 0);
}
static int smb347_hw_init(struct smb347_charger *smb)
{
unsigned int val;
int ret;
ret = smb347_set_writable(smb, true);
if (ret < 0)
return ret;
/*
* Program the platform specific configuration values to the device
* first.
*/
ret = smb347_set_charge_current(smb);
if (ret < 0)
goto fail;
ret = smb347_set_current_limits(smb);
if (ret < 0)
goto fail;
ret = smb347_set_voltage_limits(smb);
if (ret < 0)
goto fail;
ret = smb347_set_temp_limits(smb);
if (ret < 0)
goto fail;
/* If USB charging is disabled we put the USB in suspend mode */
if (!smb->pdata->use_usb) {
ret = regmap_update_bits(smb->regmap, CMD_A,
CMD_A_SUSPEND_ENABLED,
CMD_A_SUSPEND_ENABLED);
if (ret < 0)
goto fail;
}
/*
* If configured by platform data, we enable hardware Auto-OTG
* support for driving VBUS. Otherwise we disable it.
*/
ret = regmap_update_bits(smb->regmap, CFG_OTHER, CFG_OTHER_RID_MASK,
smb->pdata->use_usb_otg ? CFG_OTHER_RID_ENABLED_AUTO_OTG : 0);
if (ret < 0)
goto fail;
/*
* Make the charging functionality controllable by a write to the
* command register unless pin control is specified in the platform
* data.
*/
switch (smb->pdata->enable_control) {
case SMB347_CHG_ENABLE_PIN_ACTIVE_LOW:
val = CFG_PIN_EN_CTRL_ACTIVE_LOW;
break;
case SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH:
val = CFG_PIN_EN_CTRL_ACTIVE_HIGH;
break;
default:
val = 0;
break;
}
ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_CTRL_MASK,
val);
if (ret < 0)
goto fail;
/* Disable Automatic Power Source Detection (APSD) interrupt. */
ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_APSD_IRQ, 0);
if (ret < 0)
goto fail;
ret = smb347_update_ps_status(smb);
if (ret < 0)
goto fail;
ret = smb347_start_stop_charging(smb);
fail:
smb347_set_writable(smb, false);
return ret;
}
static irqreturn_t smb347_interrupt(int irq, void *data)
{
struct smb347_charger *smb = data;
unsigned int stat_c, irqstat_c, irqstat_d, irqstat_e;
bool handled = false;
int ret;
ret = regmap_read(smb->regmap, STAT_C, &stat_c);
if (ret < 0) {
dev_warn(smb->dev, "reading STAT_C failed\n");
return IRQ_NONE;
}
ret = regmap_read(smb->regmap, IRQSTAT_C, &irqstat_c);
if (ret < 0) {
dev_warn(smb->dev, "reading IRQSTAT_C failed\n");
return IRQ_NONE;
}
ret = regmap_read(smb->regmap, IRQSTAT_D, &irqstat_d);
if (ret < 0) {
dev_warn(smb->dev, "reading IRQSTAT_D failed\n");
return IRQ_NONE;
}
ret = regmap_read(smb->regmap, IRQSTAT_E, &irqstat_e);
if (ret < 0) {
dev_warn(smb->dev, "reading IRQSTAT_E failed\n");
return IRQ_NONE;
}
/*
* If we get charger error we report the error back to user.
* If the error is recovered charging will resume again.
*/
if (stat_c & STAT_C_CHARGER_ERROR) {
dev_err(smb->dev, "charging stopped due to charger error\n");
power_supply_changed(smb->battery);
handled = true;
}
/*
* If we reached the termination current the battery is charged and
* we can update the status now. Charging is automatically
* disabled by the hardware.
*/
if (irqstat_c & (IRQSTAT_C_TERMINATION_IRQ | IRQSTAT_C_TAPER_IRQ)) {
if (irqstat_c & IRQSTAT_C_TERMINATION_STAT)
power_supply_changed(smb->battery);
dev_dbg(smb->dev, "going to HW maintenance mode\n");
handled = true;
}
/*
* If we got a charger timeout INT that means the charge
* full is not detected with in charge timeout value.
*/
if (irqstat_d & IRQSTAT_D_CHARGE_TIMEOUT_IRQ) {
dev_dbg(smb->dev, "total Charge Timeout INT received\n");
if (irqstat_d & IRQSTAT_D_CHARGE_TIMEOUT_STAT)
dev_warn(smb->dev, "charging stopped due to timeout\n");
power_supply_changed(smb->battery);
handled = true;
}
/*
* If we got an under voltage interrupt it means that AC/USB input
* was connected or disconnected.
*/
if (irqstat_e & (IRQSTAT_E_USBIN_UV_IRQ | IRQSTAT_E_DCIN_UV_IRQ)) {
if (smb347_update_ps_status(smb) > 0) {
smb347_start_stop_charging(smb);
if (smb->pdata->use_mains)
power_supply_changed(smb->mains);
if (smb->pdata->use_usb)
power_supply_changed(smb->usb);
}
handled = true;
}
return handled ? IRQ_HANDLED : IRQ_NONE;
}
static int smb347_irq_set(struct smb347_charger *smb, bool enable)
{
int ret;
ret = smb347_set_writable(smb, true);
if (ret < 0)
return ret;
/*
* Enable/disable interrupts for:
* - under voltage
* - termination current reached
* - charger timeout
* - charger error
*/
ret = regmap_update_bits(smb->regmap, CFG_FAULT_IRQ, 0xff,
enable ? CFG_FAULT_IRQ_DCIN_UV : 0);
if (ret < 0)
goto fail;
ret = regmap_update_bits(smb->regmap, CFG_STATUS_IRQ, 0xff,
enable ? (CFG_STATUS_IRQ_TERMINATION_OR_TAPER |
CFG_STATUS_IRQ_CHARGE_TIMEOUT) : 0);
if (ret < 0)
goto fail;
ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_CHARGER_ERROR,
enable ? CFG_PIN_EN_CHARGER_ERROR : 0);
fail:
smb347_set_writable(smb, false);
return ret;
}
static inline int smb347_irq_enable(struct smb347_charger *smb)
{
return smb347_irq_set(smb, true);
}
static inline int smb347_irq_disable(struct smb347_charger *smb)
{
return smb347_irq_set(smb, false);
}
static int smb347_irq_init(struct smb347_charger *smb,
struct i2c_client *client)
{
const struct smb347_charger_platform_data *pdata = smb->pdata;
int ret, irq = gpio_to_irq(pdata->irq_gpio);
ret = gpio_request_one(pdata->irq_gpio, GPIOF_IN, client->name);
if (ret < 0)
goto fail;
ret = request_threaded_irq(irq, NULL, smb347_interrupt,
IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
client->name, smb);
if (ret < 0)
goto fail_gpio;
ret = smb347_set_writable(smb, true);
if (ret < 0)
goto fail_irq;
/*
* Configure the STAT output to be suitable for interrupts: disable
* all other output (except interrupts) and make it active low.
*/
ret = regmap_update_bits(smb->regmap, CFG_STAT,
CFG_STAT_ACTIVE_HIGH | CFG_STAT_DISABLED,
CFG_STAT_DISABLED);
if (ret < 0)
goto fail_readonly;
smb347_set_writable(smb, false);
client->irq = irq;
return 0;
fail_readonly:
smb347_set_writable(smb, false);
fail_irq:
free_irq(irq, smb);
fail_gpio:
gpio_free(pdata->irq_gpio);
fail:
client->irq = 0;
return ret;
}
/*
* Returns the constant charge current programmed
* into the charger in uA.
*/
static int get_const_charge_current(struct smb347_charger *smb)
{
int ret, intval;
unsigned int v;
if (!smb347_is_ps_online(smb))
return -ENODATA;
ret = regmap_read(smb->regmap, STAT_B, &v);
if (ret < 0)
return ret;
/*
* The current value is composition of FCC and PCC values
* and we can detect which table to use from bit 5.
*/
if (v & 0x20) {
intval = hw_to_current(fcc_tbl, ARRAY_SIZE(fcc_tbl), v & 7);
} else {
v >>= 3;
intval = hw_to_current(pcc_tbl, ARRAY_SIZE(pcc_tbl), v & 7);
}
return intval;
}
/*
* Returns the constant charge voltage programmed
* into the charger in uV.
*/
static int get_const_charge_voltage(struct smb347_charger *smb)
{
int ret, intval;
unsigned int v;
if (!smb347_is_ps_online(smb))
return -ENODATA;
ret = regmap_read(smb->regmap, STAT_A, &v);
if (ret < 0)
return ret;
v &= STAT_A_FLOAT_VOLTAGE_MASK;
if (v > 0x3d)
v = 0x3d;
intval = 3500000 + v * 20000;
return intval;
}
static int smb347_mains_get_property(struct power_supply *psy,
enum power_supply_property prop,
union power_supply_propval *val)
{
struct smb347_charger *smb = power_supply_get_drvdata(psy);
int ret;
switch (prop) {
case POWER_SUPPLY_PROP_ONLINE:
val->intval = smb->mains_online;
break;
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
ret = get_const_charge_voltage(smb);
if (ret < 0)
return ret;
else
val->intval = ret;
break;
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
ret = get_const_charge_current(smb);
if (ret < 0)
return ret;
else
val->intval = ret;
break;
default:
return -EINVAL;
}
return 0;
}
static enum power_supply_property smb347_mains_properties[] = {
POWER_SUPPLY_PROP_ONLINE,
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
};
static int smb347_usb_get_property(struct power_supply *psy,
enum power_supply_property prop,
union power_supply_propval *val)
{
struct smb347_charger *smb = power_supply_get_drvdata(psy);
int ret;
switch (prop) {
case POWER_SUPPLY_PROP_ONLINE:
val->intval = smb->usb_online;
break;
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
ret = get_const_charge_voltage(smb);
if (ret < 0)
return ret;
else
val->intval = ret;
break;
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
ret = get_const_charge_current(smb);
if (ret < 0)
return ret;
else
val->intval = ret;
break;
default:
return -EINVAL;
}
return 0;
}
static enum power_supply_property smb347_usb_properties[] = {
POWER_SUPPLY_PROP_ONLINE,
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
};
static int smb347_get_charging_status(struct smb347_charger *smb)
{
int ret, status;
unsigned int val;
if (!smb347_is_ps_online(smb))
return POWER_SUPPLY_STATUS_DISCHARGING;
ret = regmap_read(smb->regmap, STAT_C, &val);
if (ret < 0)
return ret;
if ((val & STAT_C_CHARGER_ERROR) ||
(val & STAT_C_HOLDOFF_STAT)) {
/*
* set to NOT CHARGING upon charger error
* or charging has stopped.
*/
status = POWER_SUPPLY_STATUS_NOT_CHARGING;
} else {
if ((val & STAT_C_CHG_MASK) >> STAT_C_CHG_SHIFT) {
/*
* set to charging if battery is in pre-charge,
* fast charge or taper charging mode.
*/
status = POWER_SUPPLY_STATUS_CHARGING;
} else if (val & STAT_C_CHG_TERM) {
/*
* set the status to FULL if battery is not in pre
* charge, fast charge or taper charging mode AND
* charging is terminated at least once.
*/
status = POWER_SUPPLY_STATUS_FULL;
} else {
/*
* in this case no charger error or termination
* occured but charging is not in progress!!!
*/
status = POWER_SUPPLY_STATUS_NOT_CHARGING;
}
}
return status;
}
static int smb347_battery_get_property(struct power_supply *psy,
enum power_supply_property prop,
union power_supply_propval *val)
{
struct smb347_charger *smb = power_supply_get_drvdata(psy);
const struct smb347_charger_platform_data *pdata = smb->pdata;
int ret;
ret = smb347_update_ps_status(smb);
if (ret < 0)
return ret;
switch (prop) {
case POWER_SUPPLY_PROP_STATUS:
ret = smb347_get_charging_status(smb);
if (ret < 0)
return ret;
val->intval = ret;
break;
case POWER_SUPPLY_PROP_CHARGE_TYPE:
if (!smb347_is_ps_online(smb))
return -ENODATA;
/*
* We handle trickle and pre-charging the same, and taper
* and none the same.
*/
switch (smb347_charging_status(smb)) {
case 1:
val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
break;
case 2:
val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
break;
default:
val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
break;
}
break;
case POWER_SUPPLY_PROP_TECHNOLOGY:
val->intval = pdata->battery_info.technology;
break;
case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
val->intval = pdata->battery_info.voltage_min_design;
break;
case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
val->intval = pdata->battery_info.voltage_max_design;
break;
case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
val->intval = pdata->battery_info.charge_full_design;
break;
case POWER_SUPPLY_PROP_MODEL_NAME:
val->strval = pdata->battery_info.name;
break;
default:
return -EINVAL;
}
return 0;
}
static enum power_supply_property smb347_battery_properties[] = {
POWER_SUPPLY_PROP_STATUS,
POWER_SUPPLY_PROP_CHARGE_TYPE,
POWER_SUPPLY_PROP_TECHNOLOGY,
POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
POWER_SUPPLY_PROP_MODEL_NAME,
};
static bool smb347_volatile_reg(struct device *dev, unsigned int reg)
{
switch (reg) {
case IRQSTAT_A:
case IRQSTAT_C:
case IRQSTAT_E:
case IRQSTAT_F:
case STAT_A:
case STAT_B:
case STAT_C:
case STAT_E:
return true;
}
return false;
}
static bool smb347_readable_reg(struct device *dev, unsigned int reg)
{
switch (reg) {
case CFG_CHARGE_CURRENT:
case CFG_CURRENT_LIMIT:
case CFG_FLOAT_VOLTAGE:
case CFG_STAT:
case CFG_PIN:
case CFG_THERM:
case CFG_SYSOK:
case CFG_OTHER:
case CFG_OTG:
case CFG_TEMP_LIMIT:
case CFG_FAULT_IRQ:
case CFG_STATUS_IRQ:
case CFG_ADDRESS:
case CMD_A:
case CMD_B:
case CMD_C:
return true;
}
return smb347_volatile_reg(dev, reg);
}
static const struct regmap_config smb347_regmap = {
.reg_bits = 8,
.val_bits = 8,
.max_register = SMB347_MAX_REGISTER,
.volatile_reg = smb347_volatile_reg,
.readable_reg = smb347_readable_reg,
};
static const struct power_supply_desc smb347_mains_desc = {
.name = "smb347-mains",
.type = POWER_SUPPLY_TYPE_MAINS,
.get_property = smb347_mains_get_property,
.properties = smb347_mains_properties,
.num_properties = ARRAY_SIZE(smb347_mains_properties),
};
static const struct power_supply_desc smb347_usb_desc = {
.name = "smb347-usb",
.type = POWER_SUPPLY_TYPE_USB,
.get_property = smb347_usb_get_property,
.properties = smb347_usb_properties,
.num_properties = ARRAY_SIZE(smb347_usb_properties),
};
static const struct power_supply_desc smb347_battery_desc = {
.name = "smb347-battery",
.type = POWER_SUPPLY_TYPE_BATTERY,
.get_property = smb347_battery_get_property,
.properties = smb347_battery_properties,
.num_properties = ARRAY_SIZE(smb347_battery_properties),
};
static int smb347_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
static char *battery[] = { "smb347-battery" };
const struct smb347_charger_platform_data *pdata;
struct power_supply_config mains_usb_cfg = {}, battery_cfg = {};
struct device *dev = &client->dev;
struct smb347_charger *smb;
int ret;
pdata = dev->platform_data;
if (!pdata)
return -EINVAL;
if (!pdata->use_mains && !pdata->use_usb)
return -EINVAL;
smb = devm_kzalloc(dev, sizeof(*smb), GFP_KERNEL);
if (!smb)
return -ENOMEM;
i2c_set_clientdata(client, smb);
mutex_init(&smb->lock);
smb->dev = &client->dev;
smb->pdata = pdata;
smb->regmap = devm_regmap_init_i2c(client, &smb347_regmap);
if (IS_ERR(smb->regmap))
return PTR_ERR(smb->regmap);
ret = smb347_hw_init(smb);
if (ret < 0)
return ret;
mains_usb_cfg.supplied_to = battery;
mains_usb_cfg.num_supplicants = ARRAY_SIZE(battery);
mains_usb_cfg.drv_data = smb;
if (smb->pdata->use_mains) {
smb->mains = power_supply_register(dev, &smb347_mains_desc,
&mains_usb_cfg);
if (IS_ERR(smb->mains))
return PTR_ERR(smb->mains);
}
if (smb->pdata->use_usb) {
smb->usb = power_supply_register(dev, &smb347_usb_desc,
&mains_usb_cfg);
if (IS_ERR(smb->usb)) {
if (smb->pdata->use_mains)
power_supply_unregister(smb->mains);
return PTR_ERR(smb->usb);
}
}
battery_cfg.drv_data = smb;
smb->battery = power_supply_register(dev, &smb347_battery_desc,
&battery_cfg);
if (IS_ERR(smb->battery)) {
if (smb->pdata->use_usb)
power_supply_unregister(smb->usb);
if (smb->pdata->use_mains)
power_supply_unregister(smb->mains);
return PTR_ERR(smb->battery);
}
/*
* Interrupt pin is optional. If it is connected, we setup the
* interrupt support here.
*/
if (pdata->irq_gpio >= 0) {
ret = smb347_irq_init(smb, client);
if (ret < 0) {
dev_warn(dev, "failed to initialize IRQ: %d\n", ret);
dev_warn(dev, "disabling IRQ support\n");
} else {
smb347_irq_enable(smb);
}
}
return 0;
}
static int smb347_remove(struct i2c_client *client)
{
struct smb347_charger *smb = i2c_get_clientdata(client);
if (client->irq) {
smb347_irq_disable(smb);
free_irq(client->irq, smb);
gpio_free(smb->pdata->irq_gpio);
}
power_supply_unregister(smb->battery);
if (smb->pdata->use_usb)
power_supply_unregister(smb->usb);
if (smb->pdata->use_mains)
power_supply_unregister(smb->mains);
return 0;
}
static const struct i2c_device_id smb347_id[] = {
{ "smb347", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, smb347_id);
static struct i2c_driver smb347_driver = {
.driver = {
.name = "smb347",
},
.probe = smb347_probe,
.remove = smb347_remove,
.id_table = smb347_id,
};
module_i2c_driver(smb347_driver);
MODULE_AUTHOR("Bruce E. Robertson <bruce.e.robertson@intel.com>");
MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
MODULE_DESCRIPTION("SMB347 battery charger driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("i2c:smb347");